Engine cranks but will not start, it kicks back after cranking over for a couple of times i have replaced the crank sensor it has done this once before it kicked back hard enough to knock a tooth off of the flywheel after replacing flywheel and starter it started fine for three months then it kicked back hard enough to break a starter mounting bolt. i replaced bolt had starter checked and replaced again?
View 6 RepliesI have a 98 F150, 4.6L with approx. 245,000 miles on it. recently it started, then studdered a little bit and died. I managed to get it re-started, it then shuddered a little more although I was able to drive it back up the drive way and park it. Now, it will crank however it does not even attempt to fire. The sound that it makes when trying to start seems odd to me. Like the engine is just turning against a constant resistance instead of the normal starting sound. I tried shooting a little starter fluid into the throttle body and nothing changed. I pressed on the shrader valve and got a spew of fuel to come out so it seems that it might not be a fuel problem though it sure sounds like one. Just curious, what are the symptoms of a truck with no compression?
View 4 RepliesI'm a relatively new F150 owner (just got rid of the 98 Ranger I drove since 99), so I thought I'd check in to see if I was overlooking something obvious. A few days ago, after driving to the store with no obvious issues, I went shopping (coincidentally for oil change materials) and when I returned to my truck it would not start.
Here is a bit of info:
Starter cranks over the engine.
Battery is relatively new, and has plenty of power.
I can hear the fuel pump kick on briefly.
Check engine light is on (EGR Valve fault).
Engine started with starter fluid.
Engine ran like normal after starting.
Finally, the vehicle started/ran fine for a few days before the issue occurred again.
Like I said, I'm not too familiar with the vehicle yet, but I'm assuming the issue must be with the fuel delivery system. I plan on replacing the EGR valve, but I am curious whether a faulty EGR valve cause a no start? Also, I'm wondering if it's more likely that the fuel pump is going bad, or something electrical is the problem since I'm under the impression that the engine stops sending fuel to the cylinder if/when the engine doesn't start quickly after turning the key.
1994 Caprice Classic (350 cid LT1)... Engine cranks very slowly, almost doesn't start, sometimes starter disengages/re-engages. 1year ago mechanic checked batty, alternator and starter, all ok. I had starter replaced as it seemed the most likely cause. Eventually got better but now is worse again. Also notice a lot of movement on the dash voltmeter needle, sometimes high, sometimes low, turn signal moves the needle. Ive spent hundreds of dollars on troubleshooting and the new starter. What could be causing this?
View 4 RepliesI have a 1998 Chevy K2500 with a 350 engine. 220,000 miles. It starts fine when cold and drives fine. My problem is when I shut the engine off say to get gas or run into a store. When I return to start the truck it will just crank over as if it is not getting gas. If I pump the gas pedal it will fire up after a bit. It will start to stall if I put it into drive but will recover if I continue to pump the throttle. Once I am under way it drives fine until I make another stop. The check engine light is not on.
View 6 RepliesI have a 1998 chevy blazer and I cant get it to start. I removed the starter and turned the key and can see the starter popping out and spinning, but when I put it back into the flywheel all I get is clicking noise(like if the battery is dead) I had it on jumper cables so I don't think its the battery?
View 12 RepliesI have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 RepliesMt truck will suddenly die while going down the road. I know it has a oil sensor and wont start or run with oil is low,but recently it just dies in the middle of the road or won't start after a drive of a few miles. After sitting for a few minutes it will usually start. This was happening a couple of times a day until this week when we have had ice and snow, we have been in four wheel drive for four days and it hasn't died or failed to start even once. Whats up with that ?
View 3 RepliesI have a 98 ford Explorer that has some serious trans problems. It all started a while back when I was pulling a small 10 foot trailer and when I go to where I was going the trans puked out what looked like all of its internal fluids. It was a hot day, and these problems seem to be exacerbated by the heat but who knows. Yes the check engine light is on. I also have the occasional O/D OFF light blinking at me. As of late the vehicle has started to act like it has a stall converter on it. I have to rev to nearly 3k RPM before it will engage.
I changed the fluid and filter about 2 months ago and the fluid is already grey and nasty. The vehicle has also started going FORWARD in ALL gears, Reverse, Neutral, etc. all are forward gears now. The trans occasionally overheats and pukes out a large amount of fluid but I cannot tell where it is coming from. At road speed (55 MPH) the engine surges when it is at a constant 2500 RPM. I know my outlook is grim but if I just need a new torque converter I would like to know before I go the the Salvage yard for a different transmission. BTW. The engine WAS replaced around 12,000 miles ago with a donor engine from a flipped vehicle.
I've been fighting several problems with this car (1998 1.8t aeb 5 speed manual) I replaced the icm and coil packs just recently to fix an ignition problem. At least i thought the problem was fixed. Car was running good but still had an occasional loss of power and bucking.
Today I installed a new fuel filter and went for a drive to see if that fixed the problem. I get about a mile from my house and the car died at a stop sign. I tried several times to start it back up and nothing. I pushed it off to the side and left it there for the night, I'll go back in the morning to try to trouble shoot it.
Symptoms: I noticed that when I turned the key to the on position, the fuel pump relay would click and doesn't stop unless i turn the ignition off. The throttle body is also actuating at the same time, idle stabilizer? But its doing this with the engine off and key in on position. Also there is fuel pressure at the rail.
What would cause this? My only thought would be a failed ecu or possibly fuel pump relay (though I don't see how that would effect the throttle body).
I have a 1993 Chevy G20 van that was starting intermittently and now won't start at all. It cranks but doesn't start. On one of the occasions that I actually got it started I went to have the battery and alternator tested and was told that the alternator was good but the battery was low.
