Bmw - 325 :: 2005 - Car Running Very Rough / Shaking Intermittently
Nov 23, 2011
I have a 2005 325xi BMW with 31,000 miles I get regular oil changes. Recently the engine seems to be running a little rough. The other day, after driving about 15 miles, the car started shaking and getting progressively worse. At first it seemed like the tires, but later it seemed like the engine. Also, when I accelerate, it seemed to get more rough, but again, not all the time. Last night, it was the worse yet. After I left the car for 2 hours, it didn't happen right away. Then it did again, but with 2 more miles to go til home, it stopped! Not sure if it's the fuel pump, fuel filter or even something with the wheels (sway bar?)?
View 10 Replies
Advertisement
I had a valve job on my 2006 Bmw 750 li, when I picked the car up from the shop the engine was loud ,before the job it was quiet couldn't tell the car was on , it also shakes back and forth while idling at every stop light,and when I take my foot off the gas the engine kind of jerks I have taking it back to the shop several times and they seem to not know what it could be they have recalibrated the valves and it seems to not shake soon after I leave but right when I'm a mile or so away it starts to shake again, what could be causing this? I'm pxxxed I paid them close to 4000 to replace the valves and now the car is running rough.
View 15 Replies
98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
View 10 Replies
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
View 3 Replies
I have a 93 Ford Explorer, manual transmission. About a month ago it intermittently started running very rough. I does this wether the weather is rainy or not. The engine has done this when it just started up, cold, and when it's been fully warmed up. I have been able to drive it, but it has been quite a challenge. When running, there is a very noticeable noxious exhaust smell. The check engine light has come on some of the time. When the eec codes were checked it only revealed 522, the car wasn't in park or neutral when running the test.
I have tried clearing and rerunning this test several times, yet 522 still shows up. No other fault codes. Don't know how this would cause engine to perform so bad. The fuel tank has been near full when it happened so I believe the gas to be good/ no water. The engine has a lot of mileage on it, over 200K, so I'm not sure if something inside could be malfunctioning, but don't know how to check. The car will run for days very smoothly before this happens again. I have changed plugs, wires and the pcv valve and it still occurs. It's like the engine is hitting on one cylinder when it happens.
View 14 Replies
My exhaust system was replaced on my 2005 Corolla in August. After driving it for just a few days, there was a shaking when the car idled. The mechanic replaced two engine mounts and the idle was much worse! He said it was ok to drive, so I started on my planned trip across the country. In Denver I took it to a mechanic at the Toyota dealer and they adjusted the throttle. It was better for a while, maybe a week and 1,000 miles. Now it is worse than ever! Having gotten two totally different causes from mechanics, I am not sure what to do next.
Also just before the exhaust sytem went, I had the 60,000 mile service done and had the car totally checked out by both Toyota, and an independent mechanic who specilizes in Japanese cars. After a car wash in California, the maintence required light came on.
What is going on?
View 8 Replies
Ok, so I have a 2004 F250, with 6.0L. when driving at a steady speed (doesn't matter what speed), the engine will run rough when coming to an idle, and stay running rough until I shut it off and let it sit for a bit.
After I cycle the key a few times it will fire up and run fine, so I came to the conclusion that air is getting in the fuel system. I then took the filter cap off that is located in the engine bay and cycled the key, which produced a lot of bubbles, which I am assuming shouldn't happen.
I guess my question is, should I have air bubbles in the filter bowl, when cycling the ignition?
View 1 Replies
I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
View 5 Replies
So my truck is intermittently running rough at idle for the most part and sometimes slightly loses a little power while driving down the roads. Seems to run worse as it warms up. When it runs rough it sounds like a cylinder is missing. The truck is throwing code P0269 for Cylinder 3 Contribution/Balance. Smoking isn't horrible coming out of exhaust but it's there and it comes out at a constant rate. The injector has been replaced by the previous owner recently. It has an egr delete, new turbo, ficm, ficm harness, HPOP, and stand pipes.
When I put the starter solenoid wire to the battery you can hear the engine skip. I did a compression test on cylinder 3, put oil in the cylinder and did the test again to find that I still didn't have compression. Assuming that this was an issue in the head I had my doubts that it was a bent valve and it could have been a bent pushrod.
Sure enough I found the intake pushrod for cylinder 3 was bent slightly so I replaced the pushrod. I started the truck again and seemed fine at first but just like before it started to run worse as it warmed up.
I was able to drive it to the gas station real quick to fill it up on fuel and drove back home which is a short drive, but the truck was running worse and worse and it eventually died on me. I attempted to start and had to jump start from my other truck and the 6.0 would not start. I ended up frying the starter trying to start it so I'm taking a break from it for now.... Ended up pushing the truck home.
The only thing I can figure is that I don't have oil pressure in the oil rail which is why it died but I don't understand why the truck still ran rough and pulled up with the same P0269 code....
