My 740 (1990, B230E, non-turbo) has been running rough at low rpm. Once above 1800 rpm or so it's fine. I've changed the Distributor cap and rotor arm (they were both shot), but the problem persists. I'm thinking injector relay or ignition stage amplifier next, but I don't want to just through parts at it.
The plugs were changed 3 months/1,500 miles ago. The misfire is intermittent.
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
I have a 2005 XC90, 2.5T with about 210K miles.
The issue began while driving at about 70mph on the highway. The car acted like it was running out of gas, skipping and hesitating. After getting off the highway the issue persisted. Accelerating from a stop caused the car to once again act like it was running out of gas sputtering and lurching. The CEL came on and it stalled once before getting to an AutoZone. The codes came back as P2177 (too lean off idle bank 1) and P0089 (fuel pressure regulator).
I limped home and parked the car for a few days to check out my options. After a few days the car drove perfectly with no issues. But the issue returned the same as before within a few more days. So here's what I've done thus far....
1. Replaced the fuel pressure sensor (no change)
2. Replaced spark plugs (no change)
3. Replaced fuel filter (car ran perfectly for a few weeks, self clearing the CEL)
4. Ran some Seafoam cleaner through a tank of gas (car continued to run fine)
5. A few days ago the issue returns, same as before
6. Cleaned MAF (no change)
After replacing the fuel filter and running the Seafoam it ran great. Then all of a sudden it's doing the exact same thing again.
I've scoured the web for more info but come up empty handed. My thoughts now lean toward the following...
1. Leak in the turbo system or TCV issue
2. Bad injector(s)
3. Bad coil(s)
4. Failing fuel pump
5. Random O2 sensor freaking out
First time Volvo owner. Love the 97 850 that I got, but it runs really rough, and I don't know if that's normal for these cars or not. When I say it runs rough, I mean that it vibrates like crazy (not shaking, but vibrating) and it's loud. Every other car I've owned sounds smooth when it's idling or accelerating, but not this one. And I don't mind the noise at all, but the vibrations are a little frustrating.
View 3 RepliesI have a 2003 Volvo S40. I just replaced the battery, spark plugs, coils, fuel filter along with a fuel system flush. Because the car was running very rough. It's been 4 days since i got it back from the shop and now my car won't start unless I give it gas. The car won't stay on and it smells like it's running very rich.
View 1 Replies2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
Motor seems to burn out spark plugs every month. I was using non volvo sparks. I took car to Volvo dealers and repairers who gave car a diagnostic check but nothing showed up. They told me to use Original Volvo Spark Plugs which I did. The Car went great with no problems for about 3 months thinking problem was fixed. Low and behold the same problem came back.
I changed spark plugs again (original Volvo) and car only ran for 10 ks and then ran very very rough with no power. Motor felt like it was running on a few cylinders. It seem this problem happens mostly in hot weather. Motor also heats up but when cooled down runs well again. I intend to buy new rotor Bosch and Distributer cap and if needed coil.
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 RepliesI have a 2000 excursion 4x4 v10 with 90k. The past few months I've noticed a tug or miss fire at low RPM (2000 AN UNDER) the past week its gotten worse, some occasional rough idol and the missing is getting worse. Whats wrong?? I don't want to take it to ford yet! No Check Engine Light yet...
View 14 RepliesI have a 1990 3.1L, multiport fuel injection (NOT sequential FI), which runs very well most of the time. However, when I cold start it runs rough (misfire) for about 1 minute (no throttle) or until acclerated. The is no misfire when running normal, but it might be running a little rough when stopped at a traffic light (in Drive, foot on brake).
I put new plugs and wires on, but it did not affect this problem.
I am not using coolant, or oil, the plugs that were removed were somewhat worn, enough that I expected to notice a difference after they were changed.
I have not yet (1) cleaned the MAF, (2) checked carefully for vacuum leaks, (3) checked for leaking injectors.
Since this is a 1990, OBDI, I can't say which cylinder is misfiring or how the fuel trims look etc.
When I'm driving and get above 50-60 I will get the Check Engine Light. Check the codes It shows 6 ---300, 303, 306, 300, 303, 306. When I slow the car down it is running rough, almost like it has a miss.
I reset the computer while this is going on and the engine smooths out and it runs correctly until I keep my pedal down and then it kicks the exact same errors.
Here's strange part number one: Once I get down to about a gallon or two of gas in the car everything seems to run fine. I have plenty of power, no codes and the car runs fantastic!
Strange part number 2: Very occasionally When I get in the car in the morning to go to work, the car is a bit difficult to start. When it finally kicks over, it is immediately running rough. resetting the computer with the engine running does not seem to stop the rough running. If I turn off the engine and let the car set for a bit it will start and run fine, with the exception of the first problem mentioned in this thread. There is no code while it is running rough, but when the Light kicks on as per the first issue mentioned, I have an additional code -- 335. This car has been excellent up until the last few months when this issue developed.
In your experience, what issues have you seen that caused intermittent rough running at idle, but did not throw a code. I have monitored (with numerous scanners/gauges) this 6.0, but cannot get a code or see any of the sensors out of spec.
At Hot idle:
IPR: 24.2
ICP: 640
ICV: 0.90
MAP: 14.7
MAF Volts: 1.5
EOT/ECT Deltas within 10 and Avg ECT=192, EOT=199
EGR Valve cleaned and EGR demanded = EGR Measured
Vehicle will run rough after long runs or towing. Cylinder Balance test showed all injectors on. What could be the cause?
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 RepliesOkay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
My 1996 S10 2.2 liter pickup has been having some 'issues'. Truck has been kind to me over the years, but now is running a bit rough. It has an irreguler idle and continues to run this way through all speeds. The blinking code reads "cylinder 1 misfire". I did all the basics. I changed the plugs and wires, ignition coils and fuel filter. Here is where is gets tricky, after changing the fuel filter, it ran great again. Then it started to run rough again later that day. I thought I somehow clogged up the new filter, so I removed the new one for inspection. Realizing there was nothing wrong with it, I reinstalled. Truck ran great again. Went out to drive it to work a couple hours later and it started fine, then after about 10 seconds of running, it went back to the rough idle.
View 19 Replies98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......