Chevrolet - Suburban :: 2001 - Parking Brake Adjustment
Nov 19, 2011
How do I adjust the parking brake on my 2001 Suburban? It is a 2wd 1500 model.
View 3 Replies
Nov 19, 2011
Advertisement
Ford Super Duty (1999-2016) :: 2012 F250 - Parking Brake And E-brake Adjustment?
The problem is I haven't seen one for a recent (2011+) SD. I don't see anything that resembles a rear drum. They look like 2 huge regular disc brakes.
I live on a hill. My old man taught me to put the trans in neutral, autos and manuals, put the ebrake on and make sure it holds the vehicle, then put the trans into park or 1st gear. This way the weight of the vehicle doesn't rest on the transmission.
How do I adjust the Ebrake? It's ALMOST holding the truck, just needs a minor tweak. I don't see the dust cover the write ups described at all. The one that reveals the Star Wheel. Are they different on these years then prior SD's?
Prius (Gen 2) :: Parking Brake Adjustment?
I have the weekend clear. My husband is gone -- so no second-guessing.
I WANT to adjust the parking brake. I ordered the Chilton manual nearly two weeks ago. As of tonight it is sitting in Hermiston, Oregon, about a three-hour drive away. I don't suppose it is getting delivered to my house tommorrow (Saturday).
I have checked out a few online spots that tout instructions. They are either pretty vague, or somewhat scary. I have adjusted the PB on my old Toyota Corolla....many times.
Prius (2010-12) :: Parking Brake Adjustment?
When I was at Luscious Garage earlier today for a transmission service, the technician told me that my parking brake is out of adjustment. Sure enough, I checked the factory service manual when I got home and found that the spec is 8-11 notches at 67.5lbf. My own test revealed that it was taking between 15-17 notches on mine!
View 7 RepliesCivic - Honda :: 1997 - Parking Brake Adjustment
I recently had some work done on my 97 Honda Civic (manual), and asked them to adjust the parking brake while they were at it. They tightened it up as they usually do when they work on the car (the other work was not brake-related, although they DID replace my master cylinder just back in February). Two days later, my brakes began to fail (much like they had when I needed the master cylinder replaced). Turns out, something happened with the parking brake such that the cables seized or something and caused the regular brakes to overheat. Once they cooled down, the regular brakes were fine again, so they disconnected one of the cables for the parking brake and ordered replacement cables to be installed next week, for a not inconsequential sum. My question is: did they screw up when they adjusted the parking brake, such that I shouldn't really have to pay the full amount for this subsequent repair? Or was this likely inevitable?
View 12 RepliesLexus RX 2010-15 :: Parking Brake Adjustment On 2011 RX350
What is the procedure for adjusting the parking brake shoes on a 2011 Rx 350? How many clicks from tight should it be?
View 5 RepliesSonata NF (2006-10) :: 2008 - Parking Brake Not Holding - Adjustment?
I have an 08 Sonata that just failed inspection due to the parking brake not holding. With the lever full up the E brake doesn't stop the vehicle at idle.
The rear wheels have disc brakes. How do I adjust the cable to remove the slack. I believe there's a center drum so I suspect there's a star wheel that must be adjusted. If so, which way does the star wheel need to turn, up or down. Is it the same direction on both the left and and right side of the vehicle?
Toyota - Camry :: Parking Brake Barely Holds While In Drive - Adjustment?
05 Camry, 2.4L, 47K. Vehicle parking brake barely holds while in Drive. How is this adjusted? On my 91 Corolla, the brake adjusts itself by pulling up on the handle. The Camry does not have this feature so does this have an adjustable cable? If so, where did they hide this adjuster?
View 15 RepliesFord Brakes/Suspension :: 1993 F250 - Parking Brake Adjustment?
So it looks like there is no adjustment on the Parking Brake on this ride other than adjusting the shoes up. As far as I can see my Parking Brake should work like a champ, but it won't hold on much of a hill. I have new shoes, new drums and it is adjusted up so I can hear them drag. I can actually feel it getting tight then looser as you spin the wheel, like one of the new drums is slightly out of round, so I don't think I could go much tighter. Is it possible one or more of the cables is stretched? I did see the shoes spread when I had the drums off and I stepped on the Park Brake, so I know things are working at least that much.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Parking Brake Adjustment?
