Windstar :: 1998 - No 2nd Or 3rd Gear Upshift?
Sep 6, 2014
I have a 1998 Windstar which just stopped shifting from first to second or third. I still have 1st and Reverse gear but no 2nd or 3rd. Feels like vehicle goes to neutral.
View 2 Replies
Sep 6, 2014
Advertisement
Windstar :: 1998 Not Shifting Out Of First Gear - Speedometer Quit Working
I have a 1998 windstar with a 3.8. I took my daughter Christmas shopping and noticed the car did not want to shift out of first gear. I shifted it manually to second and then DRIVE and that worked until I stopped at a light. I took off in DRIVE and the car did shift to second and third on its own but it shifted late and hard. Also, the speedometer quit working and the overdive light on the shifter just turned on by itself and then went out. By the time we got home, the SERVICE ENGINE SOON light was on. All these symptoms happened in a relatively short amount of time (5 miles). I suspect something electrical but am not sure. Is there a speed sensor fuse on these cars?
View 2 RepliesFord Transmission :: 1998 - No Upshift From 2nd To 3rd
I am having an issue with my 1998 5.4l Expedition, e4od. It will not up-shift from 2-3... It feels almost like it's in a 4x4LOW shift schedule.
I've done a lot of research, I was really hoping the fault was inside the valve body and a stuck spring or valve. I went ahead and scanned the computer and I have no codes. The O/D light does not blink. I can toggle it off and on via the button on the end of the shifter.
I watched the gear data correlate with the shifting to eliminate the cable. The reverse lights come on when in reverse, manual 1 works, reverse works, and I can get it to upshift to 2nd with manual two. In {D}, 1st gear runs until the engine is @ apprx 4,000rpm and if i let the throttle go a bit, it'll upshift to 2nd. Speed will keep increasing until the engine is screaming at 5500rpm.
It does not ever neutral out. It just wont upshift..
I pulled the TRS harness off to inspect, and I checked for codes whilst it was unplugged just to be sure I can read TCM codes. The TRS code showed up.
I tested the TPS sensor and it checks out good.
My speedo works fine and as well as my Tach.
The fluid was not low on initial check with the onset of symptoms. So, I went ahead after doing my tests, drained the pan and dropped it. I pulled the accumulator body and as well as the valve body. I could not get the solenoid off today. I will tomorrow and I will ohm it out. I inspected the valve body and accumulator body and to be honest, I do not know what a stuck valve or accumulator looks like or what it would feel like.
The pan magnet had grey material on it. I pressed it between my fingertips and it did not feel like metal. The one third to the right didnt like right at first, but I can feel a little movement when pressing it in. My camera basically washed out, but without disassembling the individual valves, they look intact via the spaces. The last one on the right is stationary..
I cannot tell if these look right (they are unaltered)
The one on the left felt like it was catching when being pressed in
What else could cause no upshift and no codes?
Golf/GTI VI :: Fifth Gear Grinds When Downshift Or Upshift
Six speed GTI Manual for those that dont know its a 2.0 TSI. Fifth gear grinds all day long when i downshift or upshift. They have given me a service car to drive around in, until its fixed. 25k on the OD and a 5 year mechanical warranty, i have 2 years left on the rest. Third gear doesn't go in easily, its like i miss third gear all the damn time, obviously its not right when the rpm's go above 3k.
View 18 RepliesLexus RC F 2015+ :: In Manual Mode Hard To Upshift When In 2nd Gear?
Driving in normal mode and the transmission in auto. Once the car gets up to temp, (usually at a stop), move the gear selector to manual mode. If you punch it, I have not issues shifting from 1st to 2nd gear, but sometimes, the up shift paddle will need to be hit multiple times in 2nd before the car will shift to 3rd.
It seems to only happen the first time I go from auto mode to manual mode during a drive cycle. It happens on my car and another car I test drove.
Monte Carlo :: Transmission Sometimes Upshift All The Way To 4th Gear When Leaving A Stop Sign
On occasion my 2001 Monte Carlo SS will sometimes upshift all the way to 4th gear when leaving a stop sign. Then it will lug & vibrate obviously from being in high gear at a low speed. I can pull over & shut car off for a minute then start it again & it will shift just fine like normal. Then randomly out of the blue it will do it again without any sort of pattern. I replaced the main computer but that didnt work.
View 1 RepliesPassat (B5) :: Slipping (hesitation) During Upshift And Occasionally Banging Into Gear During Downshift
Took my car to the dealer for it's 80K service and asked them to check the tranny because it's been slipping (hesitation) during upshift and occasionally banging into gear during downshift. I figured they would suggest the BG tranny fluid flush but got a call from the service advisor saying they found the fluid to smell burnt and it was black. 1999Pazzat V6...
