Chevrolet - Malibuclassic :: Distinct Clunk When Place The Car In Drive Or Reverse From Idle
May 7, 2013
What are the symptoms of a worn motor or transmission mount? I feel a distinct clunk when I place the car in Drive or Reverse from idle. I did not notice any problem when I bought the car few weeks ago. Before spending 300+ I checked for the problem one more time. The problem is that the clunk was all but gone. An intermittent clunk! What gives? The car is an '05 Malibu w/4cyl, 119k. The former owner had the transmission fluid changed at 94k.
View 1 Replies
Advertisement
I have a 2006 Chevy Silverado. After a complete stop a distinct "clunk" comes from the rear passenger tire. It's not heard or felt every time maybe 70%. I've raised the rear end and spun both tires to check for a sticking caliper. I haven't removed the tire. Brake fluid is full and in good shape.
View 2 Replies
I have a 2004 Chevrolet Malibu Classic with 173k miles on it. Car runs great. AC works intermittently sometimes, but it's not a huge issue. It kind of stops if your in city traffic, but at highway speeds, AC is dependable. Particularly when running AC (or it may just be because it's the end of summer), I notice a smell on my clothes. It's not necessarily like standing beside the exhaust pipe, but after driving for a while with AC, I notice it. I also sneeze some when this happens.
View 7 Replies
I have an 04 Chevy Malibu classic who recently decided she has to have the last word in every conversation: every time I use my blinker, she continues making the sound at her leisure, even though the blinker light isn't activated. [URL].................
View 3 Replies
I have a 1999 chevy malibu with a 2005 chevy impala motor in it. Recently I put my car into reverse and it made a hard clunk and went into reverse. Later on that day I tried to go into reverse and it will not reverse. I had to have 3 people push my car back in neutral. However, in neutral I am able to press on the gas and drive forward... This is an automatic transmission. Am I just screwed and need a brand new transmission?
View 12 Replies
I own a 2002 Chev. small blazer with 4 wheel drive available. Largest V-6 available. There is a clunk sound I can hear and feel as this vehicle is shifting OUT of 4 wheel into 2 wheel drive. Going from 2 to 4 wheel drive is perfect. First mechanic (test drove alone) said he would have to tear apart the front transfer case to determine fault. 2nd mechanic (with me along) did power brake slow turns in parking lot. Said the electric shifter was bad and would have to tear apart the transfer case also. Neither mechanic put the vehicle up on a hoist.
View 2 Replies
I have a 13 Altima and have been hearing a clunk/pop sound when coming to a stop and sometimes when changing from park to drive and park to reverse. It seems to also be there when accelerating too and the car is also seem to be vibrating when moving at lower speeds. Today i noticed something else. I parked the car and took the key out. I went to the side of the car and slowly rocked it back and forth and started to hear this clunk sound. I have uploaded it to youtube and can be found here [URL].... . After hearing the sound, I decided to take the driver wheel off and noticed it makes the same sound when i move the tires. It seems to be coming from the CV joint, where it connects to the transmission. why would a car make that clunk sound with the car/key off and swayed back and fourth? does this seem like a CV joint issue or something related to the transmission.
View 3 Replies
I have had a 2000 Chevy Cavalier 2.2 liter 4 cyl Automatic for about 5 or 6 years now. I have noticed the whole time I have owned it that when I start the car and shift from Park to Drive I hear a clunk and the with the hood open the engine pivots back and forth one time more than it is supposed to. This only happens from park to drive, it does not do this from park to any other gears, and once the car is in drive everything is normal. The car has no shifting problems at all, no slips or clunking while driving or hitting the gas real fast on take off.
I changed the all three mounts on the car yesterday. Upper engine mount (still in decent shape), lower dogbone (tore to hell), and Transmission mount (decent). I really haven't noticed it get any worse over the years I just know its not right. I have never changed the fluid or the filter since I owned the car, and most likely it has never been changed in the cars life. Could a dirty filter, and dirty fluid cause this problem? Or could the linkage need adjusted or replaced?
