Chevrolet - Equinox :: 2010 - Replacing Engine And Catalytic Converters?
Nov 25, 2013
My Equinox had problems from when I bought it used at 23K miles. The evap hose recall was installed wrong and broke. The traction control went out and shut down my car in mid-drive (twice). Computer modules went bad. Timing chain had to be replaced. Then is was using 3 or more quarts of oil before reaching 3000 miles after an oil change, with no puddles on the ground. I received a letter from GM after it reached 120k miles, but the dealership was good enough to replace the whole engine anyway due to "problems" with this year and model. The catalytic coverters were bad at the time but not replaced though the "disappearing oil" from the bad engine seems to have caused that. What can I do to get this resolved without having to spend $1500-$2000 of my own money, that I don't have right now? (oh, one wheel hub assembly has just gone bad too)
View 5 Replies
Advertisement
My mechanic tells me that the hold up or carrier bearings on the drive shaft of my 2005 Equinox need to be replaced. He says that about half the time this cannot be accomplished and that I might have to replace the entire drive shaft. From the research I have done, it seems that a press (?) and blow torches are needed to replace the bearings. I can't afford the new drive shaft, but I could afford to replace the bearings if I could find someone who was sure they could accomplish this.
View 8 Replies
I recently went to my mechanic after living with a very small leak right between the catalytic converters and the transmission for about 4 months. (it dropped a dime-sized mark about once every 5 days.) he said it was the rear output seal on the transmission but wouldnt touch it since there was no easy way to get to it and didn't want to drop the whole exhaust system. so off to vw dealership (wow, i guess a lot of people complained because they replaced everyone there and they're more friendly and efficient. my car usually sat there for 3 weeks before they even looked at it. (appointment mean nothing to those people.) but after dropping off my car i got a call within an hour telling me it was a cracked ventilation hose. they ordered the part and repaired it within a week (another first.) i also had them change the trans fluid and filter and the car ran smoother and a lot better and i checked for 2 weeks for leaks and none were there but within the past week, it's back and leaking the same way. the puddle is about the size of a penny so back to vw on monday.
View 1 Replies
'05 GLX, 55k miles. Got an MIL light last week and it showed a P0421 code. Took it to the dealer and they replaced the right bank catalytic converter. That was last Friday. Fast forward to Weds. of this week. MIL comes back on and mileage drops noticeably, but power doesn't seem affected. Back to dealer, they end up replacing the other cat. Does this seem normal? I'm trying to figure out what may have led to this. Car is basically stock. I do my own oil changes (never overfill) and swapped out the spark plugs at 45k miles with Bosch Iridiums. [IMG] [URL] .....
View 4 Replies
The catalytic converters are very hot and the one upper left, when looking into the engine, is even red. The engine runs less than 10 minutes a the converters become very hot. I think when the engine run another 30 minutes, then I have a firework.
And that's not all. If the engine is idling, it's everything o. k. But if accelerates over 2.500 RPM, then it smokes as a locomotive. The smoke is white, dense and it smells like unburned fuel.
So I ask, are the converters blocked and I need to change them, or is the engine before death?
View 15 Replies
The vehicle is a 2001.5 Passat 4 Motion V6. 120,000 miles on the Passat.
The original Cats were replaced 1 month ago after a service station deemed them dead. When the vehicle failed emissions.
The codes were p0430 and P0420 and P411.
Before that about a year ago The O2 sensors were replaced.
After 2 new catalytic converters were installed. The vehicle is still throwing p0420 and p0430 codes.
View 4 Replies
I have some rust building on the heat shield of my cats on my 2001 Nissan Frontier.. I had a weld done to keep it from rattling after replacing the OEM muffler. It there anything I can put on it to retard the rusting process on the shield and will that affect my emissions?
View 4 Replies
My son-in-law has a 2006 Honda Accord with over 160,000 miles on it. About 8 months ago, the check engine light came on. The code said the down stream oxygen sensor was bad. He took it to a Honda dealer and they replaced the sensor and now the check engine light is back on with the same code. Can the catalytic converter have gone bad and can it have made the oxygen sensor go bad too?
View 5 Replies
Getting multiple CEL's for the catalytic converters and cylinder misfires. Looking for threads that address these particular codes ie. 0431, 0421, 0300. 0303, 0306. I have a feeling that these are being caused from a vacuum leak and/or needing a reflash for the ECU.
