Audi - A4 :: 1997 - Rear Suspension Bushings Crunching Thumping Sounds When Body Torques Over Irregular Surfaces?
Apr 6, 2013
My rear bushings on my 1997, A4 Audi, make a crunching thumping sounds when the body torques over irregular surfaces. My Audi mechanic says that it is the bushings. Replacing the A frames and bushings will cost more than half the car's worth. I belief that dust got into the bushings when I went on dirt roads in Death Valley or they are just worn. When I blast the bushings with water the noise disappears or dampens for a while. Car has 186,000 miles.To keep the noise down, can I add graphite or some other material to the bushings?
View 4 Replies
Advertisement
I have a 2009 Corolla S. When I drive on the highway and the road dips and then comes back up, I hear a crunching sound as the wheels come back up. It almost sounds like springs. I thought maybe it was the cold weather but it isn't. The sound is in the front end.
At 53,000 miles, it seems early for this kind of problem and I never have had this so early in the life of a car. I do have the Toyota Extended Warranty of 125000 miles and 8 years. Would this be covered under that?
It doesn't really happen over bumps, it's when the car dips down and comes back up on the highway...50 mph or more.
View 3 Replies
When I go over bumps or rough surfaces I hear a rattle in the rear suspension. It sounds similar to the noise bad ball joints make. I recently had the car aligned and the shop said they couldn't find anything wrong. I'm going to take a look myself but was wondering if this might be a common problem. If maybe there are certain bushing that are known to wear out.
View 2 Replies
I have coilovers on my R32 with adjustable control arms and have been noticing a "thud" type of noise when going over uneven surfaces which appears to be coming from the rear.
I actually periodically noticed this noise when I first got the PSS's put on my car when going over larger bumps/dips in the road but lately it is becoming much more pronounced - occurring over uneven surfaces like parking ramps or driving over crappy roads. Over smooth surfaces, no problem.
Thought it was my rear sway bar bushings since they were making a really bad creaking noise, got those replaced and still noticing this damn noise.
View 1 Replies
Had crunching sounds from front passenger side. Replaced CVJ shaft and hub bearing/assembly noise gone but tire turns hard by hand drivers side turns freely. Looked on line and guy had same thing going on said maybe 4x4 vacuum actuator might be bad and truck stuck in four wheel .does this sound right? I have manual trans and gear box so I don't understand why the actuator is even there.
View 4 Replies
So I'm replacing all the control arms on the front end of my 02 F150 Supercrew 2WD.. Drivers side wasn't much trouble, other than having to cut the top mounting post of the shock off to get it out, and breaking the swaybar link. No big deal, I'll get new ones with new bushings. Was also planning on new shocks soon also, so it'll be sooner than later. Got the passenger side upper off, and new one in. No problem there either.
The lower rear bolt came out OK also... Had to cut this shock out also... No problem... Then I got to the lower front bolt. It is frozen solid to the bushing inner sleeve. Broke out the impact wrench, impact hammer, BFH, prybar, torch, cut-off wheel, sawzall, etc... Got the bolt cut off on the nut end, but can't get cut thru the other. The sleeve must be much harder than the bolt. Went thru a few blades. Need to either find the wrenches for my grinder, or buy some new ones. can't change the cut-off wheel out right now.
You can't get a hammer in there to get a good swing at it, and the bolt head is recessed up in the frame, so you can't even pry on it once you have it out a tiny bit. So, is there any magic potion to getting these bolts out? or am I doing pretty much everything everyone else has to do? Am I just lucky it's only one of the bolts? I know I've got thru this with leaf sprints also, but there easy to take off and take over to the workbench and get the drill, saw, etc at them better.
View 1 Replies
Waiting on a flatbed ... Everything was normal and then my abs light comes on then crunching sounds from my left front. Would a hub or wheel bearing cause this?
View 14 Replies
Need recommendation for replacement body mount bushing. Surprised to see the drivers side shredded. Poly replacement?
View 14 Replies
I have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
View 4 Replies
I already changed the two front struts but the clunk its still there when i hit a bump or irregular surface, the dealer told me that I have replace the two front strut mounts too (I have a 2007 Camry SE V6 w 112 miles on it), that can solve my problems?
View 4 Replies
My wifes 04 v6 touareg make noises now like either a computer crunching files or an electrical fire is about to happen?? the weird thing is when i turn off the display on the dash thru the menu it stops making the noise ?? its not loud enough to hear with the stereo on but it is when its off. the sound itself seems to be coming from the center of the display area over the steering wheel.
View 2 Replies
I just had the rear air compressor suspension replaced, but when it activates it sounds pretty noisy. It doesn't sound normal. What the heck is going on?
View 1 Replies
I have owned my 2011 CPO rx for a bit over two months now. It has 19 inch rims and Michelin tires. I find the suspension to be much harder than I would have expected on rough surfaces. For example, when I drive over even medium expansion joints the suspension is somewhat jarring. The fact that the suspension doesn't absorb more of the road surprises me. My wife drives a 2011 MDX and that is much better over similar roads. I always thought that Lexus had more of a reputation for a plusher ride. Could it be the shocks already? The car only has 33,000 miles.
View 11 Replies
I hear a thumping sound in the rear of my '97 Legacy wagon (Brighton model). The sound occurs when the car moves. Once the car has been running for several minutes the sound goes away. What is the cause and fix?
View 3 Replies
Just had control arms all replaced under warranty and it's still making chattering noises in the front suspension on broken rippled surfaces same as before ?? Front shocks were also replaced 6 months ago ...
View 14 Replies
Car has a little over 100K. How to replace the bushings on the suspension arms. Took my car in for the brake switch recall and was told my bushings were cracked. Not sure which ones, but I assume all of them. Looked online for a DIY, but not for the RX330. From some of the DIY's I've seen so far, it looks like a bit$! to replace those rubber bushings.
View 14 Replies
I have 2011 Elantra that I was driving down a slope yesterday and heard some weird noises. The slope had some holes.
While I was going down slowly, I heard my right front making noises. It sounded something like crunching or cracking noise coming from the suspension maybe? I also noticing this when I go over uneven bumps, I am here the same noise as well.
Is this normal? I got about 35K on my car now.
View 1 Replies
The front suspension on my 07 Accent SE has been crunching when I drive over rough patches in the road. The car is at just over 60,000 miles, and I don't drive aggressively. I'm planning on replacing the front struts, but I'm not sure which parts to swap out. I've purchased some Monroe struts, but do I need to replace the strut mounts as well? And are there any other parts I should change while I'm in there?
View 2 Replies
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 Replies
Was having some clunking sounds coming from the rear end on the old F150. Bro in law said it was lack of gear lube and the rear diff grinding from the start. Wasn't the issue. U - joints are shot and causing the issue. My question is I marked the drive shashshaft and flange with a sharpie but it rubbed off on the flange from free spinning the rear end seeing if the issue was there. From the drive shashshaft to the rear diff flange does the flange need to be marked or no? I did scribe with a nail the transfer case and marked the drive shaft with sharpie. So is the flange being marked important or just the bracket with the u-joint? Would've used soap stone but don't have any on hand.
View 5 Replies
On my 99 at the tip of the springs there is what looks used to be plastic wear spacers between the leafs. Mine are worn out and I think it is part of a squeak noise I am chasing.
What that part would be, where I could get them, and do I have to break down the leaf assembly to change them or could I raise the truck by the frame and take the load off the springs enough to get the in?
View 2 Replies
