Chevrolet - Lumina :: 1995 - Have Anti-lock Brakes?
Oct 5, 2011
How do I know if my 1995 Chevy Lumina has anti-lock brakes (ABS)???
View 2 RepliesHow do I know if my 1995 Chevy Lumina has anti-lock brakes (ABS)???
View 2 RepliesI have a 2000 silverado. When I come to a stop, sometimes the anti-lock brakes will kick in. it makes that all too familiar grinding/clicking sound that I hear all winter. However, it is happening during the summer/fall. It doesn't happen every time I brake. It seems to happen most when I am coming to a stop on an uphill or downhill grade, or when I am stopping while turning. It doesn't happen the whole time while braking, just right at the end before the vehicle stops. It also seems to happen more frequently when it is warmer out. The tires don't skid while it is stopping either, which I guess is supposed to happen. It is a concern since it does take me a bit longer to stop when the anti-lock is going, and I never can predict when it will happen.
View 3 RepliesGot no heat in my 1995 Chevy Lumina passenger car with 3100 engine. Have replaced thermostat, water pump and replaced freeze plug that had a pinhole in it. Heater still blowing cold air and temp gage only moves slightly - stays in low range never reaches normal operating temp. what's causing the problem and how to fix it?
View 9 RepliesMy anti-lock brakes keep activating when i am slowing down from a speed above 10 mph once i reach a mphh. I have just installed koni sports on the front and bg springs all around with 20mm wheels spacers in the rear. The sound is coming from the driver side wheel and i can feel the brake pedal reacting in the way it does when the anti-lock brakes are activating. I haven't had a chance to take the wheel back of and check the sensors and wires.
It makes a grinding and popping kind of noise, which again remind me of anti-lock brakes.
Two days ago, I brought my 1995 Chevy Lumina to my repair shop I've been doing business with for years...they replaced an A/C compressor, oil change and flushed the sludge. Now today, this morning, I crank it up and the steering wheel is almost impossible to turn...making it almost impossible to drive and unsafe to attempt. My plan is to call them tomorrow and have them tow it and inspect...another expense. This car has been a fabulous 2nd vehicle with 155K miles on it...I'd like to keep it, but might have to exercise other options if the cost/benefit ratio is out of whack.
View 15 RepliesI have a 1995 Chevrolet Lumina with about 175,000 miles on it. I've noticed in the past few months that the lights seem a bit dimmer, and the turn signal doesn't always work for the rear blinkers. It blinks rapidly in the front, but after a nudge to the turn signal, it slows down and begins to work in the back. Within the past couple of weeks, when the turn signal is on, it causes the speedometer indicator to pulse with the signal.
I took it in for the low lights and the signalling issue, and they said it might be the battery since it wasn't giving at a full charge. That was replaced, and the issues were still there. After that they said it would be an issue of getting into the steering column which would be a couple hundred dollars just to try and find the problem, but they couldn't guarantee that would actually find the problem.
I recently had my wheel hub and bearing replaced. The mechanic said I might hear a little noise with the brakes but they'd work. Turns out that noise is the Anti-lock braking system engaging every time I use the brakes. It happens when the car speed gets low, maybe 5-15 mph. Also, if I'm driving slow in a parking lot or something, and let off the gas, that change in speed sets the ABS system on too, without my foot being on the brake pedal.
I've also noticed sometimes when the weather is very cold, the ABS light will go on and the ABS brakes won't work; just regular brakes. Is this something that I'd be able to solve at home? Could I possibly bleed the brake lines to check for any air ( although braking seems fine ) , busted fuse for the system, anything else to check before asking the mechanic?
I woke up and drove to a stop sign. When I tried to pull away the transmission raced like crazy, HIGH RPMS! But was barely moving. After about 8-15 mph it would finally catch 2nd gear. I check fluids frequently, and topped it off a few weeks ago, and when I finally got where I was able to stop, I looked and there was no fluid registering. So I put 2 quarts in to fill.... Then started the car and it would not go into any gear completely. I'd just feel a small thump, when I shifted. It will actually drop into gear after a while going straight, but it's stil revving HIGH and it won't completely go into reverse. Weirdest thing, the "Anti-Lock" light came on while all this was happening...
View 3 RepliesI have a 2011 F350, with a 4 inch Rancho Suspension lift. Ever since the lift kit was installed, more commonly when turning to the left than right, the anti lock brakes come on and the traction control light comes on/flashes. without even stepping on brake pedal.
It seems to happen when the wheel is at about 80% of max turning, about 15mph. Both wheel hubs and sensors have been replaced. road tested with Ford tech , he watched the speed sensor input while hooked to the computer and all sensor are reading correctly.
Today I went in a constant circle and can make it do it non stop, and when you try to press the brake pedal while the anti-lock (grinding/chattering) noise is happening, it only gets louder.
I have a '99 E350 van that I am feeling a light anti-lock brake pulse in the pedal when I am rolling to a slow stop under light braking. Braking doesn't seem to be affected, but it doesn't feel right. I tried locking up the brakes and didn't feel any anti-lock pulse...seems backwards.
View 1 RepliesThe anti-lock alert indicator of my 2000 Buick Century goes off and on every day or so in warm weather; seemed that it stayed on much longer in cold weather. Braking is fine, no other alerts associated with braking. Is this a common problem? Might this be oxidation on terminal connectors of wheel sensors since it's so intermittent??
View 2 RepliesI have a 2004 Explorer that the anti-lock brake light comes on. Brakes work fine. What to look for first ?
