Yaris/Scion & Vitz :: High Idle / ECT Was Out Of Range
Dec 21, 2010
I got a 2001 Toyota Echo 1.5L that was running rough on cold start ups. Got a trouble code saying the ECT was out of range, replaced that and after firing it up it started to hunt and had a very high idle, I unplugged the Idle air control and it still continued to hunt. I smoke tested it for vacuum leaks and no leaks. After plugging and unplugging things to see what made it disappear it now stopped hunting but maintains a idle of around 2000rpm in park or neutral, in drive or reverse the idle lowers to about 900rpm.
View 5 Replies
Advertisement
I have a 2003 Toyota Echo 1.5. About a year ago the cel went off and on intermittently and I got a p0511 code. For the past few months, the light has stayed on steadily except for a 2 week period when it stayed off. When the cel is on , the car idles slightly low for about a second just after start up. When the engine is warm, it idles steadily about 400 rpm above normal idle. When the cel is not on, the idle is perfect both at start up and when the engine is warm. I did take off the IAC and cleaned it, but it already looked spotless inside and seemed to operate smoothly.
View 2 Replies
I've always find solution to solve my little issues with my Toyota Echo 2004 Hatchback. Since last summer, my car seems to have a lot of problems to idle well with the fine rpm. Here are all the events :
-it all started last summer, when the motor would start to idle really high for a couple of minutes, before getting back to normal. When this happened, a p011 check engine would light up. I switched to synthetic oil, and it greatly reduce the number of time this happen, but it didn't solve it entirely. It usually happens when the motor is warm, but still not hot.
-Only once, during a long ride, I got a check engine. When I left the highway, my motor wouldn't stop idling high. stop/start the motor wouldn't change anything. I checked the check engine codes, if I remember well : p011, p016 and misfire. With a friend, we checked the crankshaft sensor, and it was really dirty, so we washed it, and it solved the problem! A few days after, I also change my spark plug because they were starting to be old.
-A few weeks ago, I started my car and it was idling high as usual to heat up faster (it is winter now). But then, the rpm suddenly drop really quickly. The rpm was really low for may be 2 seconds, and it nearly chokes, but just before it went up back to normal. Then low/high/low/high until the motor was hot. No check engine. I disconnected the battery for a few minutes, and when I reconnected it, the problem was solve. I also checked the air filter, but it wasn't dirty.
-Then, sometimes when I start my car, idling is fine but suddenly at a red light the motor start to run really low with a lot of vibrations and a bad smell. Stop and restart the motor solve the problem! But only until the next red light, or until the motor is warm enough. Still no check engine.
View 4 Replies
2008 Yaris high pitch noise when I used heater this morning.
View 1 Replies
What normal idle rpm is with a/c on with automatic transmission. Mine fluctuates between 680 to 710 with condenser fan on low and 900 when high speed condenser fan is on.
View 1 Replies
Mother in laws car had a bad misfire that goes away during idle. It seems to misfire during take off or slowing to a stop and Intermittently during cruise.
Came in with codes p0300 - random misfire and p0304 misfire cylinder 4
What I have done so far.
-Checked the oil
-Checked the plugs - they were bad so replaced them with ngk plugs
-part number - BKR5EGP
Misfire was showing in cylinder 4 on live data still
-Swapped coil 4 and 1
-Misfire moved to cylinder 1
-Swapped cylinder 1 with 3 to be extra sure and mis stayed on 1
-Swapped back to 4 and even 2 mis stayed in 1. Weird
-Pulled all plugs and checked compression getting 170psi
-Swapped plugs around in case 1 is faulty no luck
-Swapped number 1 and 2 injectors with no change.
So my thoughts now are leaning towards an ecm or a valve thing but would those not be on or off fails? It idles great and cruises great it's only bad we coming to and leaving stop.
View 1 Replies
I have taken this problem to the dealer 3 times in the last 6 months and they claim not to notice any vibration or rattle. However, whenever I am at a stop sign or stop light with the car in Drive (automatic trans), a loud vibration sound can be heard and also felt in the steering column and the brake pedal. As soon as I press on the gas pedal again, the vibration goes away. The only other way to stop the noise is to place the car into Neutral. What might be causing this? Apparently, the noise is not audible outside of the vehicle since none of the techs at Toyota were able to hear a rattle or vibration.
View 14 Replies
My Echo died on me this morning and would not restart. I was at a light at the time. I pushed it aside, waited a bit and it restarted. I made it to work and it died again after several hiccups along the way. It then died in my parking spot but would restart. It has 192k miles on it.
