Yaris/Scion & Vitz :: Echo 2003 - Check Engine Light But No Code
Dec 29, 2013
Recently changed a front pipe manifold on my Echo 2003 4doors Five spd.
Noise I was reporting ealier thread seems to have subsided somehow but I did not hit the high road again, since the repair.
But I have this check engine light that went off 3 days ago and stays on.
Tried 4 times to read the code of OBd II reader and it pulls nothing. As if everything was normal.
I changed the batteries but it acts like it does regularly and it shows like there is no code to pull out.
Could that be a Ghostly Check Engine. It is still on at the moment meaning every time I drive the car.
View 5 Replies
Advertisement
First owner, 192000 miles. Check engine light came on during last winter, I put fuel injector cleaner with gas and it went away for a while. It came back on, if i reset, I can drive for about 50 miles before it comes back on line. Also, may be two or three times a week, when moving after a stop, the vehicle stalls, i have to take the feet of the gas pedal and give gas again.
I called up the dealer asking for fuel filter and fuel injector parts prices. Fuel filter is in the gas tank and not meant to be replaced. The fuel injector I was told 4 x $155 each. For diagnostics they need $100
See attached, I was able to clean sensor 1. I could not unscrew sensor 2, the screw is rusted, plus there is no room to get a longer screw driver and turn.
View 14 Replies
My great 2001 Echo is acting up for the first time in 11yrs!.. This weekend I decided to have my mechanic change the manual transmission fluid and do a general inspection of the vehicle. He found nothing wrong. I decided that before embarking on a long trip, that I would change the oil/filter, flush the radiator and put new antifreeze, change the airfilter, replace the alternator belt, added a small bottle of Lucas complete fuel system and a new battery.
I was proud of my DIY performance except that the next day the engine light came on! I took it to AutoZone where I purchase all the supplies and battery and they came up with CODE P1349 which I researched and found out about VVT(variable valve timing) malfunction. Some of the reasons for this malfunction are: low fuel pressure due to clogged or bad injectors..... Fuel pump regulator....camshaft malfunction or ECU (engine control unit) problem.
1.This morning the light was off then ten or fifteen minutes later it went on and at the same time the iddle got much faster for about two or three minutes, (in other words the engine was running faster even when I took my foot off the accelerator) and then came back to normal.
2. Later on the light was off again followed by the same sequence of events. Then at one point later I could tell that the the engine was running fast again for a couple of minutes.
View 14 Replies
My car is a standard and was working fine not indication of any troubles. Stopped and pumped $20 gas. Started to drive and car starts running rough especially at low speeds. Going up hill is brutal. Engine light flash when trying to accelerate, slow getting up to speed, shudders- not a lot of power, once up to speed engine light turn off.
Press the gas to go up hill- engine light comes back on and it begins all over, it also sounds like it is not running on all cylinders.
Is there any suggestions: fuel pump, fuel injection...spark plugs and wires? Something more serious
View 7 Replies
The other day my 2000 Echo started missing, she would run fine until after about 5 mins. After that, it would run like it was only running on two or 3 cylinders so I took her to Auto Zone for a code check--it came back with p1315,p0141 & p0304. On the way home it really got bad! She started dying on me. Just like u turned the key off. Before coming to a complete rest I turned the key all the way off and back on and she ran for 30 seconds or so - You would have to turn her all the way off--back 2 clicks--one click back would not work and this is the way I got her back home--about 7 miles turning her on and off. I wish now I had not hooked her up to there code checker because I think it burnt something out.
View 6 Replies
I have a 2007 Yaris, 180,000 miles, The check engine light comes on. With a P0011 code. I know that that could mean either:
blocked oil passage
Mechanical timing fault
Camshaft position a timing over advance
Failed OCV
Or VVT controller assembly fault
Since it's been really cold out I figured maybe it was a blocked oil passage, but after an oil change and quick check - I no longer think that's the problem.
The car runs great and it doesn't seem anything is wrong at all ...
View 3 Replies
My friend has a 2003 Toyota Echo that is throwing a cylinder misfire code. Original code is P0302 and P0302PD. The car is idling rougher, kind of sounds like "put-put-put". Also, the car has no power at all. He lives on a hill and he can't even pull out of his driveway. Lastly, the smell of the exhaust is gassy.
We have changed out the spark plugs...no change. Next, we bought a new ignition coil for the number two cylinder...no change. So, maybe its the wiring. Put the new coil onto the number 3 cylinder and the number 3 coil onto the 2 cylinder. Low and behold, the misfire code changes to P0303 and P0303PD.
Thinking we might have gotten a dud of a coil, we bought another. Same thing...new coil on 2 code is P0302...new coil on 3, code is P0303. Could we just have gotten two bad coils? Oh, coils were a BWD brand coil and Duralast brand. Should we just go OEM from dealer? OR Denso from Advance Auto?