How do I adjust the parking brake on my 08 F250? It's not holding when my truck is parked on a hill.
View 1 RepliesFord Super Duty (1999-2016) :: 2006 - Parking Brake On Rear Disks Adjustment?
Are the parking brakes on rear disks adjustable at all? Mine doesn't hold very well anymore, but I'm not quite ready to rebuild the whole thing. If there are adjusters (similar to drums), which way you turn them on which side of the truck?
View 6 RepliesChevrolet - Suburban :: Odd Brake Related Noise Like Spring Tension Being Released
Vehicle is a 94 Suburban. The front brakes were done approximately 14K miles ago. Rear about 10K miles ago. Ever since the front brake job (new rotors, pads) there has been a sound, sort of like spring tension being released whenever I (quickly) release the brake pedal. I think I notice it now more than ever because I don't have working ac and the windows are usually down. The thing is, if I slowly release the pedal I hear nothing. When it does happen it is definitely coming from the front and is more predominant (I think) on the right side. So far I have yet to hear this sound coming from any other vehicle stopped beside me in traffic so something must be out of whack.
I mentioned this to the mechanic who did the brakes (only shortly thereafter) and he checked it out and said nothing was amiss. Recently I had new tires installed so I asked the (different) mechanic to check the brakes again (front and rear). Apart from cleaning out the drums and a minor adjustment on the rear they said everything was good. Now I've never had any issues with stopping and I've had a few hard braking episodes without incident but this snapping noise for want of a better description is driving me nuts. One final observation: I cannot get the 'sound' to occur when I am sitting in Park and depress and then quickly release the brake pedal.
Gasoline - Chevrolet - Suburban - Flex :: 2008 - Slight Stumble When Idling With The Brake On Or In Park
I have the 5.3L FLEX Fuel with 98K miles. I have purchased this 2nd hand and having a slight idle stumble when in park as well as in drive @ a stop light...etc. If i am under way, the vehicle runs flawlessly. When i am idling with the brake on or in park, there is a slight stumble that is driving me crazy. I have replaced the high dollar IRIDIUM plugs but did not replace the wires...they looked fine. I did clean the throttle body. I get fuel from different places and it does not make a difference. I have not cleaned the fuel system professionally but I have used OTC additives such as SeaFoam. No codes are exhibited on a diagnostic computer or any updates available for that matter.
View 11 RepliesChevrolet - Suburban :: 2001 - Engine Severely Lacking In Torque For The First Minute Or So Of Driving
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
Elantra XD (2001-06) :: 2004 - Rear Brake Sticks / Parking Brake Is Broken
I have a 2004 Elantra GLS. My left rear brake was hanging (wheel was very hot to the touch after driving, while other wheels were not), so I had a friend check the brake pads. We decided to replace the pads and rotors. While doing so, the parking brake seemed stuck in the on position, so I opted to have him disconnect it completely until I could afford to replace it. I had used it for the first time about 2 weeks before I noticed the hot brake problem, so we figured that must have been why the brake was hanging.
My friend replaced the rotors and pads, put some penetrant/lubricant on the piston of the caliper and reassembled the brakes. He did use the special tool to spin the caliper in when putting the pads on, however he didn't know that was necessary and tried to force them in with a C-clamp first.
Now, I seem to have two problems:
1. The left rear brake still hangs sometimes. I will drive the car and when I park it I can feel the heat coming off of the left rear wheel. It is extremely hot, so I know the brake is hanging (even with the parking brake disconnected). What is the problem here? Is the caliper bad? Would replacing the caliper solve the problem? Does the parking brake have to be connected to stop the caliper from hanging up?
2. My second problem is the pulsating of the brakes. I am afraid the rotor is warped because of the heat, or maybe he didn't clean everything well enough before he put the new rotor on. How can I figure out what the problem is? Is there a way to check a rotor to see if it is warped? Could there be another reason I feel the pulsating brakes? By the way, the brake fluid is full.
