1997 King Cab XE Pickup... Over the last couple of years, a noise comes from the dash of my pickup at speeds above about 30MPH, especially during acceleration. It is especially bad when I drop from 5th to 4th gear to pass someone (worse on a hill, extra load) but quiets some when going back to 5th gear (never completely goes away). What is making this noise??
View 6 Replieshave a 1997 nissan pickup 2.4 liter engine check engine light came on code say number 2 cylinder misfiring put in shop. they say that they can't get to misfire.truck run great.just that light keep coming on with code (p o 302)
View 11 Replies(code p.o.302) number 2 cylinder misfiring. 1997 nissian pickup 2.4 liter automatic. when I take truck out on highway check engine light come on with code p.0.302.when I get back to town. and cut truck off for maybe 20 minute. check engine light go off automatic I do not have to use a scan tool to erase. As long as I am in town light. say off. when I get back on highway check engine light come back on. have had 3 mechanic look at this they can't get it to misfire. they tell me the fuel and spark are doing what they support to do..do you think maybe computer bad. has 255,000 miles
View 5 RepliesMy AC blows cold for a little while, then it blows warm. If I wait and turn it back on the cycle repeats it self. I had the freon filled. Not sure what to do? 1997 nissan pickup....
View 3 Repliesmy mechanic is stump have a 1997 Nissan pickup 2.4 liter auto tranny. number 2 cylinder misfiring.my mechanic say it have fuel, spark. and he did a compression check say compression is good. code (p. o 302) keep coming on. he change spark plug and wire and distributor cap and rotor. but light keep coming on. he say the only other thing he can think may be is. to change the whole distributor he say the cam sensor is in the distributor. tuck have 264,000 mile on it.
View 5 Replies97 Nissan Pick Up, 5 speed manual, 192k. The specified oil is 75w90. When it was new, I drained to factory fill out and refilled it with Mobil one 75w90 synthetic and a bottle of Slick 50 for Manual Transmissions (I do not use Slick 50 in the motor). This has worked very well for me in past transmissions. Anyway, at around 160k, I would hear an occasional whine when at a steady 55 mph on level ground. If the road grade changed or I changed speed, it would go away.
At the 180k oil change, I decided to check the the transmission oil level. It was bone dry. The capacity is 2.1 qts and it took 2.1 qts to fill it. I filled it with Mobil One 75w90 again. I have checked it at each oil change and so far, it hasn't lost any oil since I filled it. I still have the whine at 55 mph on level ground and it still goes away with any pitch or speed change.
Now my question, would there be any benefit to switching to a synthetic 75w140 or a conventional 85w140? I'm thinking that the 75w140 wouldn't change anything but the 85w140 might.
1997 Nissan pickup 2.4 liter auto.gas gauge drop to all most empty when driving.then i can hit a bump in the road and it will go back to normal.
View 2 RepliesI drive a 2008 Nissan Frontier, bought new in Nov. 2007 with 53,000 miles on it. A few months ago, at about 50,000 miles, an annoying clattering noise started coming out of the dash. The noise was coming from the vent area of the passenger side dash and occurs when I start the vehicle or adjust the AC from Max to norm. I went online and found that the noise occurs in many of the full size Nissan SUVs, and is a failing Vent Actuator part. Doing further research, I learned, the part is fairly cheap, but buried in the dash and difficult to get to.
Of course that means that labor is very expensive to replace this part. Nobody seems to want to take the time to replace the part, except the dealer who wants $500 labor to do it. I have found dash diagrams and since it is cooling off lam thinking about taking on the project myself. With the vehicle having such low mileage, and little stress being put on the part, I feel that the part is of low quality and replacement should be covered on some kind of warranty. Nissan probably feels it is not a safety issue, but the noise is very annoying, and certainly lowers the value of my vehicle, that has otherwise been pampered and in like new condition.
I have a 91 Nissan pick up that is just making a clicking noise upon trying to start it. I replaced the battery. The inside light works, radio works, dash clock works, but still just clicking upon trying to start. Is there a clutch safety switch that could cause this, or starter, or ???
View 8 RepliesI drive a used 2012 Nissan Sentra that I purchased six months ago. Today is the first time I've ever had problems with it. I was driving down the road this afternoon and it started making a noise that's very hard to describe. It sounds like it's coming from the dash and is comparable to birds chirping or a computer-like/electronic noise. It kind of sounds like R2D2 hijacked my car! It also started making a scraping like sound from the back wheel. I thought I was dragging something under my car, but there was nothing there when I checked. When I started it again later, there was a squeak when I backed up that was either underneath or the rear right wheel side. The sounds only occur when the car is moving.
