Chevrolet - Silverado2500 :: 1996 - Only Way To Start Is To Get Rolling And Pop Clutch
Dec 10, 2013
Problems started 2 days ago, after the weather got colder. Related? Can hear starter engage (loud click) but not enough juice to spin the engine. The only way to start is to get the rolling and pop clutch. Will not start when I attempt to jump start. When running, battery emblem in the instrument cluster is illuminated and voltage gauge shows very low. Batteries (two 12-volt 800cca batteries) old and worn out? Had alternator went bad?
View 19 Replies
Advertisement
The oil pressure gauge on my truck has jumped to 80PSI while running. What caused this? Is it a bad pressure switch or is it the gauge? If it is the switch where is it located on a 2006 Chevy truck with a 6.0?
View 8 Replies
I have a 2002 2500HD duramax that is stalling out when accelerating heavily ( as when passing ) I replaced the fuel filter, this seemed to solve the problem for a day or two. The problem returned after two days of driving. I took the new filter off and cleaned the lower float valve,replaced it & it seemed to drive fine until I took it for a test drive and "gassed it" and the problem returned.
View 1 Replies
We have a 2002 Maxima SE, 6 speed manual with 127,000 + miles. The noise is similar to what we used to hear from the spokes, when we attached a playing card or piece of cardboard to the wheels of our bikes. The noise only presents itself when the clutch is engaged and the wheels start rolling. It happens in forward and reverse.
The dealer replaced the right wheel bearing assembly and both outer tie rods. But that did not eliminate the noise. They then fingered the transmission. The transmission folks said it was not the transmission or the clutch release bearing.
Confused, we just keep driving the car. Whatever it is doesn't appear to affect the driveability - yet. The clutch engages smoothly, the shifing is smooth and it does not pop out of gear. We've been thinking of selling the car, but this noise has to be resolved first.
View 4 Replies
I have a 2000 silverado. When I come to a stop, sometimes the anti-lock brakes will kick in. it makes that all too familiar grinding/clicking sound that I hear all winter. However, it is happening during the summer/fall. It doesn't happen every time I brake. It seems to happen most when I am coming to a stop on an uphill or downhill grade, or when I am stopping while turning. It doesn't happen the whole time while braking, just right at the end before the vehicle stops. It also seems to happen more frequently when it is warmer out. The tires don't skid while it is stopping either, which I guess is supposed to happen. It is a concern since it does take me a bit longer to stop when the anti-lock is going, and I never can predict when it will happen.
View 3 Replies
I am having trouble with my air conditioning system in my 1996 Chevy Lumina. When I turn on the AC, the compressor clutch does not engage and the fans do not spin. I was able to jump the compressor so the clutch engaged, however, the fans still did not spin and the AC was not cold. I then jumped the low pressure cycling switch (near the accumulator), which caused the fans to spin while the compressor was running. However, this still did not produce cold air from the AC and none of the AC lines were cold to the touch. I am starting to think the system is low on Freon, but I do not have gauges to test the pressure.
View 2 Replies
2006 Chevy Silverado 2500HD Duramax.
When I park it with the front end elevated even just slightly higher than the rear the fuel system loses pressure and I have to pump it up using the manual pump under the hood. This usually happens after 15 - 20 minutes of park time. When it is parked flat it usually will last hours or more, and if I park it with the rear elevated over the front then it doesn't seem to have a time frame. in other words it does not lose pressure at all.
View 3 Replies
I wait for the glow plug to stop before attempting to start. Then it's like Aaron Tippin sings, "sometimes she runs, sometimes she don't". It turns over fine. When it's running, it runs good. But most times it won't start. The fuel is being stopped somewhere. The in tank pump is working..I can hear it when I turn on the key. What else can I check?
View 5 Replies
Recently the check engine light came on and coded out to the mass air flow sensor. I changed the sensor and cleared the fault code, but after doing so the car wouldn't start. After many failed attempts to start the motor, I disconnected the positive lead at the battery and reconnected it a few minutes later. The car started and ran smooth, however the check engine came back on and coded out to the mass air flow sensor again...
I let the car continue to idle and disconnected the lead at the sensor how the motor would react; it continued to run smooth....I then reinstalled the old air flow sensor and engine continued to run great...So with all this said, car runs great when check engine is on and code is not rest, however, car will not start upon clearing the code and resetting the light......is it safe to assume the computer is going bad and needs to be changed?
View 7 Replies
Why will the 96 Blazer not start in the rain? Replaced almost all electric components from key cylinder to plugs. It is grounded somewhere when wet.