View 6 Replies
For a few months now I have been hearing a tap clunk type noise coming from under the car when I shift the auto trans into drive and reverse. Also sometimes when the car is slowing when driving I hear the tap sound as it shifts into first. I drove in by my local dealer and they listened to it and said Elantra transmissions can get noisy there is nothing wrong. They told me I have plenty of Warranty left so if something happens I will be covered.
View 2 Replies
What is the source of the sound? Listen for the clunk b/w 3 and 4 seconds. I just dropped off my 2016 Super Duty 6.7 CC LB 4x2 at the dealership. I'm afraid that they will say the sound is a characteristic but I never had the sound on my 2011 Super Duty 6.7 CC LB 4x4. This sound happens when I go from drive to reverse or when using the exhaust brake when towing. The sound does not exist when the transmission is cold only when it is fully hot. It will also make this noise when climbing a really steep hill in first gear with fiver and the torque converter needs to slip a little.
As far as I can tell all of the u joints are tight and the axial support is tight I only have 2000 miles on my truck.
[URL] ....
View 5 Replies
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 Replies
I have a 2006 Chevy cobalt and am currently stranded with my husband. Last night as we were about to head home from visiting family 3hrs away, we got off at an exit and as we were stopping about to go again because the light turned green, the car stalled. We had to start it a bunch of times just to get it to the nearest gas station about an eighth of a mile down the road. The message on the dashboard said "engine power reduced". We looked up that message online and a few posts said to disconnect the battery. We did that a few times but when we went to go, it kept doing what it did before, stalling. We were almost to the road and decided we weren't going to make it so we put it in reverse and it drove just fine back to a parking spot. Why it would stall idling and in drive but not in reverse? We are baffled and currently waiting on a tow.
View 3 Replies
My future mother-in-law has a 2004 Chevy Cavalier. Last night night when she tried to put it in gear, the car would not go in reverse or drive. She recently had a tune-up on her car a month ago and everything seemed to be working fine. I think the transmission is dead. Does that sound right?
View 8 Replies
My 99 Tahoe has started making a weird like clank noise when I shift into drive or reverse. It also has a light shake which was only if I took a sharp turn, but is becoming a little more common.
View 10 Replies
2007 Chevy Impala3.5L 6-cyl Flex Fuel engine w/ 4 speed auto trans52,800 miles
Extreme driving conditions maintenance schedule kept.Transmission standard service done @ 32,800 miles which was 20k ago.
PROBLEM:
1) Twice in past three days, when shifting from reverse to drive the transmission has slipped, revving hard with rpms spiked above 3,000 for about 2 seconds before engaging the forward drive gear.
Normally I come to a complete stop of all reverse motion with foot fully on the brake pedal before shifting. Admittedly, I got sloppy the first time noted and still had very slight reverse motion when I shifted.
2) Several times late today, while driving uphill at approx 35 - 45 mph, when the car downshifted there was an extremely brief moment of transmission slippage with spiked rpms. It was so brief each time that at first I thought I'd imagined it until it happened again. Then it did it once on a level surface in a parking lot when having shifted from reverse to drive without problem and was gently accelerating the transmission again slipped for just the briefest moment when the normal automatic shift point was reached. So far, all incidences while driving have been so extremely brief that it was the merest hint of a hiccup.
3) When bringing the car to a complete stop, such as at a stoplight or when parking, as the transmission automatically shifts for the braking of speed, sometimes there is a minor but noticeable thunk sound seeming to come from underneath the car, I'd judge to be somewhere about under the level of the dashboard or slightly forward of that. Could that be from a worn or broken transmission mount? And, if so, could that be somehow causing the slippage problem?
4) This transmission has always, even since new, allowed more roll after being shifted into park, the engine shut off and my foot taken off the brake than any other car I have ever driven. If I forget to engage the parking brake quite tightly, the car will roll forward quite a few inches before the parking pawl holds it, even on the level. I've been told both by the dealership shop and the independent mechanic shop that there is no problem and that this particular engine/transmission combination tends to do this although my particular car seems to do so somewhat worse than average.
ACTIONS TAKEN SO FAR:
1) Have made an appointment to take the car into the mechanic.
2) Will check the transmission fluid level per instructions in the owner's manual tomorrow when I have daylight to see what the fluid level and color on the stick looks like.