It was acting weird earlier this week in that it would lose power (not electricity) while moving and then continue on. It seemed to work if I gave it more throttle. I feel like its fuel related but I don't have a lot of spare money to guess at the problem unsuccessfully.
View 14 Replies
I have a toyota yaris d4d (2002). My engine light comes on, I lose power on throttle but engine will still idle. I turn engine off for a few minutes, then restart, I then carry on driving as normal as if nothing has happened. This happens every 2 weeks. Error code is p1121(accelerator pedal position sensor range/performance problem). How to rectify it ...
View 1 Replies
I have a 2010 Toyota Yaris four door. When I am stopped while in drive, the front left part of the vehicle rattles, sounds like it is around the front driver-side tire. If I change the car into Neutral, Reverse, or Park it will go away, but Drive or any of the lower gears will cause the rattle. I have only had the car for about 2 months and it has been doing this for a couple weeks.
View 5 Replies
I am buying a Toyota Echo that the engine shakes on Idle and the shaking increase a bit when the AC is On ....
View 2 Replies
My 2000 Echo (auto) developed a rough idle especially while in gear and with the AC running. It's a pretty rough vibration that seems to come from the left side (belt side) of the motor. When at a stop light with the AC off it is less pronounced.
Last year I had the belts and motor mounts replaced. Well let me rephrase.. I paid to have them replaced, not sure if they actually were. But the car ran great all year until the other day. The belts might be due for a replacement. They sometimes squeal in the morning as I accelerate from a stopped position while running the defrost. Also there is no CEL.
View 4 Replies
I have a Toyota Yaris '07 ... The car has been running pretty rough and ready over the last few weeks... During idle, it started rattling & shaking pretty hard... this progressed with the add-on feature of changing revs during an otherwise steady drive..... It chose the (in)opportune time of driving with our 3-year-old son, grumpy at that time, down heavily trafficked busy roadways during the holidays and stalled 3 x times.... It is in the garage/service center for the 2nd time ... They are stumped. They've checked air, fuel mix, filters, injectors, spark plugs, etc., basics. Computer diagnostics show nothing (briefly showed fault at Cylinder #4 but then that changed and now showing nothing). Toyota Technical is (apparently) stumped. They are talking about needing to order a new computer from Japan (minimum $1200 just for the part).
View 9 Replies
My 01 Echo coupe vibrates at idle and when running. I changed all mounts, with OEM ones,,,changed the bent cross-member, installed new rack and pinion, new bushings, terminal, bushings...and still the lil guy vibrates like a rattle snake tail.
I noticed that time chain is a bit slacked... what may be the culprit for that vibration, you can feel the vibs at gas pedal, dash and steering wheel.
View 9 Replies
I have a 2002 Toyota Echo. I just purchases a Creader V code scanner. My car is throwing a P0171 code. The light only comes on at idle or while going under 10 mph.
The data from the reader was:
Trouble Code: P0171
Fuel System sta B1 : CL, using HO2S
Calculated Load: 11.76%
Coolant Temp 188.59 degrees
The Freeze frame data was:
ST Fuel B1: -3.91%
LF Fuel B1: 36.7%
Engine speed: 795.5 RPM
Vehicle speed: 0 mph
Intake Air Temp: 82.4 degrees.
I went back today and ran live feed on the O2 sensors. I'm not sure what STF of O2S: STF means. That was another figure displayed on my code scanner.
The O2S S1 was reading between .04 and about .82. The graph looked pretty normal (I guess) in regards to going up and back down between 0 and 1. I don't know alot about mechanics, but I seen a youtube video of a graph showing it going up and down and what is normal. Mine did that on S1.
O2S S1: STF was: 3.89 and -1.57%
O2S: S2 was a different story. It was between like .58 and .66.
The O2S S2: STF didn't give me a value at all. It just said " --% ". The graph of this was slowly going up but in a small range. It started at like maybe .4 and would go up to say .5. The next wave would be like .45 to .55, then .50 to .60, then .58 to .66 etc. So it was not ranging just between 0 and 1. It had a very tight range that gradually increased upwards.
I built my own smoke machine before testing with the code scanner and I didn't get any smoke coming out of the car except for around the air filter housing where the lid meets the bottom portion. I don't know if it's because I had the air filter wrapped in plastic wrap. Can I have an air leak where the filter cartridge connects that would case a lean code P0171? Maybe I should go try to smoke test again. I did it about 3 weeks ago and I can't recall exactly where I had the smoke going into. I thought I disconnected the PVC hose from the brake booster and plugged it in there. I assume the smoke would get thru the whole system. It took about 2 min before the smoke came out of the filter housing.
