Chevrolet - S-10 :: 2000 - Loss Of Drive Power
Apr 6, 2012
My son has a 2000 S10 that runs alright as long as he only drives it about 20 miles one way, the problem seems to occur after he goes on longer trips, closer to a 45 or 60 mile drive, and it seems to happen when he comes to a stop, at a red light, or stop sign, the other day I drove it to my daughters house which is a 45 minute drive, we stopped several times, before I made it to her house, just when I though we were going to make it with no problems, I come to a stop at a red light, when I start to pull off the truck becomes so sluggish, that the truck motor can barely keep running, when I let off of the gas it seemed to pick up power, but every time I pressed the gas it would bog back down, I barely made it across the intersection, trying to get to a parking lot, when the power is just to low to pull any more, so I leave it running, but put it in park, so my wife can get behind the wheel, thinking, that if she presses the gas, while I push it, we can make it to the parking lot.
Well as soon as I got behind the truck, I tell her to put it in gear, and press the gas, while I push, well the truck takes off and she drives it in the parking lot, I walk on up to were she had parked, there was a burned rubbery, or oil smell coming from the truck, not should which, I’m checking everything out, when I take the power steering cap off, it releases air out of it, like there was press build up in it, after that I crank the truck back up, and drive it to my daughters house, and back home with no more problems, the check engine light came on when this happen, but has now gone back out, now, like nothing is wrong, what could cause this? I have check everything maintenance wise and everything is in good working order it doesn't run hot, it has the right oil pressure and amount of oil in it, has the right amount of transmission fluid and power steering fluid, I took it to a mechanic, but he said he didn't find anything wrong with it, and told me to just drive it, till what ever was causing this tore up.
View 4 Replies
Advertisement
I just noticed the 4 wheel drive on my 2000 Chevy S10 doesn't seem to be engaging. The traction doesn't get any better turning it on and the other day I got stuck on a hill and the back wheels weren't spinning. What I can check or look at to fix it?
View 1 Replies
I have a 2003 S-10 standard and a similar conditions as this discussion, but my issue is not with the engine bogging down. The engine RPMs increase, but the truck does not pick up speed until I let the engine settle, then push the gas again. If I drive too long the truck will start doing this in 3rd and not just when I shift gears. It's like the power is just not making it to the wheels. There's a disconnect in the power transfer or something.
The clutch (clutch kit), flywheel, master and slave cylinders, and the lines to the cylinders have all been replaced; some twice. I just had the transmission and differential fluids replaced. Is this a transmission issue or could this still be something to do with the clutch? Or is it something else entirely?
View 14 Replies
I own a 1988 Camaro Iroc-Z with a 5.7 350 TPI motor. I was driving the car onto I-95 at a speed of 65 when I heard a loud boom under my car, and pulled over to see what had happened. I couldn't see what happened, so I drove the car slowly to a friends garage to find the exhaust pipe from the converter back to the muffler had split and blew apart. I took my car to another shop to repair the pipe, but when I left the shop after the repair, I accellerated to about 40 mile per hour, I get another loud backfire and loss of power. The pipe is still intact, but I cannot figure out what is causing the backfire. My friend from the first garage says it is a failing fuel pump. I never heard of such a thing to be honest.I am at a loss and I have to correct the issue soon, as this is my only car to drive.
View 4 Replies
I have a 2000 Chevy Monte Carlo that has me stumped as to why it leaks. The driver side axle seal leaks fluid only after a drive. I have replaced the axle twice and seal 6 times and it still leaks. I am stumped on this one. Unless I got a bad axle twice that the diameter of the sealing surface is too small but didn't seem like it as the seal hugs the shaft.
View 4 Replies
My 07 2.0T (101k mi.) Passat idles roughly when in the drive position (at a stop light, or sign, etc.), the engine sounds "gruffy", and suffers from a slight loss of power with horrible gas milage. I've had spark plugs and the coil pack replaced two weeks ago, and still can't seem to find the source. There are no misfire codes or any others showing up. From reading many posts here, I've found that a common issue is carbon build up for similar symptoms of my car. Do I need fuel injector cleaner, and or valve stem cleaner, etc? As far as the possibility of cleaning out the intake valve, I only open the hood to add oil, washer fluid, check my oil, and wipe down the engine.