View 5 Replies
I am buying a Toyota Echo that the engine shakes on Idle and the shaking increase a bit when the AC is On ....
View 2 Replies
I was driving home and I lost power in my engine. When I gave it gas you can hear it miss fire and loose power I got it home and it starts and idles but not smooth. What should I be looking into at this point? I'll check the coils and plugs now but I'm not sure after that. I heard about a bad ecu but it still runs so idk.
View 7 Replies
I just got my wife a 2000 Echo with 224,000kms on the odo. Everything appears to be fine other than a mystery rattling noise under light acceleration. If I were to describe it, it sounds as if a box of rocks were to be shaken around. Or like a rattling loose chain... <------ definitely hope it's not that!
From a search, it seems like others have encountered this strange noise but have not reach what the cause is.
From what I gather, the timing chains on these motors are literally never touched and should last the life of the vehicle.
View 1 Replies
My wife's 2003 Echo is sitting at 255 000 KM's (Canada) and has hardly had a days problem.However yesterday tried starting and completely dead-not battery as almost new. Ignition makes clicking noise-lights/radio etc all working.Called the BCAA ( Vancouver) the guy tapped with a pole on something in the engine and voila she started. He said something about the starter or starter solenoid-today again the car is dead. Will take it to the mechanic on Monday but how do I get it started meanwhile ? what did the BCAA guy do and what did he tap on ?
View 2 Replies
I have a 2002 Toyota Echo. I just purchases a Creader V code scanner. My car is throwing a P0171 code. The light only comes on at idle or while going under 10 mph.
The data from the reader was:
Trouble Code: P0171
Fuel System sta B1 : CL, using HO2S
Calculated Load: 11.76%
Coolant Temp 188.59 degrees
The Freeze frame data was:
ST Fuel B1: -3.91%
LF Fuel B1: 36.7%
Engine speed: 795.5 RPM
Vehicle speed: 0 mph
Intake Air Temp: 82.4 degrees.
I went back today and ran live feed on the O2 sensors. I'm not sure what STF of O2S: STF means. That was another figure displayed on my code scanner.
The O2S S1 was reading between .04 and about .82. The graph looked pretty normal (I guess) in regards to going up and back down between 0 and 1. I don't know alot about mechanics, but I seen a youtube video of a graph showing it going up and down and what is normal. Mine did that on S1.
O2S S1: STF was: 3.89 and -1.57%
O2S: S2 was a different story. It was between like .58 and .66.
The O2S S2: STF didn't give me a value at all. It just said " --% ". The graph of this was slowly going up but in a small range. It started at like maybe .4 and would go up to say .5. The next wave would be like .45 to .55, then .50 to .60, then .58 to .66 etc. So it was not ranging just between 0 and 1. It had a very tight range that gradually increased upwards.
I built my own smoke machine before testing with the code scanner and I didn't get any smoke coming out of the car except for around the air filter housing where the lid meets the bottom portion. I don't know if it's because I had the air filter wrapped in plastic wrap. Can I have an air leak where the filter cartridge connects that would case a lean code P0171? Maybe I should go try to smoke test again. I did it about 3 weeks ago and I can't recall exactly where I had the smoke going into. I thought I disconnected the PVC hose from the brake booster and plugged it in there. I assume the smoke would get thru the whole system. It took about 2 min before the smoke came out of the filter housing.
The car only sets a lean code at idle or going less than 10mph and I'm coasting in a residential area.
I have an inspection coming up in May and need to get this thing fixed before that. I can't find any other air leak, but I wasn't sure a leak around the filter would cause this and I'm not sure the leak wasn't caused by the plastic wrap.
I'm thinking my only other prob could be fuel related. Fuel filter, fuel pump, clogged injector, or can my O2 sensor be bad and causing this? I've already replaced all spark plugs and coils as well as the PVC valve and cleaned the MAF sensor with the appropriate spray.
The car runs ok. The exhaust seems to smell RICH. Like Gas. I don't think my fuel economy is as good as it use to be. It has dropped from as hi as 42 mpg to between 38 and 40 if I'm lucky.
Back when I was having problems before and realized I had a bad coil, I had tried some injector cleaner. Why the codes were back then, but I had erased them and the car ran fine for about 2 months and the light came back.
My MAF sensor was .14 lbs when I was watching the live data above. I plugged my fuel pressure tester directly into the fuel line coming from the fuel tank and got a reading of between 42 and 44 lbs (car not running, just by trying to turn the engine over). I don't know if that is as accurate (or useful) as having the fuel pressure tester on the car and in line to allow the car to start up and run and watch the tester. I have to wait until my part comes do run the test that way.
