Buick - Regal :: Number Of Teeth In Starter Gear That Engages In Flywheel Or Torque Converter
Jul 8, 2015
Pulled 3 starters at the junkyard to replace one that has a bad solenoid. Have a 2002 Buick Regal LS with 3800 series II engine. Found some on 3100 engines and one from a 3800. My starter has about 10 teeth on the gear that engages the flywheel. Some of the ones I pulled had smaller gears with only about 8 teeth.
Why the difference? Also one GM Delco starter was slightly longer (about 1/2 inch) than mine and had a small black hollow tube about 1 inch long at the rear of the starter and at the bottom. It fell off when I touched it. Looks like it might be a drain hole in case some water gets in to the starter. What is this really for?
View 1 Replies
Advertisement
In a matter of weeks, my truck destroyed two sets of flywheels and starters. When the ignition key engages, the engine "jumps back?. Apparently, this causes the starter and flywheel teeth to grind. My mechanic cannot determine the cause of the "jump back". He thought that it might be the timing. His examination and testing, however, proved the engine properly timed.
View 6 Replies
My 94 e4od does a few things. It doesn't seem to engage positively all the time. It doesn't grab well in manual 1st, but does in D. I had the FIPL reset at the dealership and he said he never saw a FIPL needing to be set so far one way. Also it has overheated a few times. Either the TC doesn't lock up correctly or its just not all the way in gear (if thats possible) I changed the fluid but it did it again recently.
Also the speedometer is jumping around like a nut case, the abs light is on...sometimes, when I have the headlights on and put my right turn signal on it feels like the TC locks up. Oh, yeah the lights are all jacked up in the back. The left turn signal light also has a small amount of voltage when I put the headlamps on (my test light lights up dimly) I thought it might be the multi function switch so I removed that and cleaned the connections. Nothing changed but I dont think that was it. I have troubleshoot this all day and I don't have too much of a clue to whats going on.
View 4 Replies
My torque converter is on the way out so I need to look for a new one. I'm pretty new at the transmission thing but I was told by my indy that my torque converter is on the way out. My problem is that I can't find the part number for my torque converter. I have a 2000 1.8t tip ATW.
View 3 Replies
The starter in my '93 Dakota was dying (usual signs of worn brushes) so I replaced it with a new one from AutoZone. The starters looked the same, and after calling back to double check the part #, the store swears it's the right part. However, when I engage the starter, it spins but the pinion gear doesn't engage the flywheel. I can't see how I could have installed it wrong - the two bolts seem to have only one place they can go.
View 19 Replies
2001 Buick Regal with approx 250,000 miles. 3.8L V6. Non supercharged It's my son's car. Used to be mine, I bought it with 19,000 on the clock.
The battery succumbed to the cold weather last Monday. On Tuesday, I put a new battery in, which itself now works fine. However, since then, the car refused to idle decently. It'll idle right after startup, but once you put it in gear, it'll die. When you start it, it seems to idle normally, you can let it warm up a bit and it'll settle down to about 900 rpm. BUT! Once you put it in gear, it'll stumble and die.
This problem started after battery replacement, so I have to wonder if it's somehow related to that. It ran fine before the battery died. I checked everything over thoroughly, and visually everything looks OK. No loose wires or hoses, etc.;
Today is the first time I've had to work on it since the new battery, so I thought I'd get it out there. I'm getting ready to go put a scan tool on it and will report back with those results.
View 4 Replies
I now have an annoying "clatter" sound coming from my supercharger cone housing ONLY when the car is in gear and at idle (i.e.,: stop light,etc.).. Had a new serpentine belt replaced 6 months ago with new water pump.114K miles, great condition otherwise.
View 1 Replies
When running up through the gears under normal acceleration I can feel almost a double shift in 5th gear. It doesn't occur using tow/haul so I assume it is the TC locking up. Everything else seems fine. Truck has 9k miles, mostly towing. 2016 6.2 ....
View 6 Replies
Ok so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 Replies
I have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 Replies
I have a 2004 Explorer 4.0L with 190,000 miles. My wife was driving it and the vehicle stopped moving. Sounds like the torque converter whining and will not drive in any gear or 4wd.
View 1 Replies
I just installed a new offset high torque gear reduction starter on my 2000 Excursion, and I noticed it starts much faster, but it sounds like the starter is knocking against something. Is this a straight swap out with the old style starter, or do I need to modify something?
View 14 Replies
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 Replies
I have a 2000 Ford F150 lariat with the 5.4 liter engine. At least once or twice a day, its like the starter hits a bad spot and will spin but not engage the flywheel. It has a new starter, battery, and solenoid. What this might be?
View 1 Replies
I just bought a 2000 f150 4x4 ex cab with the 5.4. Once in a while when starting, there is a grinding and the starter won't engage the flywheel. The truck has only had 17000 miles put on it in the past 4 years, and has sat quite a bit. Could the starter gear be gummed up and not engaging all the way, or should the starter be replaced? Or could poor contact on the cables cause this? Or is this a flywheel issue?
View 14 Replies
This issue has been happening for a few weeks now since it has been around -10C here. When I start the car it starts just fine but then the starter grinds against the flywheel (same as if you tried to start while car already on). I did a quick search and found that the relay may be faulty, Car is at 87000 kms.
View 5 Replies
I have a Chevy Tahoe 1999, Went to the store came out my Tahoe wouldn't start i had it towed home. My husband said the starter was clicking but wasn't getting enough power to turn the flywheel. We got a new starter put it on and it clicked just like it did when i tried to start it before. We took the new starter back and had the old one tested and it was ok so we put it back on and it still clicked like before. He said the flywheel was easy to turn, then he replaced the hot wire from the battery to the starter, now the starter don't even click.
View 17 Replies
I have a 1992 for explorer XLT 2-wheel drive Automatic 4.0 engine. The starter started grinding against the fly-wheel. Changed the starter and the same thing happened. There is no shim for this starter. I took it down and checked the flywheel--as much as I can see through the starter mount hole and the teeth on the flywheel are great. There is only the slightest point of impact where the starter is just grazing the flywheel.
I also grabbed the flywheel to look for looseness, thinking it might have broken and/or warped and I just can't see where it broken because of the small hole. It's solid! It's as if the whole thing just moved back about an inch and a half... I texted both the old and new starters with jumper cables, and the make certain, I took them to the local parts store and they also texted them. While both of the starter were fine, I'm not!
View 4 Replies
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 Replies
I have a 2001 Santa Fe 2.7l automatic. I recently changed out the automatic transmission (transaxle) as the old one had died. Now the starter motor plunger is not disengaging quick enough on start up and a screaming noise is made as flywheel turns as engine first turns over. I have just put a new starter motor in with exactly the same (screaming) result. The flywheel looks to be in reasonable condition as I inspected it when being put in, no teeth mangled and all teeth there. The transmission replacement was from a wrecked vehicle, I was told from same model vehicle but maybe a 2003 Santa Fe.
View 1 Replies
Four months when you tried to start the vehicle sometimes you will hear the starter. Drive in gauge but not meet the flywheel. Sometimes it would take three or four tries to turn over the engine. Yesterday went out to start the engine turn the key nothing happen no noise nothing but all the lights were working OK..
The repair shop said it was not the starter but flywheel missing teeth. But they said the main thing wrong is a need of new battery terminals. They change them in the truck started fine last night Today when my wife try to start it then come home saying thing happen nothing no sound, no nothing. Am I dealing with a bad starter solenoid perhaps or a combination of a bad flywheel??
View 1 Replies