View 8 RepliesFord Ranger / B-Series :: Transmission Going To Upshift Then Immediately Downshift To The Gear It Just Left
1996' Ranger with 183,000 miles. 2.3 cyl., Automatic, XLT
When I am driving and get to the 35 to 60 mph range, my trucks transmission wants to upshift, then immediately downshift to the gear it just left. It goes back and forth like this till I get where I am going, or after about 10 miles it will stop doing it. I checked the transmission fluid, and it is full and still pink.
I took it to Advanced Auto, and it blew a code of ECL Bank 1 I believe. I looked around the 'net and I think it came out to be the front O2 sensor may be bad/going bad.
Last week while it was warm enough I was driving with the rear window open, and noticed the faint smell of Rotten Eggs (this has been the only time though). Today I drove about 50 miles and basically used a quarter of a tank of gas. I am wondering if the catalytic convertor may also be going bad?
Ford 6.0L Power Stroke Diesel :: Transmission Slammed Hard Into First Gear And Sometimes Will Not Upshift
Everything was fine, running PHP 200X tune, switched to PHP 65 tow and took the 5er toy hauler on vacation last month. Pulled a lot of mountains,etc. While camping, took the truck unloaded to get fuel. Engaged tow/haul going down a mountain to utilize engine braking and the tunes "exhaust brake" and the trans slammed HARD into first gear. This happened twice. I refrained from using tow/haul. Heading home 450 miles with the 5er, I utilized tow/haul again (had it on the whole time, just like on the way down) and the truck and trans were flawless. Get home, switch back to 200X, and I'd say within a week or so, began having trans issues. Loaded stock tune, reset KAM with SCT, disconnected batteries with headlight switch on for a couple days, reloaded 200X and drove it for a couple days. No change.
It felt like the trans was slipping, not "going" like it should when on the throttle, and would sometimes not want to upshift. It would just act "weird". This would usually occur under 40 - 70% throttle (I rarely ever get on it more than that), but sometimes less. Never got any check engine light or tow/haul flashing.
So today I finally did what I should have weeks ago, took off work and ran the truck to a shop.
- First the tech hooked it up to the scanner. No codes.
- Test drove it. He said it drove fine for him. It was fine for me as well, driving it from my house to the shop (I didn't "get on" the throttle though).
- He monitored the voltage from the trans temp sensor. He said the voltage was fine, didn't spike or do anything crazy. He didn't seem 100% positive on this but, said it starts out at 5V cold and voltage should drop as the temp increases, which it did. However, the temp started out at 300 and then dropped to 200 as he was driving. #1 the temp isn't (shouldn't be) that high, and #2 it should increase while driving not drop. The temp shown on my Torque Pro app hit 149 on the way to the shop and 168 on the way home (90 degrees outside). So he seemed to think there was something screwy there.
- While driving it, his scanner showed a trans overheat (over temp/high temp, whatever) code, but no check engine light or tow/haul flash.
- Drove it home. Trans was fine until I got on it a bit and then it acted funny again. But just driving normal with light throttle it is fine.
* Thinking about trying a new temp sensor.
* Could it be in limp mode which is why it feels like it is slipping, i.e. doesn't have the normal power I'm used to?
* When the tow/haul light flashes, is it the tow/haul light on the instrument cluster? That's the only thing that lights up when I'm in T/H. Where you push the button never lights up. Assumed it was just white lettering and not a light.
1998 Windstar - Warning Light For Air Suspension Came On
My 98 Windstar Limited has air suspension in the back. Lately, it would be sitting low in the back before starting it up in the morning. The compressor would pump it up as soon as you fired up the van. And the rest of the day would be fine. The other day, the warning light for the air suspension came on, and the compressor has not worked since. Fuses and power connections all seem okay. OBD codes C1770, C1790, C1818 and C1850 were in the system.
View 3 RepliesWindstar :: 1998 Ford / Camshaft Synchronizer Bar Off?
I was removing the camshaft position sensor and synchronizer unit on a 1998 ford windstar gl with 3.8L and the synchronizer bar feel off. The bar went back into the slot and i cannot get to it. How can i retrieve the bar? I tried using a magnet. Can I access the bar from the oil pan if i remove it?
View 1 RepliesFord - Windstar :: 1998 - Transmission Failed Sometimes
The transmission in our '98 Ford Windstar has failed....sometimes. I went to back it out of the garage and the motor would rev, but no movement of the vehicle. I put it in drive and had the same results. When I put it in 2 it would move. Only in 1 or reverse is it dead. I changed the transmission fluid and filter (Fluid did not looked burned) and it ran fine. After a couple of days, same symptoms. After sitting about a week, I started it up and it acted fine. I drove it about a block. When I attempted to start from a stop sign...no movement. I put it in 2 and drove away.
View 3 RepliesWindstar :: 1998 3.0 - Drop In Revs Causes Engine To Stall
My wife has a 1998 Windstar 3.0
Prior to going out yesterday, I noticed that the van seemed kind of 'jumpy' when idling - the timing was a bit sticky and inconsistent and kept seeming to try and right itself. I stuck the accelerator down and it ran perfect when it was getting gas but started 'stagering' again when I took it off.
