Yaris/Scion & Vitz :: Misfire On Cylinder 3 - Car Hesitate In Reverse And Drive Only
Feb 17, 2013
Okay, the code I am getting is a "Misfire on Cylinder 3" code. The car hesitates in REVERSE and DRIVE only, not in neutral.
This is what I have already done: checked all wiring (fixed a bare wire), did an ignition coil swap (#3 to #2) to see if it was actually the coil (no change), replaced all the spark plugs (no change), replaced the MAF sensor (no change).
A shop I tok it to said it was the ignition coil, and that all the spark plugs needed to be replaced. They did not know that I already replaced all the plugs and, having already done the swap with another coil (and getting no change), I find it hard to believe anything they say.
I am leaning toward an O2 sensor issue or a fuel filter issue (but these cars are supposed to have lifetime fuel filters and that is not a job I ant to do if I don't have to).
I was also told that the "green thing" in this photo might be bad. What that is and/or why it would be bad. it does move a little, but so do all the others.
View 2 Replies
Advertisement
My friend has a 2003 Toyota Echo that is throwing a cylinder misfire code. Original code is P0302 and P0302PD. The car is idling rougher, kind of sounds like "put-put-put". Also, the car has no power at all. He lives on a hill and he can't even pull out of his driveway. Lastly, the smell of the exhaust is gassy.
We have changed out the spark plugs...no change. Next, we bought a new ignition coil for the number two cylinder...no change. So, maybe its the wiring. Put the new coil onto the number 3 cylinder and the number 3 coil onto the 2 cylinder. Low and behold, the misfire code changes to P0303 and P0303PD.
Thinking we might have gotten a dud of a coil, we bought another. Same thing...new coil on 2 code is P0302...new coil on 3, code is P0303. Could we just have gotten two bad coils? Oh, coils were a BWD brand coil and Duralast brand. Should we just go OEM from dealer? OR Denso from Advance Auto?
View 5 Replies
The check engine light keeps coming on and off on my 2001 Echo with the above code. The car runs fine and the check engine light randomly comes and goes. What would set off the check engine light, but not cause noticeable change in performance?
View 2 Replies
2005 Echo auto 120,000 km
I have intermittent misfiring (a few seconds every couple minutes) and get the codes 301 and sometimes 304/300. I cant drive out of my driveway without a sputter and when I turn into a parking spot or make a quick stop the problem is magnified. I initially suspected a wiring / coil issue but here are my results:
Shuffled coil packs. (1/2 & 3/4)
Shuffled fuel injectors.
Good compression.
Swapped ECM.
Inspected wiring harness.
Goof EFI / cutoff relays.
None of these led to any change in the codes (300, 301, 304)
Yesterday I swapped the fuel pump and it worked flawlessly for an hour of city driving (first time in two months) ... then the issue returned as before.
View 2 Replies
My car now has a little over 370,000 miles on her. The other day I noticed a hesitation while accelerating, like an instant loss of power/ jerk. It didn't do it much at first and the higher the RPM's the less it seemed to do this. Once I got the car up to 60/70 mph it was pretty much unnoticeable.
What it was. Thought maybe a vacuum leak. Nope. Maybe a bad TPS or CPS (didn't end up checking those), Thought maybe a bad injector or O2 sensor (didn't end up checking those either). I did try some fuel injector cleaner though but saw no change. I had a feeling it had to be a sensor or something because the motor itself runs great other than the intermittent misfire.
So I drive it in to work this morning. (1 hour drive each way) and aside from the minor hesitation/bucking/jerking while accelerating, everything went pretty smooth so long as I had the car up to highway speeds. So I get off from work and start driving home. The problem seemed to have disappeared completely for the first 3 or 4 miles, then all of a sudden it started up again. Only this time it had gotten much worse.
I could no longer get the car to go over 70mph and when I came to a stop the car sounded like it wanted to die (but never did). It took forever from a complete stop to get past all of the sputtering and hesitation/missing to get the car up to speed. It would keep cutting in and out (the motor bogging down, then gaining normal power for a second or two and so on and so forth). So I decide to take it to a shop to see if they can diagnose it.
The guy hooks up his code reader and looks at the car for a little bit out in the parking lot. All he could do was suggest to change the spark plugs and said that that was where he would start. So I went ahead and listened to what he said about the spark plugs (even though I knew there wasn't anything wrong with them because I had just changed them about a year ago). So I'm changing them out and when I take out cylinder 1's coilpack I notice it's wet. It seems somehow water or moisture had gotten down into there. So I dried everything off and changed the plug (the old one looked fine but I changed it anyway) and I went ahead and changed out all the rest of the plugs too (they all looked fine as well)
So after seeing the water around the #1 spark plug and coil pack, The injectors are right in front of there, so I decided to take the plug off the injector and take a look.
Sure enough, I took the plug off of the injector right in front of the #1 spark plug (far left spark plug) and wouldn't you know it, it had water down inside of it. I pulled the plug off of the injector next to it and it had water in it too (but not as much). How water could have gotten down in there but it did. I took a Q-tip and used it to dry up all the water down in there. Put everything back together and took it for a spin and everything was back to normal.
View 14 Replies
Mother in laws car had a bad misfire that goes away during idle. It seems to misfire during take off or slowing to a stop and Intermittently during cruise.
Came in with codes p0300 - random misfire and p0304 misfire cylinder 4
What I have done so far.
-Checked the oil
-Checked the plugs - they were bad so replaced them with ngk plugs
-part number - BKR5EGP
Misfire was showing in cylinder 4 on live data still
-Swapped coil 4 and 1
-Misfire moved to cylinder 1
-Swapped cylinder 1 with 3 to be extra sure and mis stayed on 1
-Swapped back to 4 and even 2 mis stayed in 1. Weird
-Pulled all plugs and checked compression getting 170psi
-Swapped plugs around in case 1 is faulty no luck
-Swapped number 1 and 2 injectors with no change.
