2001 Ford Windstar, select tail lights will not function. All lights serviced by Fuse #7 have ceased to function (left rear turn lamp, right backup lamp, right stop lamp, right rear park lamp, right license lamp, left license lamp, and left backup lamp). Checked all bulbs and replaced any that were questionable but to no avail.
View 2 RepliesI'm having electronic issues with my windstar. Tail lights stay on after shutting off. All dome and interior lights stay on when ignition is on.key fob doesn't lock or unlock. Gas gauge reads empty. WHEN IT RAINS, IT ALL WORKS NORMAL. What can I do? Today, now, not starting. Turn key, not even a click. Theft light flashing. Got power and starter is good. is there a reset?
View 6 RepliesI found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 RepliesMy 99 windstar has seemed to have issues every month since it's been paid off! Isn't that how it goes....anyway,
Just recently the heat suddenly stopped working. The fan is blowing and the temp controls seem to function correctly. There is no heat coming from the front and some IS coming from the back.
What could the problem be? Blend door, actuator, motor, evaporator core?
I have a 2001 f250 v10 lariat ext cab. i was going to get wood the other day down a muddy road. My radio went out and all my running lights. i replaced the fuse radio and now the switch. Still nothing. Could it be a bad ground? i ran a jumper wire on my old switch and they worked then just stopped again. if it is a bad ground where would it be located.
View 3 RepliesHad to stop working on my car's cosmetics because the tail lights stopped working a few weeks ago. Radio, headlights, and brake lights all work.
10A fuse blows when I turn the headlights on. Tail relay is good. Bulbs and bulb sockets look good. Ground is good. I purchased an ECT2000 by Power Probe to diagnose the issue, but it's running me all over the car.
Mechanic couldn't find the issue. What should I try next?
The stop lights and the tail light of my Elantra GT 2001 (automatic transmission)won't shut off, unless the fuse is removed from its place. Is this something easy to fix? I imagine it can only be some kind of switch on the break pedal/clutch.
View 5 RepliesI'm new to modding and I've been having a really hard time finding a forum that gives a good DIY instructions on how to wire the map lights to function as the dome lights so they (the map lights) turn on when the doors are opened.
Any parts required (relays or anything else of that sort)
The rear tail lights on my truck have been out for a while now. I wasn't doing much driving at night so it wasn't much of a bother but the new job is getting me home a little later and having to drive with my hazards on is getting old fast.
My radio wasn't working either and I disconnected it a while back hoping maybe it had something to do with my lights shorting out but no luck. It remains disconnected. Just in the past few days my front running lights have went out as well.
I've tested all fuses multiple times (and replaced a couple of them) and checked and replaced bulbs. My brake lights, headlights, dash lights and hazards all work fine. I have the trailer light hook up on the rear bumper and disconnected it at the wiring harness as well hoping it was the problem but it wasn't.
I have a VW Tiguan w/ auto lights. I was just wondering if there is a way to have the fog lights turn on with the auto lights function.
View 1 RepliesI have a Ford Windstar 1999 . My license plate lights are both out. I remove the inside panel of the back door, there is a connector between the license lamps and the rest of the car electrical system. I disconnect it. I go turn on the lamps at the dash board, I then reconnect the connector to the license plate lamps at the rear door… and they work! I go back to the dash and switch the lamps (controls side +rear lamps and license) OFF and then immediately back ON, and the license plate lamps stay OUT. All the others lamps on the fuse circuit work fine. When lamps are lit, shaking the wiring harness has no effect. What is happening and where? This is very strange!
View 4 RepliesI have a 1998 ford Windstar with a 3.8 V.6 When I turn my lights on and drive it my lights flicker. I have checked all my grounds that I no of and my connections while driving my lights go dim when I let off the gas. but do not flicker any more. when I accelerate they begin to flicker again. I've had the alternator check and all is good. I have no clue.
View 2 RepliesI have a 2001 ford windstar the codes are bank 1 lean (wires have been cut) could this cause the miss fire on the #1 and 3 cylinders? The previous owner put copper plugs in it instead of platinum. How hard is it to change the plugs?