View 14 Replies
I'm getting error P0125 on my 2001 Echo, which points to possibly a faulty ECT sensor.
Where is this sensor located? Seems like under the air box? Is replacing this part as annoying as it looks? And, are there any other possible causes for code P0125?
In case it's related, I will mention that code P0171 (mixture too lean, I believe) is present as well, and the car does hesitate upon initial acceleration when standing still. Once it's moving, it works fine.
Maybe it's time to start thinking about replacing this car... it has 216,000 miles...
View 1 Replies
I have a 2003 automatic Echo, 200 000KM. I was on the highway with the A/C ON and i suddenly noticed it started blowing warm air(because it was a hot day). I was a bit on a rush so i decided to just roll down the windows and keep on. Once i was on a red light, i noticed i could hear a sound, coming from the straps(wich seemed logic to me since the A/C stopped) The sound was a kind of continuous screeching. It also smelled a liitle bit like burnt plastic or rubber. So i stopped the car, check under the hood, saw nothing, so I decided to start it again. After like 50m, it stopped by itself, and now i can't start it. I even tried to jump start it with a buddy's car and nothing changed! I still have some battery, everything works, but the starter wont even "click" when i engage it...
View 6 Replies
Echo 2003 2 door
Running lights: OK
Headlight mode, the running light stay illuminated but the head lights don't come on and the high beam light illuminates.
It feels like a relay but I don't know where to start. Had to drive home in the dark with the moon light my way home. I'd prefer to not do that again.
Found two 10A fuses under the hood. Both blown
The connectors to the lights are corroded and strangely, covered in oil. I could not find an oil leak (Problem with previous owner?)
View 3 Replies
My ac compressor just went out in my 03 Echo and now the car won't even start. I believe the pulley on the ac seized up b/c the belt won't turn and it just makes a horrible squealing noise when you try to turn the engine over. Right now I'm too broke to get a new ac compressor so I figured I'd just replace the belt with one that bypasses the ac altogether. Is this possible with the 03 Echo? And if so, any diagram or pic of the engine with and without the ac belt on it? I need my car back on the road asap...
View 5 Replies
My Echo is giving me problems. The red thermostat light has been coming off and on for the past two months. I had the radiator, fan and thermostat replaced. It started blinking again after two days. I took it to a mechanic that tested to see if it had a head gasket blown. That wasn't the problem. The mechanic said it was the water pump. I had the water pump replaced today and drove approximately 12 miles home when the red light started blinking again.
View 8 Replies
The check engine light has been going on and off for a couple of months. I took it in to be looked at and the mechanic said they couldn't get a code, couldn't get a "good read" on what was wrong. They said I could take the car back (but they couldn't give me an inspection sticker) and drive it for a couple of days and if the light comes on, take it back to them. If the light doesn't come on after a few days, they will give me the sticker. I can't believe my car is going to act any differently than it has for the last few months -- light comes on sometimes, sometimes it doesn't. Shouldn't the mechanic be able to tell what's wrong.
have a 2005 Scion with about 60,000 miles.
View 3 Replies
My 2003 echo has a noisy manual transmission. The former owner put a salvaged tranny in it. Reverse sounds terrible.The car has 373000kms on it. I'm going to change the transmission oil this week. Any recommendation as to oil type? Should I put in Lucas oil treatment.
View 1 Replies
My wife's 2003 Echo has had some persistent issues. We've replaced the right front wheel bearing 3 times now, and the driver side front once.
The current issue is steering wheel vibration. It's hardly noticeable at 40mph, but gets serious around 60mph.
Some things I noticed when I took it for a spin today:
The right front wheel makes a clunk-squeak sort of sound on rough road. It has a looser feel at those times. Sort of like an old truck. Not a peep out of the driver's side.
The steering wheel vibration is not changed by shifting to neutral (it's an automatic). The vibration increases with speed, and is rougher at 50mph coming down on a coast from 60 than it is accelerating up from 40.
The vibration is reduced with slight braking and stops with heavy braking. In turns where the weight of the car is shifted to the right side, the vibration is reduced or stops. When the weight is shifted to the left (driver) side, there is no effect or it gets worse.
Uphill seems to be worse than downhill.
The car does not drift to either side when the steering wheel is released when not vibrating, and doesn't have much wander even with the wheel vibrating.
It does not clunk or squeal when turning or braking.
The mileage is 115k.
View 3 Replies
I recently noticed that the airbag light of my 2001 Echo never comes on and is off all the time.
What can be the reason? Is the fuse blown?
If the fuse is blown, shouldn't there be an alarm or warning indication? I mean, because airbag is a the main safely feature in a car, shouldn't there be a warning mechanism to simply indicate that it does not work at all?
BTW, can a battery change have caused this? I changed the battery a while ago but never noticed this issue until now.
View 1 Replies