View 4 RepliesI have a 1995 lumina. Yesterday the oil light came on. There is plenty of oil but the light stays on. I'm thinking it is either the oil pump or the sensor. How do I determine which???
View 14 RepliesMy anti lock warning comes on after 1 mile of driving. If I test the anti lock on ice during the first mile the system works fine, around 1 mile the lamp lights.
View 7 RepliesI was driving my Dad's Camry in the rain and at one stop I heard what sounded like the anti-lock brake noise and vibration. Heard it again when stopping on leaves. Didn't think much of it until I started noticing the same noise when the road was dry and clear. All the stops were gradual, from under 30 mph. The car stops fine, less the noise. I hear the noise approx 1 stop of 3 or 4 regardless of road conditions or weather.
What's the cause? Since it relates to the braking system is this something I should have the shop look at asap? This is a 2005 but with under 60,000 miles. Has been well maintained.
1995 Lumina LS 3.1L w/ ~185K mi
A few weeks back, the amber ABS light would periodically illuminate and then became more frequent until it was On every time I used the car. The light only comes on after driving the car forward ~10-20ft. Recently in the past few days, the red brake light also started coming on at the exact same time as the amber ABS light. I can start up the car and idle, backup, and then as soon as I drive forward 10-20ft., both lights simultaneously illuminate, along with the sound of something that is engaging/closing/switching etc. coming from the front driver's side, maybe where the brake module is located. The sound coincides with the illumination of the lights. There is also absolutely no noticeable difference in braking.
I just changed the oil a couple days ago and the fluid level was good and appears to have not moved at all since I flushed the lines ~2.5yrs. ago. I cannot recall if I returned the pistons to the home position back then, but either way I was able to bleed all 4 lines.
What may be causing both lights to illuminate together when the car moves forward in addition to coinciding with a sort of clunking/engaging noise coming from the front driver's side?
If I have to replace the EBCM, then do I need a scan tool?
I already called Module Master and they do not rebuild any GM EBCMs built before 1999. Looks like Rock Auto has some though.
My brother's 1995 chevy lumina 3.1 engine has been dying while braking for a stop and while reversing. Has replaced fuel filter, map sensor, throttle sensor, o2 sensors and still no change. He says he doesn't believe a tune-up is the cause either.
View 8 RepliesMy 2000 Ford Ranger 4x4 truck's anti-lock braking system is not working properly. When I slow down for a stop my anti-lock brakes kick in every time for about 1 or 2 seconds. What can I do to stop this from happening.
View 2 RepliesWell I have a weird thing going on with the anti lock brakes. Its normally more noticeable when its cold. Coming to a slow stop you can feel the anti lock brakes pulsing slightly or more noticeably if you hit a bump braking at slow speed. The only mods to the truck are 285/70/17 inch tires and a leveling kit. Not sure whats going on with it, but i thought i should check here before getting my wallet lightened by the dealership.
View 2 RepliesI have a 5.0L with around 144k mileage. I noticed a reasonably severe leak of anti-freeze the day after I had the oil changed at a shop (coincidentally?); nothing out of the ordinary on that day. The temp's have never showed as being beyond normal. I saw that there was a bit of weeping from the water pump, so changed that believing that the gaskets might be the real culprit (third pump on this truck). I re-filled the system with fluid (green silicate as the system had been modified several years back), ran the engine, and found that there is still a leak, not as severe, but most definitely bad. It honestly appears to be dripping at the oil pan gasket, just left of the crank on the lower end. The location doesn't really seem logical to me.
View 4 Replies1995 Chevy Lumina 3.1L Sedan with ~182K mi
Over the past 6 months, I have noticed fuel odor just about any time I turn off the vehicle, and I am also experiencing progressively higher levels of fuel tank pressure each time I remove the fuel cap. The fuel tank pressure seems to be greater the lower the level of fuel in the tank whenever I remove the cap. 6 months ago (~Sept) it was only a slight "hissing" periodically when removing the cap to fuel up, but now it occurs at every fill up and seems to have enough pressure to push the cap entirely off had I not been careful to slowly loosen the cap to relieve the pressure.
The entire fuel pump and sending unit assembly in addition to the tank and filter were all replaced about 4 years ago in May 2010 or about 28K mi ago. The issue has just come up progressively over the last 6 months.
Today, I inspected the evap. emission components and lines from the tank to the canister to the purge solenoid mounted on the rear of the engine. All lines are connected and seem to be in operable condition. The line from the canister to the purge valve mounted on the engine is completely free with no obstructions. I blew out the line with compressed air and absolutely no exiting particulates were observed. The lines on the bottom of the canister did not show any signs of wet fuel and there were no carbon particles present in the lines from what I could tell from disconnecting and inspecting. The vapor line from the tank to the carbon canister is not kinked or pinched in any manner.
I believe there is a fuel vapor check valve that resides inside the tank connected to the fuel pump assembly/sending unit. This was all replaced as a single unit as mentioned above. I am thinking this check valve may not be functioning properly and not allowing the vapor to escape into the carbon canister. I tried to apply slight pressure and vacuum on the vapor line connected to the check valve on the tank but no air was able to move in or out even with the gas cap off. However, I do have a full tank of gas right now, so I imagine the check valve will be closed.
The check engine light is not on but since this is an OBDI vehicle I am not sure there are any evap. emission codes anyway.
How can I test the gas tank vapor check valve? How can I test the vapor purge solenoid located on the rear of the engine? What malfunctioning component could be causing the excessive fuel tank pressure.