View 5 Replies
2002 Chevy Monte Carlo SS 6cyl 100,000 miles
Symptom, loss of horse power (from a stop and going uphill), surge or lunge forward when accelerating (misfire?), rough idle (occasional knock). Maintenance, regularly change all filters and fluids, recently had the m.a.f cleaned and changed air filter, spark plugs and wires, oil.
There have been times in the past year or so when the car would crank but not start. Especially when the car was hot. Wait a couple minutes and it would start. Also a couple of times the car would shake fairly hard when started, get up to speed and it was fine.
I have had people tell me anything from a clogged catalytic converter to bad fuel injectors or fuel pump.
Scanned the car last week. No codes showed up. Never had a Check Engine Light.
I forgot to mention that every once and a while the car will jerk when accelerating. I have a coworker who said his truck started to jerk forward and later would not start at all. Our mechanic said it was the fuel pump. I I will see what that does for him.
View 13 Replies
Driving while in 4x4 HI up a hill the truck started to slip. I stopped, shifted to neutral, and engaged 4x4 Low. I shifted back to drive and started moving up the hill. The engine started to lose power and the "Service Engine Soon" light began to blink. I put the truck in park. As I let it run a little bit, the engine started to shake as if something was very imbalanced. I went to check under the hood, and confirmed that it was shaking quite noticeably. There was no grinding or clattering of any kind though.
I turned the truck off for a bit, and then restarted. There was no light or shaking upon starting up; but as soon as I put it in gear and started driving I could tell it was losing power, the light came back on, and the shaking ensued. This occurred in 2wd, and both 4wd lo and hi. I parked it at a neighbors place and there it sits for now.
I plan to try and get the codes read. My other vehicles can't make it through the snow we have right now, but it is suppose to get warm later today and might melt enough for me to get one out. I also live out in the country, so the nearest auto parts place is about 20 miles. Same with a dealership service shop. I'm hoping I can buy and return a code reader from an auto parts store to assess if this is something I can diagnose myself or not.
It is the 6.0l gas engine with the 4sp automatic transmission. The truck also has about 107,000 miles.
View 16 Replies
The vehicle: 2002 Chevy Silverado 1500 w/ Z71.
The problem: Steerage issue. No problem exhibited while driving. However, at stop or very slow there is a loss of power steering but only when turning the wheels right. There is also an audible sound when turning to the right. Kind of a whooshing or air expulsion?
View 8 Replies
I have a misfire in the 6 cylinder on my 98 Chevy c1500 5.7l 350 v8 2wd. I changed the spark plugs and wires, cap and rotor, and changed the spider injector i put the spider injector in from another engine I had. After doing all this the code still comes up. The truck runs fine and except it idles slight rough not bad at all and now it says I have a vacuum leak and while I'm driving you can feel the loss of power. I tried all the ways to do it like on YouTube. What is wrong with my truck?
View 10 Replies
I have a 94 Chevy Suburban C1500 with a 5.7L, 350 Engine. It has 235,000 miles on it. I purchased it about 4 years ago with 191,000 miles in very good condition and obviously well maintained. I have continued to maintain it well.
For the past few months it has begun to start a little slower that before and when accelerating cold or warm there is a spot where it looses power. It doesn't sputter or die it just looses power. I can press the accelerator farther and it will come back to life and do fine. After a 20 -30 minute drive if I park for a while, 20 - 30 minutes, when I start it up it dies. The only way to keep it running is to give it the gas and smooth it out at about 1500 rpm for 10 - 15 seconds. Then I can drive it with no problem most of the time though it still has the dead spot on acceleration.
There is a good spray pattern from the throttle body injectors. Plugs and wires are relatively new and plugs look good (AC Delco Rapidfire Platinum). When I turn on the ignition without going to start, the fuel pump builds pressure for 4 - 6 seconds. I haven't checked the fuel pressure yet and am considering investing in the rig to do so. I recently replaced the fuel filter but that didn't work.
The check engine light has not come on but many of the lights in the cluster are burned out and I haven't felt like going to the trouble to fix that so it is possible that the check engine bulb is bad.
