Chevrolet - Suburban :: 1994 - High Idle All The Time
Sep 24, 2012
I have a 94 C2500 suburban with a TBI 454BB. Obviously, I'm not concerned with fuel mileage, but I am currently getting about 4 miles to the gallon because the idle is stuck at 1800RPM. Normal idle for my model according to the index book is 750RPM. it's usually pretty close to that when operating normally (+/-25RPM). 3 days ago I did my biannual throttle body cleaning. Took it completely off replaced the gasket cleaned the throttle body and put it all back together. This is when the problem started... It now idles at 2300 RPM, it threw the code for bad idle air control valve, and I figured I probably got the plug wet when cleaning the throttle body, so I went ahead and ate the 60 bucks and replaced it.
Went through the reset process for the ECM to learn the new one and it the idle has come down to 1800RPM, it also literally DUMPING fuel through the injectors into the top of the throttle body. While I don't believe it is actually running rich, it seems more like the idle is trying to compensate for the excess fuel that is being dumped into the top end. Now, Before I go any further I want someone else's input. "I" think it is a also a bad throttle position sensor that probably got wet when cleaning the TB. But I am worried it could also be the PCM has finally gone out, although this is probably not likely because the entire ignition is run by this and if it was bad, it would stand to reason that it wouldn't run at all. Or it could be a bad vacuums control module. I have checked all my vacuum lines and do not have any leaks, so I know that isn't the problem. So that's where I am. I am hoping to check the leads on the TPS today with a ohm meter. I know my resistance levels.
View 5 Replies
Advertisement
"step on gas, truck feel like it is pulling a house, slight buck, but with more gas it moves, it has good presure out the exhast, all wheels are turning freely, engine idles great has lots of power,"
tested, cyl pressure, fine
check engine timing, fine
made sure all wheels spin freely, fine
check all fluids, fine
slight pinging sound can be heard, from time to time from center of truck. I'm thinking torque convertor. Feels like engine is binding only when you put it in gear.
View 4 Replies
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 Replies
I have a 94 Chevy Suburban C1500 with a 5.7L, 350 Engine. It has 235,000 miles on it. I purchased it about 4 years ago with 191,000 miles in very good condition and obviously well maintained. I have continued to maintain it well.
For the past few months it has begun to start a little slower that before and when accelerating cold or warm there is a spot where it looses power. It doesn't sputter or die it just looses power. I can press the accelerator farther and it will come back to life and do fine. After a 20 -30 minute drive if I park for a while, 20 - 30 minutes, when I start it up it dies. The only way to keep it running is to give it the gas and smooth it out at about 1500 rpm for 10 - 15 seconds. Then I can drive it with no problem most of the time though it still has the dead spot on acceleration.
There is a good spray pattern from the throttle body injectors. Plugs and wires are relatively new and plugs look good (AC Delco Rapidfire Platinum). When I turn on the ignition without going to start, the fuel pump builds pressure for 4 - 6 seconds. I haven't checked the fuel pressure yet and am considering investing in the rig to do so. I recently replaced the fuel filter but that didn't work.
The check engine light has not come on but many of the lights in the cluster are burned out and I haven't felt like going to the trouble to fix that so it is possible that the check engine bulb is bad.
View 12 Replies
I have a 1995 Chevrolet Suburban that the a/c fan speed works on every position except high. I have replaced the resistor and the fan speed switch. Neither of those things fixed the problem. With the connector off the blower motor and a test light attached, power is present in all positions except high. When switched to the high speed position power is not present in the lead.
View 3 Replies
We have a 94 corsica that we have trouble starting. I realized after a few times of this problem that, if when you turn the key to "Run" the lights ( Seat belt, Brake, oil, check engine etc..) are not lit up, but if you wait for a minute, those lights will light and the engine will then start. when those lights go on, it will start without a problem. But if those lights have not come on it will crank, but never fire. If it's the computer, or some other device that is hesitating for that minute, before allowing it to start. Other than this problem the engine runs fine.
View 1 Replies
My 2001 Suburban, 1500, 5.3L, 2WD with 164k miles, has a problem with high idle and delayed shifting. The high idle occurs when the vehicle has been driven around for awhile. When I start it up, even when already warm, idle is normal (~600 rpm). After some time, however, it idles at 900 to 1100 rpm. The delayed shifting happens right away--almost like I have the tow/haul mode turned on.
