Chevrolet - Equinox :: 2010 - Running Rough And Stalling When Idling
Mar 31, 2013
I have a 2010 Equinox with about 52000 miles on it. At about 48,000 I took it in for the 50G maintenance. The car ran with a fluttery sound that I did not really notice until it was brought to my attention. Recently the car began running rough and stalling when idling. there were no warning or indicator lights lit. I had OnStar run a remote diagnostic and they said there were no codes. The day after the diagnostic the check engine light went on , while at the same tie the rough idle and stalling went away.
I brought the car in for service at the dealer. They said that the car had several codes indicating low oil and the car was down 2 quarts but there was no leak. They also said the noise I heard was the timing belt. The noise is gone after the service and the car is running smoothly. Coincidentally, or not, I got a notice from GM saying they were changing the oil monitoring software on the 2010 Equinox to recommend me frequent oil changes.
1) What could cause the car to loose 2 quarts of oil over less than 6000 mile? Is this normal or an Equinox problem.
2) Would low oil cause the timing belt to make a noise.
3) Do I have a lemon and am I being ripped off y the dealer?
View 19 Replies
Advertisement
My 2013 Chevy Equinox has 30,000 miles. When the car runs with the air conditioner on, it has a whining sound that goes off when the A.C. is turned off. I have taken it to my local dealer several times, and they say that the whining is normal for this vehicle. They also say that Chevrolet will not authorize a repair under warranty for this problem.
View 2 Replies
I have a 2005 Chevy Equinox with 73K miles. When I first start it up morning the car runs rough for about a minute or two and then smooths out. I took it to a mechanic who said there was oil on one of the plugs and to get rid of the car. I tried another mechanic on Craigslist and he replaced the upper plenum gaskets. It ran better for about a day or two and now the problem has resurfaced.
View 2 Replies
My Equinox had problems from when I bought it used at 23K miles. The evap hose recall was installed wrong and broke. The traction control went out and shut down my car in mid-drive (twice). Computer modules went bad. Timing chain had to be replaced. Then is was using 3 or more quarts of oil before reaching 3000 miles after an oil change, with no puddles on the ground. I received a letter from GM after it reached 120k miles, but the dealership was good enough to replace the whole engine anyway due to "problems" with this year and model. The catalytic coverters were bad at the time but not replaced though the "disappearing oil" from the bad engine seems to have caused that. What can I do to get this resolved without having to spend $1500-$2000 of my own money, that I don't have right now? (oh, one wheel hub assembly has just gone bad too)
View 5 Replies
I have a 2010 Chevy Equinox and I hear a pinging noise when my car is idling and when I drive below 40m.p.h. It sounds like a diesel engine, when it isn't. I have the 2.4L Ecotech direct injection. The dealership says this is normal, but why is it so noisy. What if anything can I do about the noise or is there a problem with the Equinox?
View 4 Replies
I have a 2001 7.3 ford the seal in the turbo went and oil went in the exhaust. lots of oil like 10 quarts. I had a rebuilt turbo installed ran great for 2 weeks then one day out of the blue started idling rough and then downward from there no power stalling etc I have my super chip scanner it read dtcs of 1249 478 1211 and 238. Is it possible the muffler is plugged with oil? or is it and ipr? 193000 miles....
View 3 Replies
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
My 2010 Accent has been stalling intermittently, always when I am idling. I'll be at a stop light, and it will stall, and then it usually starts right up again. It is almost always the same stop light on my way to work, like clockwork, and likewise on my way home from work. Also, sometimes right after this stalling event, the motor will be a little rough on the highway, sputtering like it's not getting gas very well, but then it evens out after a while.
Yesterday for the first time it died and wouldn't start again. I suspected my fuel pump had gone out. I had it towed to a repair shop, but it started just fine for them and they can't re-create the problem. It doesn't give any computer codes at all.
View 3 Replies
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
View 3 Replies
I just got my first dub, and it is a project car. I have had it serviced and it still idles rough when in drive with foot on the brake but idles normal when in park. a
View 2 Replies
I have a 1994 V6 Chevrolet Camaro with ~197K miles. Recently I have noticed that after starting the engine it idles rougher than normal and also as I accelerate, especially between 45 and 65 mph. Several things have just been replaced and/or fixed: spark plugs, spark plug cables, oil, coil packs, water pump, & thermostat. I regularly use premium gasoline and when for some reason a lower octane is used I add an octane booster. Since this problem arose I tried a fuel system cleaner; it hasn't worked thus far. The last time something like this happened, I took my Camaro to a trusted repair shop and when being diagnosed its' cylinder chambers and many different lines flooded with fuel. After replacing the fuel regulator my car returned to normal.
View 4 Replies
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
View 19 Replies
I was told that my 1997 kia Sephia needed a new catalytic converter by a very reliable shop. My car had been stalling out and running very rough. They did replace the distributor cap which seems to have increase the overall performance and that same day i had a smog check and passed with flying colors! Why would I still need to replace my converter if I passed smog. My car has only 36k on it.
View 19 Replies
My 09 corolla is running rough when idling in drive. It doesn't happen in park or neutral.
View 5 Replies
ok,up to yesterday, my wife's car started and ran fine. but we had not driven it in about 3weeks, and it was on empty. well, my kids would listen to the radio and, i think, starting it while we were at work. anyway, they ran it out of gas. so put gas in it, 3gallons, turned the key on and off a couple of times to get a good prime. started it up, died, i figured not enough fuel, yet tried again. started, but started spitting and sputtering and idling really ruff, had to hold to the floor to keep it running. removed the maf. it started and did the same. finally, i held down the gas and brake at the same time, took off to the store, got gas, but it died half way there. got it to the pump, put more gas thinking that's the problem. nope, the same. got it home, but when i let off the gas, it idles like it's not getting fuel and dies. so, any clue what it is? remember, 3 weeks ago it ran fine.
View 1 Replies
My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........
2003 Sante Fe, LX, 3.7 l engine
View 6 Replies
I'm having issues with my 2004 Toyota Corolla with 118K. Every few weeks, the car will go through a phase where it will stall out, run rough and hesitate on acceleration. Oftentimes it is accompanied with the rotten egg smell coming from the catalytic converter. When I decelerate to a stop light, the car will stall. When I start it back up, I have to rev the engine to 2000 rpm in neutral to keep it from re-stalling. Once I get up to about 10-15 mph, the car will jerk and sputter, and at 40mph, the jerking motion gets worse. If the car doesn't stall it'll run rough and have the rotten egg smell. I'm assuming the smell is from unburnt gas.
I find it happens more often when I don't let the car warm up for a few minutes. I've taken it to my mechanic, and i've gone through 2 MAF sensors, cleaned the throttle body. I changed the iridium plugs at 102K and am on top of maintenance with filters, oil and such. Of course when I bring it to the mechanic, the problems don't show up, and we are kinda blind to what could be causing the issue. Also, if I park it for a day or two after the issue occurs, the problems go away. What to look for?
View 8 Replies
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 Replies
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
View 6 Replies