The car only sets a lean code at idle or going less than 10mph and I'm coasting in a residential area.
I have an inspection coming up in May and need to get this thing fixed before that. I can't find any other air leak, but I wasn't sure a leak around the filter would cause this and I'm not sure the leak wasn't caused by the plastic wrap.
I'm thinking my only other prob could be fuel related. Fuel filter, fuel pump, clogged injector, or can my O2 sensor be bad and causing this? I've already replaced all spark plugs and coils as well as the PVC valve and cleaned the MAF sensor with the appropriate spray.
The car runs ok. The exhaust seems to smell RICH. Like Gas. I don't think my fuel economy is as good as it use to be. It has dropped from as hi as 42 mpg to between 38 and 40 if I'm lucky.
Back when I was having problems before and realized I had a bad coil, I had tried some injector cleaner. Why the codes were back then, but I had erased them and the car ran fine for about 2 months and the light came back.
My MAF sensor was .14 lbs when I was watching the live data above. I plugged my fuel pressure tester directly into the fuel line coming from the fuel tank and got a reading of between 42 and 44 lbs (car not running, just by trying to turn the engine over). I don't know if that is as accurate (or useful) as having the fuel pressure tester on the car and in line to allow the car to start up and run and watch the tester. I have to wait until my part comes do run the test that way.
View 14 Replies
I've been having trouble getting my 2001 toyotoa echo to start in the cold weather and STAY Idling. All I can do to keep the car going is hold my foot on the gas until it warms up, then it stays running, low idle, but running. It starts fine the rest of the day, but that first start in the morning doesn't take. The check engine light comes on and stays on, and the car seems to idle rough at stops.
At first the Mechanic I took it to (good guys) cleaned out my throttle body (physically and chemically) and this seemed to solve the problem for a couple weeks. I'm located in Toronto, Canada, and we're heading into cold weather and I just want a car that starts. It started up again recently and I'm now being told (on my second visit to the mechanic) that it's my throttle body/idle control and that this part needs to be replaced, to the tune of 627.00 + labour.
View 7 Replies
My friend has a 2003 Toyota Echo that is throwing a cylinder misfire code. Original code is P0302 and P0302PD. The car is idling rougher, kind of sounds like "put-put-put". Also, the car has no power at all. He lives on a hill and he can't even pull out of his driveway. Lastly, the smell of the exhaust is gassy.
We have changed out the spark plugs...no change. Next, we bought a new ignition coil for the number two cylinder...no change. So, maybe its the wiring. Put the new coil onto the number 3 cylinder and the number 3 coil onto the 2 cylinder. Low and behold, the misfire code changes to P0303 and P0303PD.
Thinking we might have gotten a dud of a coil, we bought another. Same thing...new coil on 2 code is P0302...new coil on 3, code is P0303. Could we just have gotten two bad coils? Oh, coils were a BWD brand coil and Duralast brand. Should we just go OEM from dealer? OR Denso from Advance Auto?
View 5 Replies
When ever my car is parked on a slope for 5 min I go to drive it and the car spudders when I accelerate.. when i leave it on flat ground after its perfect again.
View 5 Replies
My wife's 2003 Echo is sitting at 255 000 KM's (Canada) and has hardly had a days problem.However yesterday tried starting and completely dead-not battery as almost new. Ignition makes clicking noise-lights/radio etc all working.Called the BCAA ( Vancouver) the guy tapped with a pole on something in the engine and voila she started. He said something about the starter or starter solenoid-today again the car is dead. Will take it to the mechanic on Monday but how do I get it started meanwhile ? what did the BCAA guy do and what did he tap on ?
View 2 Replies
Was looking at some new side skirts for my 4d 2000 toyota echo but mine currently has the black plastic trim going completely around it. Are these easily removed? Like, are they clipped on?
View 3 Replies
I'm trying to remove the tail light units from my 2002 Toyota Yaris.
I've removed the central nut from the inside but the light unit won't budge. There are two other protuberances coming through the metal body work which are a plastic spigot, lower left of the metal bolt, and rubber type insert further away to the upper right.
I'm also presuming that there is some stiction with the gasket.
Even with the nut removed the outside of the unit has zero movement while the inside has a slight amount of flex.
Am I missing something?
View 4 Replies
