Chevrolet - 1500 :: Transmission Does Not Engage In Drive
Apr 11, 2011
Overhaul trans, new old pump, but doesn't engage in drive. Reverse and all three low work fine. Drive will only work when rpm's are applied. But without any power.
View 4 Replies
Apr 11, 2011
Advertisement
Volvo :: Transmission Began To Only Engage At About 1500 RPM?
I have a boat with Volvo AD41p engines and DP outdrives. The engines and drives have 830 hrs. Recently the transmission began to only engage at about 1,500 RPM. The Volvo dealer here says that I most likely need a new cone clutch, although they didn't really inspect it properly. Transmission fluid is full. ... show more.
I have been using the boat almost every weekend for 18 months, and it was running fine - the problem just started toward the end of a 1,000 mile trip - so the cables should be fine. It clicks into gear, but doesn't engage right away.
Chevrolet - 1500 :: Low Coolant - Antifreeze Smell After Significant Drive
My 2005 chevy silverado 1/2 ton seems to be low a quart of coolant every 2-3 months. First alerted to this during a oil change, check it monthly and need to add a little to the reservoir every other month. The temp gauge never goes over half way. I do smell antifreeze after I shut the truck down after a significant drive, but only if I walk to the front of the vehicle.
View 6 RepliesChevrolet - 1500 :: 1995 Silverado Diesel Won't Move When Put In Drive And Press Accelerator?
I have a 1995 Silverado Diesel 4X4 with 145K miles. I only drive about once a week to take trash to the dump. It's been running great until yesterday. I put in drive and went to pull out of my drive way and truck won't move. It makes a terrible sound in the rear of the truck but won't budge. I have checked transmission fluid level and appears to be good. I say appears because my drive way is on a steep incline and it's backed in, bed on the down side of hill.
View 5 RepliesChevrolet - Suburban :: 1994 - Won't Engage The Front Drive Shaft
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 RepliesFord Transmission :: 2002 F150 - Not Shifting Into Drive Unless Rev It Up To About 1500 RPM
I have a 02 f150 4x4 5.4 135 k the transmission will not shift into drive unless you rev it up to about 1500 rpm and when it shifts it goes in very hard but when you get moving it seems to work ok but every time you stop or slow way down it does the same thing. It works fine in reverse and the oil and filter is good. I am thinking TC but i dont know ...
View 3 RepliesLexus GX 2010+ :: Transmission Not Wanting To Engage After Being Put In Drive
We recently had an issue with our 2011 GX460. My wife first experienced the transmission not wanting to engage after being put in drive. Once it did engage there was a loud bang/pop noise, then no issues afterwards. The same thing happened to me this weekend. It was weird, like the brakes had frozen up then suddenly released and the transmission slammed into gear. We bought the vehicle used a couple months ago with 39k miles. With factory warranty remaining it will be heading to the dealer shortly.
View 14 RepliesChevrolet - 1500 :: 1992 - Transmission Suddenly Hit Limp Home Mode
I have a 1992 1500K extended cab 4WD with the 5.7L V8 engine (147,000 miles). It has been driving well since I bought it last winter. 2 days ago I took it on a longer road trip and it was doing great. Slowed down to take a 90 degree turn and the transmission suddenly hit "limp home" mode. It felt like it wasn't up-shifting out of 2nd , high RPMs while driving no more than 30mph on flat road. I have the proper amount of fluid and it is still red/pink and does not smell burnt.
Someone suggested that I check the transmission fuse but in looking through the fuse box I can't tell which is the tranny fuse. Also, I can only find one fuse box on my truck. Is there a 2nd?I feel like my next step is to take it to a transmission shop but I want to rule out whatever I can at home. I have zero experience with transmission work and don't want to get scammed into a rebuild if I don't need one. The transmission was working fine up until 2 days ago. No slipping, no hard shifting, and no noise...