View 3 RepliesI have a 1996 Nissan Pickup that has been making a clanking noise (that's progressively gotten worse over time) in the steering column every time I go over a bump in the road. The sound is coming from the area between the steering wheel and the dashboard. It sounds like metal hitting metal. The steering seems to be functioning normally, other than the annoying noise. What's causing this?
View 2 RepliesI have an 97 Altima. When I hit on the brakes, it seems to be okay, but once I let the pedal go, there are clicking noise coming for the front wheels.
View 9 RepliesThe last couple days my truck (1997 f150 4.6l) has been having starting issues. At first it would just turn over and not start then the battery would die. So i bought a new battery and yesterday now its starts sometimes but when trying to start it while its ttuning over it stops then starts turning and starts up. Then i drive wherever I am going when i get back in to start there's nothing.
Its not turning over at all but when i turn the key there is a loud single knocking noise coming from behind the dash near the passenger floor vent. Actually there ate two noise from the same area, one when i initially trun the key and another when i release the key. But after just sitting there doing this it will finally turn over and start. What this is, there are no codes being thrown besides my dreaded P0401 which i cant seem to get rid of either. Ive changed every part that has to do with the egr system and cleaned the throttle body replaced vacuum lines and still the code.
I have a 95 nissan pickup V6 hardbody and speedometer goes in and out when it is out i just pound on dash and it will work. I took it apart and put white gauges on it and cleaned the connectors with electric spray. Put back together and it's still doing the same thing. But now when I hit dash it dosent work. Check engine light does come on if it don't work. But it did before till I pounded the dash then it went out.
View 1 RepliesCoolant temperature gauge bounce up and down.
View 6 RepliesWe have a Nissan Pickup that anytime (in every gear) that the truck reaches 2700 rpm it begins to jerk-feels like you're trying to start it in 3rd gear instead of first. We have had it in a shop with someone who just repairs Nissan's and have been unable to find the problem for over a year. Have looked at the catalytic converter, fuel pump, and air flow meter...nothing has worked...
View 2 RepliesI have a 95 nissan pickup V6. The speedometer stopped working today and engine light came on. truck sat there while I was working and went back out to it. Started truck back up and engine light was still on. As soon as I put it into gear the engine light went off and speedometer started working again. What it could be. It's a 2wd not 4wd
View 7 RepliesI have an 86 Nissan pickup with a z24 motor in it, yes the weird 4 cyl. With 8 plugs. It has been lurching when I let off the throttle or sometimes when I accelerate. Its been doing it for a year and won't do it all the time it is intermittent but does it more then it doesn't.
View 2 Replies1995 pickup truck 2.4 liter 4 cal 4WD. I have a new problem- I drove out to a favorite spot in the mountains (up a dusty road) and when I got to the end of the road my truck was suddenly idling REALLY rough. I was able to drive it home and it runs "OK" as long as you stay on the gas (I say OK but it does want to die and especially wants to die after it warms up and then harder to restart until it cools)- as soon as you let off the gas the idle is on the extreme side of rough. It did not act like a fuel filter has historically (hesitate when giving gas), but I had a filter so I replaced the fuel filter anyway.
I also pulled the air duct work and cleaned it all out, put a new air filter in and used CRC MAF sensor cleaner on the MAF sensor. I did pour in a Chevron fuel system cleaner but it would likely take a tank full at least to work and it does not run good enough to run a tank full through. I put in all new plugs (gapped) and checked resistance on the plug wires and cap- all seems to be acceptable. I checked all the vacuum lines and did replace a couple that were dry and crumbly. I am now at a loss,
I have a 2003 Nissan xterra se with 93,0000 mi. When i reach speeds greater than 60 mph it makes this rapid somewhat clicking noise. the dealer suggest to replace the belts. Of course that did not resolved the issue. then they claimed it was coming from the exhaust so they tinkered with it. it was gone for awhile but now it has return.
View 2 RepliesI work for for a non-profic organization. We have a 95 nissan 2.4L pickup, and one of the guys drove a fair distance while overheating because of a coolant leak. He did not quite make if back before the truck died. At first I offered to do the work on it thinking maybe it just needed a new head gasket and some machining on the head surface. But I did a compression test and 2 cylinders were around 30 and the other 2 around 40psi. Also there is coolant in the oil.
Given that the pressure is so low do you think there is much of a chance that the head is not completely warped and needs to be replaced. Is it unlikely that there would be damage to the bottom of the engine, cylinder walls, pistons or warped block? I know one cannot say for sure until the head is removed but I would like to avoid wasting the time because if the truck needs a new head or worse they are gonna just junk it.