If the caliper needs to be replaced and I can leave the parking brake disconnected, are there any special instructions my friend should know about before working on this? He does work on a lot of cars and rebuilds cars to sell, so he is pretty knowledgeable. I think the only thing he didn't know about was rotating the piston. I would like to provide him with detailed instructions if necessary.
Suburban :: 2001 - ABS And Brake Light On At Same Time Intermittently
What seems to cause this problem of the ABS and brake light coming on at the same time intermittently. I can go an hour or so then pop -- then come on. Its a 2001 with a 5.3 in it.
View 3 RepliesChevrolet - Suburban :: 2001 - Constant ABS / Flashing Service Ride Control And Change Engine Oil Warning
I checked the cables, no corrosion and tight as a drum. I connected an OBD II computer to the plug under the dashboard and the computer replied that there were no trouble codes present. Is OBDII the proper code reader? none of these lights were on before I replaced the battery. now I have constant ABS, flashing Service ride control, change engine oil. The battery has not gone dead as of yet but the ampmeter is charging at about 16.5-17 volts. I disconnected the pos terminal while the vehicle was running and it continued to run even with the lights on.
View 2 RepliesChevrolet - Tracker :: 2003 - Headlights Come On Automatically While Parking Brake Released?
I'm having trouble with the headlights on my 2003 Chevy Tracker. When it's light out, my headlights come on automatically when I release the parking brake, but turn off if I turn the switch that would normally turn them on. When it is dark out, or I drive under a bridge etc, they turn off and I can't manually turn them on. I can "flash" my headlights, but if I turn them on as if to leave them on, they don't turn on. This problem started about the same time that my AC blower stopped working, so I replaced the blower motor resistor and all fuses (I've heard that the blower motor resistor is also involved with the headlights). This fixed the AC, but had no effect on the headlights.
I can trick the lights into turning on at night only by shining a bright light directly on the sensor - they turn back off as soon as I remove the light. I took it to Pep Boys for a basic electrical diagnostic to see if I might be missing something silly, but once I described the problem they wouldn't even bother - told me to take it to the dealer and have the body regulator module reprogrammed.
Chevrolet - Tahoe :: Parking Brake / Pedal Moved Down With No Resistance When Stepped On
I was driving my 98 Tahoe yesterday making a visit to my sister. pulled the truck into the drive-way, put the gear selector in park, stepped on the parking brake (a habit I've had for years) and YIKES! the peddle moved down with no resistance!
my parking brake light stayed on even after I released the parking brake peddle, which didn't spring back, but I pulled it back. light stayed on when I started the truck although I think the brake never engaged in the first place.
I drove the truck and didn't notice any drag at all. after driving a few miles I stopped the truck and felt the wheels for excessive heat but didn't experience that. my guess is the cable broke or came off and didn't engage the parking brake in the first place. sound correct?
Chevrolet - Cobalt :: 2010 - Parking Brake Light Comes On / Speedo And RPM Gauges Stop Working
I have a 2010 Chev Cobalt LT, bought brand new off the lot- at about 15,000 km's, I started to experience some electrical issues.. Basically, what it is the parking brake light comes on in the instrument panel along with the all the other warning lights, both speedo and rpm gauges stop working, -- basically EVERYTHING electrical, but the lights, and turn signals, hazards work-- took it in to the GM Dealer- they cleaned the BCM Connectors, it was fine for about 4 months- now it's doing it again... Same thing as before warning lights come on, and everything stops except last night the Keyless Entry would not work at all... This has me stumped and it's annoying having to take it all the time..
View 4 RepliesTouareg :: When Parking Brake Released In MFI Got Warning Parking Brake Fail To Release
Had my car parked outside of work for about 12 hours yesterday, and in the NYC cold front, the parking break must have stuck on slightly. When I started to move, despite the fact I'd released the parking break, I received a warning in the MFI that said PARKING BREAK FAILURE TO RELEASE. I pulled the handle again and heard it pop just a little more off. Everything worked great after that. If I hadn't received the alert I probably would have driven off with it on. I'd probably have noticed the hesitation and checked the break again, but the alert was useful. Some of the warnings in the MFI can appear to be a pain at times, but it's amazing how thorough a job VW has done monitoring the cars systems and giving real time information if something doesn't work. You just have to make sure you don't get info overload from it all!!
View 4 Replies