S-10 :: 2003 4 Wheel Drive With Automatic Transmission - Front Axle Will Not Engage
Its a automatic transmission with a v6 4.3 vortec. The front axle will not engage, it is not the acuator (I replaced it and the cable) you can pull the cable and the axle will engage. There is a low buzzing noise(coming from the drivers side) until you give it gas. This noise stops when the front axle is engaged. The transfer case will go from hi to low without any problems.
View 1 RepliesLexus GX 2004-09 :: GX470 Transmission Intermittently Does Not Engage Into Drive For 6 Seconds
I have had an issue with my GX470 almost since I bought it in 2008. It will sometimes not engage in drive after backing out of a parking space.
It usually happens when it is warm and the car has been driving for awhile then I park for lunch or an errand. I come back start up the car put it into reverse backout of the car space and nothing for a good 5-6 seconds. Seems a lot longer when cars are waiting to take your space and honking.
Anyway I have been reporting it to Lexus at every service and getting a no trouble found. Over time it is occurring more regularly and it even happened at the dealership but of course I was the only one in my car at the time.
Ford Excursion :: Transmission Will Occasionally Hesitate To Engage Drive From Park
Just a little background, my Ex is a 2000 V10 4x4 with 217,000 miles. I've owned it for a little under a year. Very clean truck, and well maintained by previous owner. Now the issue. Starting about a month after I bought it, it would occasionally hesitate to engage drive from park. I checked fluid and it was full and clean. I had a buddy recommended that I check for chafed wires in the steering column which I did and found nothing. It seemed to get better for a while but now it's back. It's doing it more than half the time I put it in drive and sometimes takes 10-15 seconds to engage. So am I probably looking at a new trans? Or, is there anything that can be done to save the old trans?
View 1 RepliesTrans Sport :: 3T40 Automatic Transmission Suddenly Won't Engage Drive Or Reverse
This transmission shifted smooth and strong through all gears until today when it stopped all of a sudden to engage either Drive or Reverse. No previous signs of slippage, hesitation, stalling or lack of power whatsoever.
We checked the linkage to the transmission and it works as intended, nothing loose or broken, everything is in place. If there was something slightly different with it from other similar vans we have then it had a slightly delayed engagement in Drive (it took a second to engage it after you moved the lever) - on all other vans we have the transmission go into Drive almost instantly.
Van is a '92 Pontiac Trans Sport/Chevrolet Lumina APV with the 3.1L V6 Chevy TBI engine with the 3T40 automatic transaxle. Where we should start tackling this issue?
Ford Transmission :: 2005 F350 - 3 To 4 Seconds Delay When Trying To Engage Drive Or Reverse
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.
Ford Super Duty (1999-2016) :: Transmission Will Not Engage In Drive Or Reverse After Replacement
I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.
View 1 RepliesFord Super Duty (1999-2016) :: Transmission Shifted Into Drive Takes 5 Seconds Or More For It To Engage Hard
I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Transmission Work Slowly - Hesitates To Engage Drive After Reverse?
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
Chevrolet - Cavalier :: 2004 - Transmission Would Not Go In Reverse Or Drive
My future mother-in-law has a 2004 Chevy Cavalier. Last night night when she tried to put it in gear, the car would not go in reverse or drive. She recently had a tune-up on her car a month ago and everything seemed to be working fine. I think the transmission is dead. Does that sound right?
View 8 RepliesImpala - Chevrolet :: Transmission Slipping When Shifting From Reverse To Drive
2007 Chevy Impala3.5L 6-cyl Flex Fuel engine w/ 4 speed auto trans52,800 miles
Extreme driving conditions maintenance schedule kept.Transmission standard service done @ 32,800 miles which was 20k ago.
PROBLEM:
1) Twice in past three days, when shifting from reverse to drive the transmission has slipped, revving hard with rpms spiked above 3,000 for about 2 seconds before engaging the forward drive gear.
Normally I come to a complete stop of all reverse motion with foot fully on the brake pedal before shifting. Admittedly, I got sloppy the first time noted and still had very slight reverse motion when I shifted.