View 12 Replies
About 2 months ago, I needed to test my engine cooling fan motor. Was using two lead test wires with alligator clips and stupidly connected the battery ends first and then the wind blew the other connection ends together creating a spark. That may or may not have anything to do with what has happened since then. About 3 days after that, I started to notice that my lights were dimming and ac fan motor was slowing when the engine was under load as in 1st or 2nd gear or going uphill.
After about a week, the ALT/BAT light came on and I replaced my alternator. The problem with that was that getting the belt back on the new ALT nearly killed me and I got several pretty bad injuries and ended up having to get it done. The old alternator tested bad so I figured my problem was solved. But ever since then, I am still getting the same problem - a voltage drop or loss of electrical power causing the lights to dim and the fan to slow - except this time is doesn't happen under load - it happens while driving and just after I have come to a stop at a light or stop sign. I have had the battery and alternator tested several times and they always show up as being fine.
I checked all the cables and connections and changed the positive battery cable bolt. I get no codes thrown. I cant just take the alternator out and change it because of what I went through with the last one - not to mention it tests OK so I can't use the warranty as long as that is the case anyway. So I am left with this troubling, annoying problem and don't know what the cause or solution is. I am guessing the list of options has to have the alternator, battery, connections, belt (though I have no sounds or evidence there is a problem with the belt - I suppose if the tensioner was damaged with the belt fiasco that it might cause such a problem). What to do? It is the biggest problem at night because my headlights are affected.
2001 Cavalier 5-speed manual 2.2
View 5 Replies
I have a F350 that has intermittent power loss.
View 14 Replies
I pulled with my 2000 F250 7.3 for the first time yesterday pulling a 12,500 5th wheel and then again today with an 18 ft ski boat weighting around 3500 for both the trailer and boat. I had this same issue pulling both.
Today when pulling the boat/trailer i was behind a slow moving truck and when we hit a hill with a passing lane i merged over and wanted to start passing him. We started off at around 45 mph up the hill and as I started pushing the pedal I wasn't gaining any speed and my rpm's didn't even get over 1500. It felt like a stall and continued that at around 45-50 mph up the hill (about a 65 degree slope). When I'm not towing the truck runs great, plenty of power and averaging around 16 1/2 mpg.
Only mods i have is a 6647 Napa filter, muffler delete and it's running the same 4 position TS tuner from the original owner. During normal operation I run it at the 75hp gain and when towing i use the 50hp gain.
In both instances i could see black smoke coming from exhaust when pushing the pedal but my rpm's wouldn't go up and truck maintained the slow speed going up the hill. Once at the top it drove normal and picked up speed without any problems.
View 14 Replies
I've got a 2000 F-250 with a 7.3. The other day I was driving down the road and it lost power and my foot almost went to the floor. I was at the bottom of a hill when it did this and I was running 60 mph. By the time I got to the top I was running 20 mph and had the truck to the floor. When I was driving it home it was tacking around 1800 rpm and my egts were only at 125 degrees. I know I'm not getting fuel. I thought it could be the fuel filter so I changed it. Still no luck. It'll start back up but it dies if I take my foot off the accelerator. It shook terrible when I was driving it home too. Is it injectors, uvch, hpop, or something else?
View 14 Replies
What would cause my truck to have a long turnover start, a really rough idle, and a loss of power after idling at a stop light for about a minute?
This problem gets worse as the truck warms up. It feels as if I'm not getting power from all 6 cylinders but this goes away after about 20 feet of acceleration. The truck has never not started. It just has to turn over for about 5 to 10 seconds before it fires up. I changed the spark plugs and wires thinking it was that and then i tried the fuel filter and it wasn't that either.
View 8 Replies
I recently had the high and low pressure tubes on my power steering fail causing a total loss of fluid. After about a week of living with manual steering, I brought it in and had the tubing replaced. Everything worked fine, though the steering felt a bit sloppy to me. Today, on my way home from a 100 mile trip, the car decided that turning left just wasn't something it wanted to do.
So to turn left, I would have to back up and turn the wheels to the right. Not exactly an efficient way to drive in traffic. Do I try to get the car back into my mechanics place to see if he can fix it for a reasonable amount, or should just bite the bullet and look for a newer car? BTW when I had brought the car in for the tubing replacement, they showed me where the bracket holding the strut on the left had begun to crack, probably from driving without the power steering. 1998 Malibu LS ....