View 3 Replies
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
View 19 Replies
My 1996 Chevrolet cavalier will not start. It sat for two months while I looked for a neutral safety switch. New switch is in and brand new battery, Car does turn over. It gets close but no luck. I put new gas in. I really need to get this running before the snow flies.
View 1 Replies
I have a 1996 Chevy Cheyenne pickup with a fuel injected small block that has 50k miles. Earlier this summer the truck developed a problem where it is very hard to start when cold (after sitting overnight or after sitting for many hours on my flat driveway). When the engine is cold (say the first start of the day) I can only get it to start by giving small bursts of cranking power to the starter. That is, it won’t start if I hold the key in the cranking position but is more likely to start if I give it a short burst of cranking power (when I hold the key in “start” position) for a second or two.After the first start of the day, the engine runs fine and subsequent starts are quick and normal. The “Check Engine” light is not on and there are no trouble codes…. Other than hard starting there are no issues with engine performance.
View 2 Replies
I have a 1996 chevy cavalier 4-door. It is a 2.2 auto. I changed the passenger side cv shaft and now it won't start. I have lights it won't turn over. I put a new battery in no luck.
View 4 Replies
I recently purchased a used 2001 Chevy Blazer with a manual transmission. In order to start it, I have to push very hard on the clutch, almost through the floor. Is there some type of adjustment to make starting a little easier? Also, when I push on the parking brake, it also goes right to the floor and seems like it barely engages.
View 1 Replies
Just read the comsumer report "Annual auto issue", it reminded me the hesitation issue with the 2.0T (... page 70: We found the Passat hesitates slightly on takeoff from a rolling start..."). Is it a common problem with the turbo engines? it could be deadly when you change lanes on a busy highway.
View 7 Replies
My clutch is not disengaging when i push in the clutch pedal. I have good clutch pressure, I have to basically rpm shift my way through the gears. Is a dead slave cylinder the most likely culprit for this? if so is there any special information i need to know when it comes to bleeding out the new one?
View 1 Replies
1996 Ford Ranger 4-Cyl. 90,000 miles. 5 speed manual transmission. When the truck is driven 10-15 miles and heats up the clutch will seize in the up position. Once the engine is turned off then it can't be turned back on because the clutch won't depress. After the truck has completely cooled down the clutch and the transmission again work fine, as long as I keep any use under about 10 miles.
View 6 Replies
This is regarding my 96 BMW 328i. It has approximately 177,000 miles on it. Over the past year, I've replaced the cooling system, fuel pump, alternator and trans fluid for kicks. So, I'm understandably frustrated with it. Anyway, to my story:
On my way into work, whenever I pressed in on the clutch, it would make a loud clunk/pop and freak me out. I turned around after 1/4 of the way and swapped cars.
My mechanical skills are maybe 3 on a scale of 1 to 10. I'm not afraid of changing oil, brake pads, transmission fluid, changing an alternator, etc. But I want to have someone to blame for anything that involves anything within the engine block/head/transmission continuum.
I noticed that a heat shield was loose between the driveshaft and the exhaust. I rapped it with a hammer, and the heat shield didn't make a noise anything like I'm hearing. So, it doesn't sound like that's the real culprit here.
View 5 Replies
Sometimes in the morning the AC will work just fine, but after a while it stops working. It looks like the clutch will not engage and I don't know how to troubleshoot it. I'll take a picture later on today. I'm wondering which part is what, and what might be causing the problem.
View 9 Replies
I have a Mk4 1.8t , I left a light on and near killed the battery one night , was parked on a hill so I let it roll start.( I know this is where I went wrong so lets get past it....) It started in what sounds like some type of limp mode, dim dash lights and about 300-400rpm. cruised at about 10mph for say a 1/4 mile before the engine returned to normal rpm and lights returned to proper brightness.. now the car has a problem I cant seem to put my finger on. When it gets to about 3000rpms it bucks and begins to throw multi misfire codes making it hard to even get to 30mph.
It reminds me of how it felt when all the coils started failing but I know it cant be that because its all new , (plugs ,coils,) I have also replaced a few other easy parts such as the n75 and the diversion valve next to it, as well as the fuel pump and filter. One thing I noticed when I leave my n75 unplugged (wide open) it seems to run better making it easier to drive but if I go anywhere past 1/4 throttle it bucks and struggles. I've used the Autel to scan it for other codes but the only thing I get is random multi mis codes and mis codes for each individual cylinder.
View 1 Replies