View 6 RepliesFord Windstar 2001. Auto transmission oil leaking
What I have done : Refill and observed what happen, leaking still. I changed the gasket & filter. The leaking persists.
I found bulletin service about water entering, causing ECM to give wrong measuring stick level. I fixed, according to bulletin TSB 14-06-10. It is leaking still.
There is another bulletin about the same problem: TBS 05-14-5. This bulletin is about the transaxle vent being obstructed.It is leaking a lot of oil.
Back after months...van has been checked by 2 ford dealer mechanics here in VA , nothing.
Now it's the opposite ...temp outside 90 or higher, drive it for 8 -10 ml, park and come back after 15 min. From shopping, try to start, won't idle, stalls every time I try , after 6-8 attempts, back to normal, all together 3 times, last time was so bad, had a real problem to make it back home, at every stop, it stalled.
Back to the shop ....they drove several times, no show ...it's fine, don't know what to do ????
just dies when you put in gear, comes up with a code of 1780 transmission control switch circuit out of self test range, some have suggested torque converter selonoid any way to test for these.
View 1 RepliesIs their anyway to get the tail lights to come on with the Daytime driving lights ....
View 1 RepliesIs it possible if Lexus can make it so when the Daytime running lights are on that the tail lights come on? It appears MASS has just passed a law when it is raining and you have your windshield wipers on you have to have your lights on...I leave mine on Auto and have auto windshield wipers so kinda takes away the purpose if I have to turn my lights all the way on each time.
View 5 RepliesI have a 1988 Jeep comanche I lost my tail lights, front marker lights and dash lights today I have checked all the fuses under the dash and havent found any blown I hooked a trailer up to it today and I think this is the cause some how it caused a short Can you tell me where to look for additional fuses
View 2 RepliesI have a 2001 Ford Windstar SE. 220,000 miles. A few months back it started missing ... I drove it like that just local for a few days but then I was leaving town for about a month and just parked it. After I got back I changed the plugs and all was fine on the test drive (ran perfect ... fixed the misfire). What has happened since then has been frustrating. Althought it runs great, now it stalls randomly and always when it's under acceleration and usually going up slight or a bit steeper hills (think So Cal terrain). It doesn't jerk or miss or sputter ... it just cuts out.
If you try to turn the engine over without turning the key off it won't start. Turn off the key then turn it on and it starts like nothing ever happened. No codes whatsoever. Sometimes you can drive it for 30 to 50 miles or more and have no problems at all, then all of a sudden it will stall in an area that it had no problems with over the previous week or so. It seems to stall out at about the time it wants to shift from 1st to 2nd or from 2nd to 3rd ... or at least that general rpm or accelerator pedal position. It's happened with light acceleration and heavy (pulling a long hill) acceleration. Never at idle or decelerating or just cruising on a flat piece of roadway ... never. It also seems the pedal needs to be at a constant position (not pushing down or letting up but just at a certain position under acceleration). I've had my mechanic with me 3 different times and each time it never stalled with him along. Fuel pressure was fine when he checked it (while driving).
Once in a while it will cut out (just enough to notice) then cut right back in and keep running but most of the time it just cuts out and that's it. I've changed the camshaft sensor, the crankshaft sensor, the PCM relay, the fuel pump relay, the throttle position sensor and the fuel filter. I'm hoping to set it up next week where if it stalls I can call the mechanic and have him come over to where I am and see if a code comes up (and check the fuel pressure also) without me turning it off (since that seems to reset whatever the problems is).
Twice now (and maybe a third time once I start my van again) we've had problems with the van chugging and then the service engine light blinking. Both times it happened in the past, we took it to a mechanic who said it needed a tune-up - new spark plugs, wires, etc. I'm curious as to why this keeps happening. Mileage is around 105K. It first happened last summer, second time was in December. Now it's March. What could cause this problem to repeat?
View 2 Replies