View 3 Replies
I have recently picked up a 2005 F350 with the 5.4, which has 212k on it. Has a check engine light on for P0420 and P0430, as well as some kind of a 'ignition coil 'D'', I forgot which code it was as I deleted them at first to see which would come back. After driving it, the P0420 and the P0430 came back, but not the other, yet probably. I'm guessing the misfire due to the ignition coil caused the cats to go bad and the 420/430 codes, unless these codes are coincidental and the cats went due to high mileage.
Either way, I'm pretty sure I will need to replace the cats and was wondering what is the cheapest route. Should I get individual cats and have a shop weld them on? Should I go to Advance Auto parts or Auto Zone and get the whole pipe with the cats attached to them already and then get them installed? I anything will involve welding, I would have to bring it in to a shop. Also, in regards to the ignition coil misfire, what a good way to check which one it is?
View 4 Replies
I have a 2010 Equinox with about 52000 miles on it. At about 48,000 I took it in for the 50G maintenance. The car ran with a fluttery sound that I did not really notice until it was brought to my attention. Recently the car began running rough and stalling when idling. there were no warning or indicator lights lit. I had OnStar run a remote diagnostic and they said there were no codes. The day after the diagnostic the check engine light went on , while at the same tie the rough idle and stalling went away.
I brought the car in for service at the dealer. They said that the car had several codes indicating low oil and the car was down 2 quarts but there was no leak. They also said the noise I heard was the timing belt. The noise is gone after the service and the car is running smoothly. Coincidentally, or not, I got a notice from GM saying they were changing the oil monitoring software on the 2010 Equinox to recommend me frequent oil changes.
1) What could cause the car to loose 2 quarts of oil over less than 6000 mile? Is this normal or an Equinox problem.
2) Would low oil cause the timing belt to make a noise.
3) Do I have a lemon and am I being ripped off y the dealer?
View 19 Replies
I have a 2010 Chevy Equinox and I hear a pinging noise when my car is idling and when I drive below 40m.p.h. It sounds like a diesel engine, when it isn't. I have the 2.4L Ecotech direct injection. The dealership says this is normal, but why is it so noisy. What if anything can I do about the noise or is there a problem with the Equinox?
View 4 Replies
I bought this truck (2011 F-350 6.2l) used a month ago with 125000 miles on it. Of course the MIL light came on as soon as the ink dried. The codes read PO420 & PO430 and my local Ford Service said replace the cats. I said what is the cause of the failure, ford said here is a list of possible causes but it's not reading other codes so they don't know what caused the failure.
Well, I went ahead and replaced both catalytic converters, all four O2 sensors, and I replaced all sixteen spark plugs. Guess what, the MIL light is back on not 24 hours later reading PO420, PO430, and now PO620 and PO645. So I just went back to Ford today and all they did was cleared the codes and told me to call if the light comes back on. They said my PCM is up to date but why it's now reading GENCOM code or AC Clutch code.
View 2 Replies
I have a 2006 equinox with 74000 miles that consumes up to 2+ quarts of oil every 2000 to 3000 miles between oil changes and the water in the fluid section of the car drops about one gallon of water thus causing the car to over heat what could be the problem. The engine light always comes on when i have more or less then 1/2 a tank of gas. The manual said this could be the gas cap that is producing the problem and is there a solution.
View 8 Replies
I bought a 2012 certified preowned Chevy Equinox with 50,000 miles. After I drove it for 3,000 miles I had to take it to the dealer due to an engine noise which turned out to be a low oil level. They changed the oil and then told me that it's normal for these engines to burn a lot of oil. I drove it for 2,000 miles after the oil change and the oil level was low again. I took it back to the dealer and they topped off the oil and told me to come back after 1000 miles for an oil consumption test.I don't know much about cars but burning through that much oil does not seem normal to me.My question is, how can I make the dealer take responsibility for this car oil issues while it is still under warranty?Is it normal for these engines to consume high amounts of oil and for me to keep replacing about 3 quarts every 3,000 miles?
View 4 Replies
I have a 2009 Chevy Equinox with a little over 50,000 miles. About a year ago the key began sporadically getting stuck in the AUX position when I attempt to turn the engine off (no problems when starting engine). The dealer installed a new ignition cylinder (which cost me $1,000) but the problem continues. When the key sticks I re-start, re-shift and re-brake and I can remove the key and turn off the engine on the first or second try. The dealer suggested that I take my foot off the brake when I remove the key but I usually have to FLOOR the brake to remove the key.