View 14 Replies
Having a somewhat scary problem.....my truck is already a rough ride due to the fabtech lift and the 37's and you get a lot of feedback through the steering wheel. Its a rough ride down the highway but where it gets scary is at lower than highway speeds like 35-45 range. I can hit a bump and it will send the trucl into this insane cavitation that will literally shale the fillings out of your teeth. I cannot tell if it is in the drive wheels or the front wheels. The best way I can describe it is that its like trying to push a buggy in wal mart with a bad caster wheel on it. It feels like you are about to have a wheel fall off or that its broken off a tie rod or something. Then you simply slow down to a stop and you can drive right on like nothing was wrong. The vibration or shaking does not slow down with the speed. I cannot find anything obvious broken or damaged but this thing is getting dangerous to drive.
05 F350 DRW Fabtech 6 inch lift and 37's. 114k miles.
View 14 Replies
My 2005 yukon runs rough between 1300-1700 rpm, seems to run fine at all other rev's, doesn't matter what gear I'm in, (trying to troubleshoot put in low to see what it would do, same problem) if it's in the rough zone and I punch it it smooths out and runs fine, I've tried injector cleaner (Techron), premium gas, but it still does it....
View 2 Replies
So I have a 2005 Camry XLE, 3.0 l V6 with 160k miles. The car was running fine, but I decided to change the spark plugs today (overdue).
I went through the headache of removing the intake manifold, throttle body etc and everything seemed to go OK. I reassembled it all and now it won't idle properly.
It seems like a vacuum leak issue to me, but I have double checked the multiple hose connections. I did NOT disconnect the battery at any time.
I can Rev it up to 3 or 4000 rpm and it runs smoothly (all the cylinders seem to be firing) but it runs rough and dies without my foot on the accelerator. Also I noticed the exhaust manifold got cherry red like right now... after only a minute or two of running.
Are there any troubleshooting checks I can perform to narrow down the source of the vacuum leak?
View 13 Replies
We have a 2005 Prius with 77,400 miles on it. My wife came home from a short trip yesterday saying the engine was shaking the car and the CEL was flashing. About 4 months ago we also had the CEL come on but not flash and it ran a bit rough but not as bad as it is now. I was told by our local dealer that a flashing light is worse than if the light comes on and stays on. When this happened 4 months ago at 74,000 miles the dealer said they downloaded codes P300, 303, and 304 and that I needed to replace all 4 fuel injectors.
I realize that 300 is a general misfire code and 303 is a misfire code for cylinder 3 and 304 is for cylinder 4. After reading some advice on here 4 months ago, I cleaned my MAF sensor, ran some fuel injector cleaner through a tank of fuel, replaced all 4 spark plugs, and started buying Chevron gas. The CEL stayed off and our mileage went back to normal. I thought I had solved the problem but now this after 3000+ miles. I checked all the ingitors, connections, spark plugs, and wires yesterday and all seem to be in good condition. Maybe they were right and the fuel injectors are going bad. I am at a loss as what else to do other than take it back to the dealer now and plan do that this afternoon.
View 5 Replies
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 Replies
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 Replies
My 05 was running rough and misfiring quite frequently. After much deliberation, I took it in for a diagnostic hookup. The dealer said my driver side cat was clogged. Lucky for me, I was just under the warranty period(79673 miles). I have had it replaced and I can feel a noticeable difference in the way it runs. Could a clogged cat have made it run that poorly or am is it just in my head that it is running alot better?
View 7 Replies
I changed the timing chain, phasers, tensioners, guides, and cam sensors and solenoids about 30k miles ago. Truck now has 170k miles. This past weekend engine started running so rough, it had the whole front end shaking. Threw 8 codes..1 bank..lean, bank 2 rich, timing retarded, cylinder G and F misfire, and more codes. It seems to have jumped timing pretty bad.
View 1 Replies
My GX had developed yet another issue. To start off my car has an exhaust leak presumably at the head. Thats what i been told. This condition would throw a P0430 code ( catalyst system efficiency below ) once or twice a week, which id just erase with my plug in tool. Im not sure if the new developed issue is related to it, but now the engine is running rough especially noticeable between 1000-2300 rpm. Feels like misfire. When driving i can feel a drone or a frequent shake if rpms are in that range or when unloading the motor and rpms are dropping. No codes! Timing belt was changed at 90k miles car has 150k now. Not sure if its due for another one now and this can be the cause.
View 8 Replies
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 Replies
Our 2007 Avalon with 65xxx miles on it was skipping and running rough this morning. Running a scan with my VAG-COM gave me these codes.
Mode 07: Pending emission related fault codes Address 7E8: 2 Faults Found: P0305 - Cylinder 5: Misfire Detected P0355 - Ignition Control Circuit for Cylinder 5: Malfunction
Would you say it is time to replace the Coil for this cylinder, or should I do more troubleshooting first?
From what I've read on this forum, it appears cylinders 1, 3 & 5 are at the rear of the engine and are a PITA to change. Is there a good write-up or video on how to change these at the rear of the engine?
View 2 Replies
Code says P1121 Accelerator Pedal Position Sensor Range/Performance Problem. I heard that was wrong and its really coolant control valve? The battery drains fast and the can runs like crap. Would this code be doing that to the car?
View 18 Replies