I have cleaned out the idle air port, cleaned the MAF sensor, replaced the idle air control valve, replaced the PCV valve, replaced the engine temperature sensor, and unhooked the battery to reset things. It still idles high.
I first noticed this a few weeks ago when the battery died. After I put in the new battery, the idle was very low. So I cleaned out the idle air port and valve. Then it was high. I drove it around for a few days like that and then started replacing stuff, to no avail--still high. I also cleaned around the throttle plate.
View 4 Replies
I recently purchased a 1994 Chevy Corsica that is in excellent shape for the year with one exception. I can't get the high beams to come on. When I pull back on the turn signal lever, nothing happens. I know that most of them make a "click" noise when you pull on them, but this one doesn't. Is the high beam switch a part of the turn signal switch that is in the steering column? I am not sure what else to try.
View 4 Replies
1995 C1500 Suburban (diesel) ... Felt like the transmission started to slip. And then it slowly started to "idle down while driving". thought maybe out of fuel, so i filled it up. When i turned out of the Gas station it died. about 20 minutes later, it started up but still didn't seem to run at full strength. No engine lights on or anything, light all still worked fine, just the engine shut off on me.
View 6 Replies
I have a 4.3l CPi vin w 1994 s10 zr2 .... At a idle it revs up and down from 500.-1500rpms? Loading up on fuel and dies after idling after a short time. And while going down the road it cuts out like its going to die then it catches itself. Yesterday I put a new idle air controls sensor on and it fixed nothing !!!!!
View 14 Replies
I continue to have problems with my Chevy Beretta. The original problem was that -- after my neice's husband ran the car out of gas -- we had to replace the fuel filter. That was last spring. Afterward the car seemed to run fine until the weather got hot. Now it seems to stall generally in high heat and humidity.
I only paid $800 for the car, and my idea was to get everything fixed on it and drive it a while to get my money out of it. I don't want to go into debt for a car, and I don't want to buy another one (unless I have to). I travel a lot, but I don't need my car for work -- just for personal travel.
A local mechanic has changed the crankshaft position sensor and now the ignition module. I got the car out of the shop again yesterday, but the problem remains. I could barely drive it around the block this evening. The temperature is 73F, humidity is 84%, and dewpoint is 68.
Is this problem definitely weather related? What could be the cause? Vapor lock? An intermittent problem with the fuel pump, filters, or fuel injector? Is it possible to get this fixed for good?
View 6 Replies
94 Chevy W-4 wheel-lift wrecker 5.7L TBI4l80e trans
Had a run of about 100 miles round trip on Wednesday. On the way back running at 65 mph on the interstate, got a couple of quick muffler-end back fires and engine died. Coasted to shoulder. Had memory of almost exact same incident last year and it was dead ignition module. Fortunately had a spare (used) module in glovebox. Swapped it out and engine started right up. Remainder of trip didn't quit, but ran very rough, lots of stumbling and getting it up to 60 mph was a struggle. Also when I got on surface roads it died twice when I was sitting stationary. It would restart, BUT only after cycling key; if I just turned to the key to "start" from "on" it would crank but not fire.
Limped it to my tow buddy's shop where I freeload and told him the tale. He said, "throw those old spare modules away and get a new one". Called the local parts house and had them send two, one for installation and one for glovebox. Took for test drive and appeared to be running okay except idle was a bit low. Couple of hours later went on a call and first stop sign I came to, went "blip" and I'm dead in the water again. Same story as earlier, must turn key off and back on to get it to fire. Drove rest of day without incident. Yesterday, no issues all day, drove total of about 120 miles both highway speed and surface. Gassed up this morning and mpg was above average (yay!), actually about .5 above average which is significant improvement (about 6%). Success?
Today died four times while sitting still. Same having to cycle key for it to fire. Did some quicky t/s to satisfy my curiosity about the key cycle thing. With truck running, pulled fuel pump fuse to kill truck. Then reinserted and it started up without having to turn key to off. Tried same thing by pulling one of the module plugs to simulate loss of signal to ignition. Reconnected and again fired up without key cycling.
No codes at any time since this came up.
Swapped out the module since I had bought a spare, no change.
Ohmd the ignition coil and no problems noted. So far, only dies sitting still at idle.
