Audi - A6 :: 2004 - Check Engine Light Intermittently Flashing / Misfire On Cylinder 2 And 5
Dec 2, 2011
I have a 2004 Audi A6 wagon that has an intermittently flashing check engine light. I took it to the dealership to have the codes read and they told me that they got codes for Cylinder 2 and Cylinder 5 misfires. Additionally they got a code saying the Engine Coolant Temperature Sender was electronically faulty. What is this part and what does it do? Is it essential to fix it immediately?
The dealership recommended changing the spark plugs and the air filters for the cylinder misfire issue. We are also talking about replacing the timing belt since the car has 105k miles on it. I know there are several other parts that are replaced during the timing belt replacement (like the water pump, thermostat, oil seals, etc). Is it essential to replace these items if there is no immediate need to do so?
View 5 Replies
Advertisement
I have a 1999 Toyota Corolla. 4 cylinders.
I was on the road about 2 hours from home when my check engine light came on flashing. It stopped flashing so I kept driving. Three more hours of driving at highway speeds and it only came back on once. I then took it into autozone and the code reader told me I had a Cylinder 3 Misfire. The guy told me to change my spark plugs and I would be fine. It was time for a spark plug change anyhow so I drove home and did it. After I changed the spark plugs the car did not start at all. It would cough and sputter and try to start but not actually start. Changed the spark plug wires and then the car stopped even coughing and sputtering. It just didn't start.
I then noticed that my fuel line that feeds directly into the engine was rotten right next to the engine and if I pushed it in I could get the car to try to start. (Try and fail, but at least try.) The fuel line is a molded piece of rubber that flares at each end. It was one of the flares that was rotten and didn't seem to be sealing anymore. The hose is 7 mm inner diameter in the middle and about half an inch on the ends. I took some 3/8 in fuel line and used it to cover over one of the flares. The car tries to start now but wont. 3 of the four cylinders crank. I don't understand how I could break my car on such a simple repair job.
View 4 Replies
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
I have a 2004 Audi A6 wagon that's got 105k miles on it. A couple months ago, the check engine light came on while I was driving it. While it was on, it was flashing and the car felt like it was shuddering, like there was not enough gas getting to the engine. Then the CIL stopped flashing. It happened several times during my short outing that day, but then it never happened again. Now the flashing CIL is back and the car feels the same way when it's happening. I took it to an auto parts store to get the trouble codes read and the guy said P0300 (random cylinder misfire) and P0305 (cylinder 5 misfire) came up.
View 18 Replies
I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.
I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.
The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).
View 19 Replies
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
View 12 Replies
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
View 2 Replies
Driving the other night I ran drove over a pot hole going about forty pulled up to the stop light and my car starts to make funny noises, barley got the car moving again but managed to get home. I hooked my computer up to it and it says misfire at cylinder 2 and 4.
View 14 Replies
I'll try to break this down as best I can. I went to my mechanic this am with a check engine light. My suspicion is 02 sensors. This was confirmed as a problem area, but separate they said I had a spuratic misfire in cylinder 4. With that info, i pulled the plug to inspect (I had just installed new ngks in it and they have 18,000K on em.
I put beldon wires on about 8k ago.) plug looked to be normal, but there was definitely a puddle of oil from the valve cover leaking. Oil went into the cylinder head but I didn't really think that was an issue. Nothing abnormal jumped out at me so I reinstalled plug and checked all wire connections at both ends and called it a day.
Then I drove it. Check engine light flashing. Major performance stutters, etc. I drove it for about 20 miles and hoped it was just the oil raising hell in there and it would burn off eventually. It hasn't gone away yet. Maybe coil pack. Can the single portions of that pack be replaced, all i see them sell is the full three as a unit.
View 7 Replies
2000 Chevy S10 pickup
Had the check engine light come on, and when I checked on the code it gave a 4th cylinder misfire. Autozone instructed me to simply replace my spark plug with a new oem plug.
I replaced the spark plug as instructed. After about an hour of driving, the check engine light goes off and I think, great! Problem solved. However, another hour of driving and the check engine light is back on again, without going away.
I headed back to autozone to get a readout, just to find that it's the same code. So I put another spark plug in. Same result - check engine light goes off after an hour, only to come back on again permanently after another hour.
Now, normally I would think, this must be the spark plug line that needs replacement,however I am sure there must be some clue in the fact that the check engine light turned off for an hour.
By the way, not sure if relevant, but I also found a lot of build up around the spark plug before I initially changed it.In fact, there was so much that I had to scrape around the plug with an awl, and blow out the crud with a compressor,just to get my socket into place without there being crud in the way.
Any clue what that check engine off/on clue might be?