So my wife went out to walmart - a 30 min drive (we are in the country) - and all was good till she was turning the corner into the parking lot and the engine stalled. It was your standard stall - power steering went out but all other electrics kept going etc etc.
She sat there for a minute - put it in park - then fired it right back up again. After running into walmart, she just drove home as fast as possible to reduce the length of time it had to happen again.....
So while there are, Im sure, a plethora of possible issues - I was wondering about the IAC value? How could that be responsible for the parking lot though - doesn't it only act when the car is stationary?
The sort of thing was happening about 3 months ago, and I ran seafoam through the fuel - which seemed to work for a while.
Windstar :: 1998 - No Vacuum To Rear Auxiliary Unit
1998 Windstar Limited. I have no vacuum to my rear Auxiliary Unit. I am considering buying a hand vacuum pump. However, I never used one. Is there a video available.
View 9 RepliesWindstar :: 1998 - Moderate / Slight Jerk When Stopping
My windstar has for a while been making moderate/slight jerks when stopping. It tends to happen typically just before coming to a complete stop, although sometimes it happens during low-speed turns when coasting (also sometimes have the issue where it shifts downshifts harshly after a "sweeping turn," as mentioned in one of the windstar TSBs). The RPMS don't appear to visibly drop when it occurs (although the tach in the 'stars seems a little slow sometimes). The only trouble code present is P0133 for the Bank 1 downstream O2 sensor slow response.
Also, it tends to worsen when the car is warm. The jerking is less severe when the engine is cool, and tends to worsen after the car warms up. Also it sometimes almost feels like the jerk occurs in two stages. I do not believe it is the TCC solenoid failing to disengage, due to the fact that it even happens if I get up to 15mph for a hundred feet, and then stop.
Probably unrelated, but the car also tends to run rough for 10-15 seconds after starting the first time if left sitting for a few days.
Windstar :: 1998 - Oil / Moisture In Throttle Body And Air Duct Hose
I have a great running 98 Windstar. It does not overheat. The oil looks like it needs to be changed but it is not Coffee Colored, as the picture. The PCV valve looks clean, and rattles. I replaced the small 2 inch hose at the PCV valve on the back valve cover since it looked weak in the middle and may have been collapsing. I no longer get the big puddles of OIL/WATER on the ground, that I use to. I cleaned the oil/water out of the Intake Hose of the Throttle Body, but I still see some of the mixture underneath the Air Instake hose after a long drive.
I will go by the Ford dealer and buy another PCV valve, and replace the small curved hose going to the top of the engine near the Throttle Body that the other end of the PCV connects. Someone suggested that this could be cracked, and it does have some small cracks in it at the bend.
I have read that the 99-00 had a design problem with the Valve Cover, and it allowed oil to be sucked out and give similar problem. But since this is a 98, I am just looking for pinched hoses, or leaks. Car runs great, and hoping that I can find the reason that oil is being sucked into the air intake.
Do I have it correct that during normal operation, that the moisture and gases are sucked up out of the engine thru the PCV and into the top of the engine. And that the other Valve cover hose is going in the other direction or from the throttle body to the Valve cover?
Just trying to determine if the oil/moisture mixture is coming from the front or rear (PCV) valve cover. Getting no codes on the engine.
Windstar :: 1998 Ford V6 Lights Flicker When Drive Or Accelerate
I have a 1998 ford Windstar with a 3.8 V.6 When I turn my lights on and drive it my lights flicker. I have checked all my grounds that I no of and my connections while driving my lights go dim when I let off the gas. but do not flicker any more. when I accelerate they begin to flicker again. I've had the alternator check and all is good. I have no clue.
View 2 RepliesFord - Windstar :: 1998 - Start Running Rough If Throttle Is Slightly Cracked
From cold, I start the van up, and if I just slightly crack the throttle it will start running rough. I think it goes away under heavier throttle...might just be that the rpms are up I can't feel it anymore, I don't know. It will idle just fine, and after it warms up it also seems fine. Where to look?Also I sometimes hear a very small, high pitched, vacuum leak from under the hood. What are the most common items that go bad, that I should look at first?
View 4 RepliesFord - Windstar :: 1998 - Code P1538 For Intake Manifold Runner Control
I have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?
View 14 RepliesFord - Windstar :: Gear Shifter Does Not Engage Properly
Our cars shifter does not engage properly to Drive position. It comes down to D but the car just revs up or does not pick speed when we hit gas. we have to adjust/move it up and down to engage it. other position seems to be working fine. what could be the problem?
View 6 RepliesWindstar :: 2001 Ford Dies When Put It In Gear - Code 1780
just dies when you put in gear, comes up with a code of 1780 transmission control switch circuit out of self test range, some have suggested torque converter selonoid any way to test for these.
View 1 Replies