View 3 Replies
Recently I've been having some intermittent trouble starting my 2008 Chevy Equinox LS. The problem only occurs when I leave my daughter's daycare after dropping her off in the morning...so it's the second start of the day, after about a 5 minute drive. All other times the car starts fine. Here's a rundown of the symptoms:
-May 9th or 10th: I tried starting the car (at the daycare) and the engine made sort of a buzzer sound, and didn't start. Then, after a few seconds, I tried it again and it started right up.
-May 11th: I did some interstate driving (about a 1.5 hour trip each way). On the trip up, after about an hour or so, I received the following warnings: "Service Traction Control" and "Service Stabilitrack." After I turned off the car the warnings have never come back on (don't know if this is related to the starting problem, but figured I would mention it).
-May 18th: while sitting at a stoplight, the car was idling roughly - I had to really hold down the brake to prevent the car from lurching forward, and the RPMs were going between about 800 and 1500...haven't noticed any rough idling since, though.
-May 20-24 & 27-29: Again, when leaving the daycare in the morning, when I try to start the car, it sounds like a machine gun. It usually won't start the first time, but will the second time after still making that noise. Attached is a video of this. The odd thing, though, is that it hasn't done it the last two times I've left the daycare (I doubt the problem just fixed itself).
View 7 Replies
My truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 Replies
Our 2008 Equinox with roughly 90K miles showed the "service stabilitrack" warning on a Friday, next day light was still there now paired up with "check engine" light. My husband did something to the "stabilitrack" button which made both lights go away for a couple of days. Then both of these returned. Took the vehicle to the dealer (we always do for service, we just don't know some good mechanics in our area and so far we had not had any major issues with the vehicle).
They tell my husband it is the EGR valve that supposedly needs replacement and that the reason it got to be bad is because we failed to maintain / clean the fuel injectors so those need to be washed / cleaned / serviced too so that the whole issue is resolved. No mention about the "stabilitrack" thing at all. Due to our needs of the vehicle and our lack of cars knowledge we agreed to it without looking into it further.. Lights have been off since that and we didn't think much of it.
But then this weekend we got this "recall" letter in the mail for that very same vehicle... talking about the "check engine light" being the issue and an apparent leak of gasoline (via odor or visual leak)... Maybe these are totally unrelated ...
I checked the manual for the recommended maintenance and nowhere there is mention of regular maintenance needed for the fuel injectors.. I looked online and while there seems to be varied opinions most of them agree that is something not needed; neither it is the EGR valve replacement... so now I am really wondering! Was it all for nothing? And how is one supposed to know this. Is the "check engine" light enough of an issue to maybe think this was the right thing to do?
View 13 Replies
I have a 2008 Chevy Equinox, and recently I noticed a gas smell...I saw Chevy had a special policy to replace the fuel pump module, so I took it to the dealership hoping that would be the problem. Fortunately it was, and they replaced it for free. I got my car back Thursday afternoon, drove it Friday, and it sat yesterday without being driven. This morning I drove to the grocery store, and on the way home my check engine light came on. I have an ODBII scanner, so I plugged it in and got this code:
P0455: Evaporative Emission System Leak Detected (gross leak/no flow)
So I was wondering: (1) what is the cause and/or solution to this problem, and (2) is it possible the dealership caused this problem when they replaced my fuel pump module?
It seems awfully coincidental not to be related to the repair, since it is a fuel system problem, but I don't know enough about cars to be sure...
View 6 Replies
Chk engine light is on. Checked it at Advance Auto and indicated either cat or the O2 sensor (rear). So, I went to replace the O2 sensor and learned the hard way that you can't just unscrew the nut. I torqued off the stud to which the O2 sensor attaches. Muffler shop told me you need to heat up the stud/nut first to remove it. Oh well, lesson learned. So, I'm looking at replacing the pipe with the catalytic converter attached since I can't seem to fix the broken stud (or actually get the one I didn't break off). The problem is, my car is apparently a CA model and has the special cat on it. I live in VA. What sort of problems might I run into if I replaced the cat with a non-CA version? They are significantly less expensive. This is for a 2003 Toyota Siienna
View 1 Replies