I then bought a battery charger and attempted to charge it. It has not started since. It also will not jump. I have tried to listen for the fuel pump and I don't hear anything...of course that could be because I don't know what to listen for.
So my question is: what more should I check before I give up and get it towed? I just want to be sure that I'm not spending all that money for a tow when it was something easy like a relay or a battery issue. I have some mechanical knowledge but no where to apply it (i.e.: my vehicle is outdoors and I don't have a lot of tools or a decent jack).
I've got a 1998 Jeep Cherokee Sport 4x4, 4.0 L I6, automatic, 169k miles, that often cranks but doesn't start up. When I cut the power and try again, it starts up right away. I'm concerned this workaround will one day not work and I'll be left stranded, so I'd like to fix this if it's cheap and easy. The symptoms suggest either a lack of fuel or lack of spark due to an electrical problem, so I replaced the ASD (auto shutdown) and Fuel Pump relays, but they made no difference. The other two relays - Starter and Cooling Fan - seemed irrelevant. What this could be? Maybe the crank angle sensor? (I'm not even sure where that's located.)
View 4 RepliesI have a 1983 Chevrolet C10 Silverado that I am slowly restoring. I recently had to change nylon timing gear and chain. It ran ok but now will only crank but not start. I am getting gas to the carb and I tried a couple of shots of starting fluid. It didn't try to start at all. I pulled some of the plug wires and I am getting spark. The plug wires look good. I am starting to get a little stumped.
View 19 RepliesI have a 2002 trailblazer that will start fine in the morning and after it sits for an hour or two, but once i start it and run it for over ten minutes and i shut it off when i try to re-start it, it will crank but won't start. the dealer cleaned the throttle body and injectors, check the fuel pump for presure and it was fine,and they got no error codes?????? I've read that in can be the ignition switch??
View 14 RepliesMy 2002 Tahoe cranks over fine (new battery), but, will not start. I have checked the fuel pump relay and have control power to energize the relay, but. no switched power from ECM to change relay state. Jumped rely 30/87 and pump runs. No DTC's. Gauge on instrument panel reads no fuel. Scanner shows 56% level. Tried to use my Snapon MT2500 to switch relay state and received error message "generic device control limit exceeded" ECM?
View 3 RepliesA friend is stumped by a problem with his truck, so I thought I might get some insight here. I haven't actually seen the truck, all that follows is from what he described, I'm just the messenger here.
The truck had been running fine on a used engine installed about six months ago. Then he ran it out of gas, it hasn't run properly since. It cranks fine, but won't start. He says it WILL start when spraying starter fluid into the throttle body, but only while the starting fluid is supplied. He also says he disconnected the fuel line somewhere near the engine, cranked the engine, and got good fuel supply (but no fuel pressure gauge reading). He's done some logical things: new fuel pump, fuel filter, spark plugs and wires. No luck. Figuring that he'd sucked something ugly into the injectors, he decided to replace those with no change (yes, I cautioned him about throwing expensive parts at it with no clear reason).
He reasons that he must be getting spark based on the engine running with starter fluid, and there must be fuel based on his test with the open fuel line, so he thinks it's an electronic problem, presumably the signal to the injectors. This is out of my league...and my friend is a carpenter, not a mechanic. If he could get a scanner would this kind of problem register a code?
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
I have a 2001 chevy Astro 2 wd. After rebuilding the motor it cranks has a spark and is getting fuel but won't start. Has a new starter new battery new coil crankshaft position sensor new distributor, cap and rotor plugs and wires but does not start...
View 3 RepliesI just replaced the auto transmission in my 1988 accord and upon first restart the car will not idle. I has been sitting for about 6 months while I replaced the trans, but was a daily driver prior to that. The car initially starts fine when cold, but shortly after startup starts running very rich and dies. Restart after this requires the throttle pedal to be held down. Engine will start after some cranking - but will not run under 2500 RPM and is obviously very rich. I've rebuild carbs before so I'm thinking about picking up a rebuild kit - just wondering if there could be other parts of the fuel control system that might be at fault.
View 2 RepliesMy 4.2L died all of a sudden, it cranks but won't start. Checked the harness side to coil packs, pos. signal but no neg. Tried a code reader keeps coming back link error. Does this mean PCM is fried?
View 4 RepliesA year ago my 1998 chevy camaro 6 cyl eng. randomly did not start. Then came back to it 15 min later and it started right up and did not give me another problem.3 months ago it did the same thing, but then would go a week at least with no more trouble sometimes longer sometimes more frequent.
within this past month it has become very frequent and I have had to push start it with the clutch a few times to get to work. It starts right up when I pop the clutch every time. Now the car will not start with the key no matter what.
Some more details on what it does now - When I first get in it after it has sat a little while you can hear the starter solenoid click the first three times or so when I turn the key. After that you do not hear the solenoid click anymore, but the relay up under the hood clicks every time with the key. (for kicks I even swapped the starter relay and the ignition relay with no change)
The battery is fairly new, but I load checked it anyway and it is perfect, plus I tried another good battery and jumper cables from a battery in a running car so that's not the problem. I have cleaned all corrosion off terminals and the ground to the engine and to the car.
I checked the resistance of the little piece on each of two ignition keys and they check fine.
I have checked the clutch switch down by the pedal multiple ways. checked resistance of the switch, voltage when the key is on and jumpering the plug with a paper clip.
when I push start the car and have it running I can turn the key with the clutch out nothing happens, but if I push the clutch in the starter will engage (grind) every time (I didnt do this a lot). this tells me that the clutch switch is working and the started is working right?
I did switch the starter out with another used unit and it did the same thing.
I unhooked the alternator on the off chance a short in that was drawing too much juice and not giving enough to the starter (I know I am really reaching here).