2) Several times late today, while driving uphill at approx 35 - 45 mph, when the car downshifted there was an extremely brief moment of transmission slippage with spiked rpms. It was so brief each time that at first I thought I'd imagined it until it happened again. Then it did it once on a level surface in a parking lot when having shifted from reverse to drive without problem and was gently accelerating the transmission again slipped for just the briefest moment when the normal automatic shift point was reached. So far, all incidences while driving have been so extremely brief that it was the merest hint of a hiccup.
3) When bringing the car to a complete stop, such as at a stoplight or when parking, as the transmission automatically shifts for the braking of speed, sometimes there is a minor but noticeable thunk sound seeming to come from underneath the car, I'd judge to be somewhere about under the level of the dashboard or slightly forward of that. Could that be from a worn or broken transmission mount? And, if so, could that be somehow causing the slippage problem?
4) This transmission has always, even since new, allowed more roll after being shifted into park, the engine shut off and my foot taken off the brake than any other car I have ever driven. If I forget to engage the parking brake quite tightly, the car will roll forward quite a few inches before the parking pawl holds it, even on the level. I've been told both by the dealership shop and the independent mechanic shop that there is no problem and that this particular engine/transmission combination tends to do this although my particular car seems to do so somewhat worse than average.
ACTIONS TAKEN SO FAR:
1) Have made an appointment to take the car into the mechanic.
2) Will check the transmission fluid level per instructions in the owner's manual tomorrow when I have daylight to see what the fluid level and color on the stick looks like.
NOTE:
1) I periodically check the transmission fluid level and it has never been low or discolored. The shop checked it for me, along with making sure everything else was road trip worthy, for an emergency 1,000 round trip in late November, just three months ago. No problems then.
2) No evidence on the garage floor of any leakage. Garage floor is dry.
QUESTIONS:
1) I presume the first step is for the mechanic to check the fluid level and examine for any leaks?
2) If the mechanic cannot duplicate the problem in a test drive, then what?
3) If the problem cannot be duplicated and no apparent cause found, I presume that the prudent course of action is to go ahead and have standard transmission maintenance done (i.e. drop the pan, check for debris, drain and replace with fresh fluid) then see if that halts the slippages?
4) Given that this car has already had failures of the power steering pump, water pump, and part of the wiring harness, and has a fuel pump starting to get noisy, despite aggressively maintaining all standard/preventive maintenance, that perhaps it is time to think of replacing this car, especially if there proves to be any truly major transmission problem found?
Cavalier - Chevrolet :: Automatic Transmission - Clunk When Shift From Park To Drive
I have had a 2000 Chevy Cavalier 2.2 liter 4 cyl Automatic for about 5 or 6 years now. I have noticed the whole time I have owned it that when I start the car and shift from Park to Drive I hear a clunk and the with the hood open the engine pivots back and forth one time more than it is supposed to. This only happens from park to drive, it does not do this from park to any other gears, and once the car is in drive everything is normal. The car has no shifting problems at all, no slips or clunking while driving or hitting the gas real fast on take off.
I changed the all three mounts on the car yesterday. Upper engine mount (still in decent shape), lower dogbone (tore to hell), and Transmission mount (decent). I really haven't noticed it get any worse over the years I just know its not right. I have never changed the fluid or the filter since I owned the car, and most likely it has never been changed in the cars life. Could a dirty filter, and dirty fluid cause this problem? Or could the linkage need adjusted or replaced?
Sierra :: 85 GMC 1500 2 Wheel Drive Truck Un-level?
1985 GMC Sierra 2 wheel drive. Truck sets lower on drivers side about 1 or 1.5 inches. Very noticable. Put new coil springs in front and 4 new shocks on. Back springs are original heavy duty with six leafs. Nothing noticable. don't know what to do. This truck is all factory original.
View 2 RepliesFord Transmission :: 2004 F450 - Transmission Will Not Engage In Any Gear
Just put the 6.0 back in the truck, engine working good now. Went to take it for a test drive and the transmission will not engage in any gear. I don't have any codes coming up on my scanner. Can not figure out why the transmission is not working from engine R&R.
- Fluid level is good
- Swapped wiring harness from my other truck and still nothing