Additional info:
Plug wires, cap, and rotor <1000 miles. Distributor low miles and negligible play in shaft. Pickup coil checks right in middle of ohm range. None of these, of course, should need to have the ignition key cycled to restart if they caused a stall.
Next up will be replacing ignition relay (had to order), but I'm not very optimistic.
View 4 Replies
I have had this issue with the braking system for about a year now. Most of the time when using the brakes, everything works fine, but once in awhile, it seems like the brakes on one (I think one) wheel seem to just let go, apply full braking power, or both one after the other. When this happens, you hear loud clunking sounds (which I guess it the caliper going from on to full off and back again) and the rear of the car will raise and lower with the instances. There are also times when a high pitched squeak sound comes from the wheel (like when a bus uses their brakes) which will normally happen a second before coming to a full stop. It does not happen at the same time, but I think is related. Going off the sounds and rear of the car moving I tend to think this is focusing around the driver's rear tire. The brake fluid has been changed, the brakes have been changed on all 4 wheels, and so have the all brake lines to the cylinders. There are no leaks anywhere in the system. The car does have ABS.
View 13 Replies
1994 corvette auto trans, when car is parked or in drive with foot on the brake will start to idle up, the back down and like lunge forward if in drive and foot on the brake. Then if you drive it, and step on it, it will miss fire. My mechanis put it on his scanner but it showed no problems. The opti- spark, wires, plugs were replaced 2 years ago and 12,000 miles ago.
View 8 Replies
I have a ac compressor that doesn't work all the time. I have read how voltage or low power can effect this. When mine does not start up, if you tap the end of the compressor with a rubber mallet, it engages and runs fine for an extended period. Am I dealing with a power supply issue, or could this just be a bad ac clutch?
View 1 Replies
My question is what could cause a high idle?I have a 95 Chevy pickup 4x4 with a 5.7... Recently the lower radiator hose fell came off the radiator, dumping the liquids all over the street. The motor shut down, and every time we went to start it there would be a loud whining/spinning noise. We thought that the motor seized, so we pulled the plugs, turned the motor by the crank bolt.Turned out that the starter went bad, the spindle and bendex werent catching on the flywheel.
After examining the flywheel teeth, and gapping the plugs to the recommended manufacture gap, (they werent when we pulled them), we got a new starter installed. It started right up! But it ran at a high idle, around 1500-2000 RPM. I did not have a chance to really let it warm up (it was cold and raining). Now there is a gray flexhose that is running from the air filter housing down to the exhaust manifold. If i remember correctly, it was not seated very well when I took it off. Could it be causing too much of a vacuum?
View 9 Replies
I have a 1994 suburban1500 heater is not working in front or rear and in the front I have no control on the vents it only blows on the floor flashes if I try and change from floor to vents or defrost also blows air on floor while driving with the fan off so seems that the vent is stuck open the rear I have control on vent or floor just will not blow heat just outside temp air I had the same problem with a buick I had and never figured out the problem this is driving me crazy.
View 1 Replies
First bit of cold weather and I'm getting thirty seconds of loud clicking (or clacking) coming from the immediate vicinity of the blower motor on start up and shut down. Doesn't matter whether my climate control is on or off, it still makes the noise. I'm assuming it's stripped out teeth on one of the blend door actuator gears and I'll probably just end up replacing it. My problem: Where exactly is the offending actuator? I've removed the glove box and noted one located on the left side. I unplugged this but am still getting the ratcheting sound so it obviously isn't the culprit. I had this happen a few years back (same time of year) and out of ignorance and frustration solved it with a well aimed kick but the way it's acting this time I don't think I've got a big enough boot.
View 4 Replies
What seems to cause this problem of the ABS and brake light coming on at the same time intermittently. I can go an hour or so then pop -- then come on. Its a 2001 with a 5.3 in it.
View 3 Replies
As of yesterday evening my 2002 Chevrolet Suburban 1500, shuts off while im driving. Takes about two to five minutes to get it going again (has shut off a couple times) Starts up fine idles great, problems start about a mile or two of being driven.
View 1 Replies
When turning right, it seems as if my brakes don't want to work. There is somewhat of a grinding sound and what I can only describe as a "shutter" from the pedal. They work great going straight or turning left. I should also mention that the steering locks up when turning sharply, haven't noticed if it's only when turning a certain way. This happens mostly when backing up. Also, the ABS light is on occasionally. I drive a '96 GMC Suburban.
View 7 Replies