View 3 Replies
I have a 2000 gmc jimmy 300.000 km 4.3 vortec .starts ok, even when cold idle smooth but when I accelerate past 2000 rpm it has a complete loss of power. I bought a fuel pressure tester key on 2 seconds 60 psi when I start the vehicle and running 55 psi. I took it on a road test it stays at 55 psi and has a hard acceleration and will go to 60 psi ,and then starts to break up my first question is how can I block off the return line to the tank, there's no rubber hose in any of the connections just steel lines and hard plastic with push connectors, is there a plug that you can buy or how I can block off the return to see if the pump will build pressure to 75 psi to 80 psi will this will tell me whether the pressure regulator is faulty or the fuel pump needs to be replaced.
I have a manual its a Haynes for chevy blazer gmc from 95 to 2004 it says with central sequential fuel injections (csefi) key on engine not running it should be approx 55-61 psi the engines running at idle it should decrease through 3 to 10 psi according to this manual i am within range but i have read on other posts that it should be 60-65 would you say that my 55 psi reading is okay? or should it be 60-65? also when i blocked the return line should i get a reading of 75 or higher? if the reading goes up does that mean that the fuel regulator is faulty? and if it doesn't go up does that confirm that the fuel pump is the issue?
View 3 Replies
So, I have a 2000 Hyundai Accent that has had the CEL light on ever since I have owned it (about 7 months). I was told it was the O2 sensor and did not have it scanned. Occasionally, it would lose power and the CEL would blink. After I would take my foot off of the pedal and baby it for a sec it would usually go solid again and drive okay. About 2 weeks ago it started blinking constantly and it sputters and drives like sh*t. Now, I know that I should take it to Autozone or someplace so that they can tell me which cylinder is misfiring and all, but it is really sketchy to drive. I put NGK spark plugs in it today with no change. I ordered plug wires and a coil pack to see if that straightens out the problem. If it doesn't then I am going to lean towards intake gasket or perhaps a missing or bad o-ring at an injector. So, does this sound like a reasonable plan of attack to get rid of the blinking CEL (misfire) and restore my Accent back to all of its craptastic glory?
View 2 Replies
The wife was stopped at a light in her 2006 S60 and when the light changed and she accelerated the car stalled and died. It would not start and thus I had it flatbedded back to the house. Id been told at the dealer during a service trip ($$$) that the alternator might be going bad as it was making a whirring noise and was given an estimate to replace it, the serperntine, pulley, etc.. of $1300. At the time it wasnt a driveability problem and being a working stiff I didnt have the 1300 to spend so I decided against doing the work. Thus, when the car stalled I figured it would be the alternator causing the problem and draining the battery.
I recharged the battery overnight figuring I could get the car turned on then remove one of the battery terminals to verify faulty alternator. However, car would not turn over, Id only get what sounded like a click from the starter. Fine, I figured, the alt killed the battery so I went and purchased a new one and installed it. Car would still not start and Id still get the click from what I believe is the starter. Tried the old bang the starter with a hammer and still nothing. Checked the connectors to the starter and all seemed ok.
At this point, the dreaded "my wife seized the engine" thought popped in my head. I then tugged a bit on the serpentine and noticed the crank turn slightly so Im pretty sure she didnt seize the engine. (fingers still crossed on that one).
View 2 Replies
I have a 2000 Nissan Xterra 3.3L, at 114,000 miles I changed all the belts two days ago these being 3 serpentine accessory belts and the timing belt with tensioner. I do believe that the engine did not move (cams & crank) while replacing timing belt and even made sure the timing marks all lined up on the cams and the crank upon installation. The belt tension on timing belt was done to Chilton Spec. as well. I did not tighten the serpentines to spec. , but just to best judgment. Between idle -to- 3000 the engine does not seem as strong especially up hill. It idles smooth, does not overheat and there is no tapping/knocking or a check engine light. I was told that that with new belts (especially the timing belt) the motor may have to wear to the belts or vice versa and there may be some power loss till all wears in together do to now tighter tolerances. I was going to relieve some tension on the serpentines to see if maybe that would make a difference in regaining power.
View 14 Replies