View 6 Replies
Got the flashing check engine light and loss of power for few seconds and then the light stayed still, from time to time it blinks for few secs, usually when I push the gas pedal little bit more but it stays still, flashed only twice in 2 days for seconds. I connected computer (not VAG) and it says "Cylinder 4 misfire". I have app scheduled with my mechanic this Thursday, but still need to commute to work. Is it safe to drive?
View 7 Replies
I plugged in a OBD2 reader and its show misfire on Cylinder 1.
I haven't driven the car for 4 days, and when i started the engine this morning, the engine show knocking when the regular engine kicks in (rough). i will be bringing the car in tomorrow (dealer). my car is a 2011 with 16k miles, strange for this to happen so early in age.
View 2 Replies
As the title says I have plugged a code reader in and it says "cyclinder three misfire". So I pulled the plugs and good god they were nasty. Some having a gap of 80-90 thousandths of an inch. So I figured the plugs were the source of the problem, thus I replaced them but to my dimise the check engine light is still on, and still reading the same ol' "cyclinder three misfire". I have put 350 miles on it in 24 hours of changing it to allow for proper time of the circuit cycling for the light to change but not sure if it takes longer...?
I also went ahead and checked the plug wires resistance when I had the plugs pulled and they ranged from 1.5-2.5k ohms shortest to longest (cylinder 4-1). And if your curious the magic cylinder three was around 2k ohms for however long that wire is, my guess would be 18 inches. Would this be out of tolerance, I know the norm is 10k ohm for every 12 inches or so...?
My next guess would be replacing the power pack or I guess you car guys call it the "ignition coil"...? I will say that the car does run much smoother after replacing the plugs.
View 5 Replies
Honda Odyssey 2005 – 176000 miles. Cylinder 4th Misfire – check engine lightHonda has about 176000 miles. When cold – before warming up – it acts like nothing is wrong – as it gets warmer – to the middle of the temperature gauge – it misfires.And runs rough. Evaluation: Honda Dealership thinks it is a cracked Valve or needs adjustment – they have replaced a spark plug and swapped coils. Not for sure.They think if that is not the case then there could be additional problems.Question: Why does it act normal when cold ? How can we confirm if it is the valve and not cracked head?
View 15 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong.
2001 7.3 Limited with 232k miles Bergen County NJ.
View 2 Replies
2004 Audi A6 2.7 T quattro ... Check engine light comes on and three mechanics all say i need new torque converter even tho i have no symptoms as yet. Will I get symptoms eventually, or could this be an electrical issue. When they turn off the warning light, it takes a day or so to come back on. There has been no reduction of mileage, no gear slipping, no problem accelerating.
View 2 Replies
I've got a problem with a 2000 Impreza 2.5RS 5spd. It started with the check engine light coming on. A trip to Auto zone revealed that the O2 sensor was the problem. But on the way home, the light came on again and started flashing. All the while the car started acting like it had a misfire. It idles really rough and the exhaust smells like it's running really rich. I've replaced the plugs and wires, and all corners of the ignition coil check out properly as well. Can the O2 sensor cause a misfire in one or more of the cylinders? Or is something else that I should be interrogating as the cause?
View 5 Replies
Bought a 07 GS450h w/ 82k on it last week thursday. car was serviced at 1 dealer it's entire life and battery was changed before I took delivery. After 100 miles of driving check engine light came on and i read 10 codes.
The codes are:
P0300 multi cylinder misfire (6 times)
P0301 cylinder 1 misfire (2 times)
P0303 cylinder 3 misfire (2 times)
Am I just looking at a simple spark plug change or is there something in particular I should look for? Is it worth the effort of bringing it to the dealer to repair?
View 14 Replies
I have a 2001 Mercury Grand Marquis. The check engine light came on and AutoZone diagnosed it as a misfire on Cyl. #4. I changed all the plugs but I do not know how to turn off the light to see if I fixed the problem. How to turn the light off.
View 3 Replies
Just bought 2007 Gs 350 in Dec 2015 with 60k miles. The other day I filled up with gas and drove to work. On the way home check engine light started blinking, check VSC appeared on display screen and traction light came on, car ran rough, and wouldn't accelerate. Got home and searched the net.. So I removed gas cap... No change.. Then removed neg battery cable for 10 min. Fixed problem for about 10 min. Then it all happened again. Next morning took it to Lexus dealer. The rep called and said it gave misfire cylinder 3. They said they checked valve springs and they are good, exchanged coil pack with different cylinder and still misfire #3. He said has to be injector so they want to replace injector ....
View 8 Replies
I have a 2003 Chrysler Town & Country and the check engine light is on. I brought the van to my mechanic and he told me there was a code that told him there was a misfire on cylinder #1. He started out with replacing the wire to cylinder #1, no change. He replaced the spark plug, no change. He installed a new fuel injector, no change. The van runs a little ruff at idle and when at a stop light.
View 9 Replies