So my thoughts now are leaning towards an ecm or a valve thing but would those not be on or off fails? It idles great and cruises great it's only bad we coming to and leaving stop.
View 1 Replies
I recently had detected always misfire on those cylinders. Any relation between them?
View 1 Replies
Driving on friday night, started to hear at idle the car rpms wavering. Drove home fine with no issues other than at idle. Then Sunday, drove the vehicle, and sometimes had issues when accelerating, seemed to misfire and lose power. Then when driving that day it died completely and wouldn't start. It turns, but no firing.
Got it towed to my place, ran the codes, showed 1300, 1305, 1310, and 1315. All to do with ignition coils. Did a quick spark check, and no spark at any cylinders. I figured it would be weird that all 4 would go at the same time, so i replaced the ECM instead. Still no spark. Where to go next? Also the car does have an immobilizer in it...that could be causing it to malfunction?
View 3 Replies
I have taken this problem to the dealer 3 times in the last 6 months and they claim not to notice any vibration or rattle. However, whenever I am at a stop sign or stop light with the car in Drive (automatic trans), a loud vibration sound can be heard and also felt in the steering column and the brake pedal. As soon as I press on the gas pedal again, the vibration goes away. The only other way to stop the noise is to place the car into Neutral. What might be causing this? Apparently, the noise is not audible outside of the vehicle since none of the techs at Toyota were able to hear a rattle or vibration.
View 14 Replies
info on changing the drive and power steering belts. I recently changed them on a 2003 Echo and took some pictures.
There are 2 belts on the Echo engine. A drive belt and a power steering belt. In order to remove the power steering belt you must, first, remove the main drive belt. If changing one it may be best to change both.
First remove right front wheel. Use jack stands to support the vehicle. Do not rely on a jack to hold it up. Next remove the passenger side front bumper cover. I feel it best to remove the cover as then you can do a test drive before enclosing everything. You can, if you wish, just lower cover to give access to the drive belts. With the cover removed, check the power steering pulley and make sure that you have access to the adjusting bolt. This bolt is accessed thru an opening in the pulley. See last picture.
Here are 2 pictures of the bumper cover installed and removed.
View 14 Replies
I have a 2010 Toyota Yaris four door. When I am stopped while in drive, the front left part of the vehicle rattles, sounds like it is around the front driver-side tire. If I change the car into Neutral, Reverse, or Park it will go away, but Drive or any of the lower gears will cause the rattle. I have only had the car for about 2 months and it has been doing this for a couple weeks.
View 5 Replies
I'm troubleshooting my sons 2000 Echo with a manual transmission. No reverse light. Very puzzling? The red wire with blue stripe in the trunk area is always hot. Makes no difference if the shifter is in reverse gear or not. Yet, the reverse lamps don't come on. I removed both bulbs and tested them at the battery using jumpers. They both come on. I have not gone under the car yet. My question is: does this car have a neutral start switch, and a back up light switch. If yes, which switch is feeding the other? Any pictures of where these switches are located? My guess is that the back up light switch is faulty, if there is one.
View 4 Replies
My car started popping out of reverse a little while ago and its started happening more often. I asked my mechanic uncle about it and he said its probably the synchronous. From my understanding, that means a rebuild of the tranny. I just got this car in Nov after writing off my Corolla in Oct. Is there anything else minor I could check?
View 3 Replies
The previous owner broke the key off in the ignition so I replace the ignition lock cylinder the problem is though even with the old one I can't turn the key to lock so it's stuck on acc. What I can try without replacing the entire column? Also it needs a catalytic converter, do I have to weld a universal one on ?
View 1 Replies
I have an automatic 2002 Echo. Like 2 or 3 days ago I started hearing a noise when I drive in reverse. Is a mix of friction and vibration and it gets louder the faster I drive, only in reverse. I read that this could be the symptom of a bad engine mount but I haven't been able to pinpoint it.
View 1 Replies
This happens many times especially when I am parking parallel and need to take reverse frequently. The steering kind of jams, then vibrates and then the car engine is off. I need to restart every time this happens. This is causing fear to drive the car on highways.
View 5 Replies
When ever my car is parked on a slope for 5 min I go to drive it and the car spudders when I accelerate.. when i leave it on flat ground after its perfect again.
View 5 Replies
My wife's 2003 Echo is sitting at 255 000 KM's (Canada) and has hardly had a days problem.However yesterday tried starting and completely dead-not battery as almost new. Ignition makes clicking noise-lights/radio etc all working.Called the BCAA ( Vancouver) the guy tapped with a pole on something in the engine and voila she started. He said something about the starter or starter solenoid-today again the car is dead. Will take it to the mechanic on Monday but how do I get it started meanwhile ? what did the BCAA guy do and what did he tap on ?
View 2 Replies
Was looking at some new side skirts for my 4d 2000 toyota echo but mine currently has the black plastic trim going completely around it. Are these easily removed? Like, are they clipped on?
View 3 Replies
I'm trying to remove the tail light units from my 2002 Toyota Yaris.
I've removed the central nut from the inside but the light unit won't budge. There are two other protuberances coming through the metal body work which are a plastic spigot, lower left of the metal bolt, and rubber type insert further away to the upper right.
I'm also presuming that there is some stiction with the gasket.
Even with the nut removed the outside of the unit has zero movement while the inside has a slight amount of flex.
Am I missing something?
View 4 Replies
know the torque value for a 2009 yaris oil pan bolts? In another forum somebody quoted a value of 6.6 foot pounds, that seems too small and the wrong value to me.
View 3 Replies