NOTE:
1) I periodically check the transmission fluid level and it has never been low or discolored. The shop checked it for me, along with making sure everything else was road trip worthy, for an emergency 1,000 round trip in late November, just three months ago. No problems then.
2) No evidence on the garage floor of any leakage. Garage floor is dry.
QUESTIONS:
1) I presume the first step is for the mechanic to check the fluid level and examine for any leaks?
2) If the mechanic cannot duplicate the problem in a test drive, then what?
3) If the problem cannot be duplicated and no apparent cause found, I presume that the prudent course of action is to go ahead and have standard transmission maintenance done (i.e. drop the pan, check for debris, drain and replace with fresh fluid) then see if that halts the slippages?
4) Given that this car has already had failures of the power steering pump, water pump, and part of the wiring harness, and has a fuel pump starting to get noisy, despite aggressively maintaining all standard/preventive maintenance, that perhaps it is time to think of replacing this car, especially if there proves to be any truly major transmission problem found?
View 19 Replies
I have been driving a 2003 Chevrolet cavalier and the automatic shift is stuck and can only shift to neutral and drive since Thursday morning. It wont go up to reverse and parking and down to the other 3 shifts.
This first happened last April but somehow with the right grip or pressure was able to get back to all the other shifts. Since then it happened 2-3 times as I can remember and now could be getting worse.
View 1 Replies
A coworker has asked me to take a look at their 2013 Camry LE, 48,000 miles. It has a quite annoying vibration at idle and only when in reverse or drive. AC is not running this time of year, but does get worse if the compressor is turned on.
I'd like to think the trans and engine mounts are fine. It does not have any noticeable torque converter shudder. I have cleaned the throttle body, not that dirty, but not much improvement.
I suggested that he try different brands and grades of gas to see if matters improved at all - Shell 89 seems to be a slight improvement over what is normally used (just 87 from Costco, Sunoco, or Hess), but nothing substantial.
Spark plug change, decarbonizing top end?
Spark plugs look about like I'd expect an iridium plug to at these miles - no signs of oil burning, not tons of carbon, etc. I didn't get a real good look at the piston tops.
View 7 Replies
I have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
View 14 Replies
Do a 2004 Saturn view front wheel drive transmission will fit in place of an all wheel drive...
View 1 Replies
I think I resolved the idle issue on my 2009 Corolla S with 82,500 miles and Automatic Transmission.
Symptoms:
Idled at between 600 and 800 rpms
Annoying vibration in drive and reverse, no vibration in park or neutral
On hard stops, the engine felt like it was going to die
Turning on the a/c would cause the idle to increase to 1000 rpms and the vibration would go away.
At 82,500 miles, I cleaned the throttle body which was extremely dirty.
Process:
Disconnect the positive battery cable
Remove the top of the air box and flex duct going to the throttle body
Disconnect the two coolant lines going to the throttle body, make sure and have a few old bolts to plug the lines so you do not lose too much coolant
Remove the electrical connector to the throttle body
Remove the vacumn line to the valve cover
Remove 2 bolts and 2 nuts (10mm) securing the throttle body to the intake.
The throttle body does not have a gasket, it is an o-ring which should be fine.
Once you have the throttle body off of the engine, clean it thoroughly with Chemtool throttle body cleaner.
The inside of the throttle body and throttle plate should look like shiny milled aluminum. when done.
Spray chemtool into the two ports where the antifreeze lines were connected. If possible use compressed air to blow out these ports.
Clean the inside of the intake and the mesh screen where the throttle body bolts to the intake.
Reassemble, connect the battery, crank the engine and just let it idle for a good 10 minutes
The 2009 Corolla S DOES NOT have a serviceable IAC. It is riveted on to the throttle body. This is why it is important to spray the cleaner in the antifreeze ports in order to clean it. These ports are the antifreeze bypass ports.
View 2 Replies
Sometimes when my car as sitting at an idle in either drive or reverse the motor starts to make a knocking noise from the back of the motor towards the firewall side on the top of the motor. I have a video. The car has 114k I just changed the oil I thought maybe it's low but it's not and hasn't moved since it was changed.
View 4 Replies
