Volvo :: Replaced The Brakes But Pedal Still Spongy
Jul 13, 2013
My 89 240 is a project car so I am just fixing everything up as new until it's all done.
Replaced the Brake Booster with a fully reconditioned one, a new master cylinder, full pressure bleed, new pads. Now I have fantastic brakes but they feel super spongy still . As an example, I make an emergency stop to check if they are ok and after stopping just fine , the pedal still wants to go down further. I have checked all the flexible lines for ballooning and they are ok .
View 9 Replies
Advertisement
I just replaced the front break pads. I didn't replace the rotors or get them machined, didn't look like they needed them. Once I pushed on the brakes (truck off) I noticed that brake fluid spilled out the brake reservoir. I'm guessing it happened when I compressed the piston into the caliper? I took some of the fluid out of the reservoir and now its at MAX (I didn't bleed them). I've only been only be able to stop and go on the driveway (I'm waiting on a new radius arm bracket). The brakes seems spongy, the brake hits the floor. ABS and Brake lights came on then turned off once I started to pump them when I turned the truck 'on'. Do I just need to actually drive and "break" the breaks in?
View 2 Replies
I have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 Replies
I've got a '12 GTI (bought 10/1/12) with just over 20k miles on it. Everything on the car is stock and original - pads, rotors, calipers - and the brake fluid hasn't been flushed yet. The last few months I've noticed an increasing sponginess to the brakes, the pedal taking longer to depress before I feel significant stopping.
Pads and rotors still look good. Fluid level's normal. At best it feels like maybe some air pockets might've worked into the fluid lines. At worst it feels like maybe a leaky master cylinder. I'm wondering if it's a common problem.
View 1 Replies
I'm not exactly sure what's going on but it feels like I'm missing some brakes - the pedal is extremely spongy, I have to push it nearly to the floor. And when they do engage, it isn't with the same vigor as they did before.
It's strange, it just sort of happened - I drove to a friend's house, everything was fine. But when I left all of a sudden, there's this problem.
It's not like the pads have come apart and destroyed a caliper - I had that happen to me a few years ago and I definitely felt it happen, plus once it did I lost almost all braking ability as the lines would just leak fluid.
View 2 Replies
I've been in some version of a Volvo since I inherited my parents brick-colored sedan in high school. It was a tank, ran forever and kept me safe and protected. Years later I bought a new black Volvo sedan. In 2006 with a hubby and two kids, I decided that I could graduate to the SUV. Feeling like I'd made a fantastically safe and practical decision, I drive my silver XC90 to work and on road trips. It's not the fanciest nor sexiest vehicle, but I feel my family is safe.
Hard working folks should not have huge budget surprises like my Volvo SUV has turned into. Little did I know what I was getting myself into when I made this purchase. When I took it into the Culver City dealer for my 30,000 mile service yesterday, I found out that my Volvo XC90 needed it's second replacement rotors and brake pads. I'd already been through this expense at 17,000 miles, much to my surprise. I'd never heard of needing to replace brake pads and rotors at 17,000.
Now, at 30,000 miles the local dealer's service department told me I needed another set at a cost of $1,000.
I have friends driving a Toyota or a Honda that rarely require maintenance or repairs. Volvo is an expensive vehicle to buy and it gets you every time you visit the service department and all repairs are expensive. It's disappointing to say the least.
View 17 Replies
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies
I'm not too familiar with these trucks, but I've been working on my buddies 1999 e350 ford van.
The other day we were going out kayaking, and the brakes locked up, we were able to drive it home, but it was obvious the brakes were holding the truck back. decided to check it out today, found one front and one rear caliper were sticking, the dual piston calipers only had one working, which I believed to be causing the pads to get pressed together crooked, and caused them to "lock up" or get stuck.
anyways, got the new calipers on and no more sticking, so I bled the brakes started in the front and went all the way to the back, did every caliper. brakes feel firm with the vehicle off, but instantly when the van is started, the pedal goes to the floor. it still stops okay, but the pedal feel is not nearly where it should be.
I got all of the air out of the system, but the abs light is on, and has been for a while. I'm wondering if there is something else that needs to be bled in the abs? someone was telling me about bleeding the abs motor?
View 14 Replies
My dad drives an '06 Sonata. And he recently broke a brake line and had gotten it fixed. His current problem is that his brake pedal hasn't returned after getting the line fixed. What can he do to fix that? The pedal is really low and is spongy. And his ABS and ESC lights are also on.
View 4 Replies
I have a question about the bleeding the brake? When I washed my E, I usually spray the wheel and the brake part. I don't know it is a good idea or not. Recently, I felt like I have to step further on the brake pedal to apply the brake.
The force is there and Brake assist is still in effect if I step fast enough. I just felt like the brake pedal is spongy. My E is on 36k right now. Do you think wash the wheel often will cause the problem to brake line?
I have confirmed that my Gf's Elantra is easy and ease to brake than mine. At the mean time, her brake fluid is darker than mine. My brake fluid is full and clear. Maybe I should not wash the wheel more often. Or maybe I get OCD too much?
View 22 Replies
I have a 2000 Silverado 1500 replaced calipers, master cylinder, and ABS Pump/Modulator. Bled all four calipers. Brake pedal spongy and has very little pressure and travels all the way to the floor. What am I missing here?
View 8 Replies
I just finished replacing pads, calipers, rotors, wheel cylinders & brake drum hardware on my truck along with flushing the brake fluid. The brakes work but the pedal goes almost to the floor. While bleeding them some air did come out as expected. But a couple times the master cylinder reservoir got very low on fluid. The workshop manual talks about bleeding the MC but are special fittings needed for that?
View 10 Replies
A while ago I had to lock up my brakes to prevent an accident. now my brakes are soft and spongy, going all the way to the floor and still not quite stopping. making abs type noise. also, i can press all the way down while standing still, with the same type noise.
1996 chevrolet astrovan
View 3 Replies
Friday morning I'm backing my 2011 Sonata Limited out of the garage and I always idle out but this time it started backing about 2 paces faster than idle speed. I hit the brakes and the pedal is on the floor..no brakes..I put it Drive and nothing no power. It didn't stop until I backed into the street curb, tires only no damage. When it hit the curb the brake pedal was back and Drive engaged as if nothing ever happened. Dropped it off at the dealer and they couldn't find anything but did open a case with Hyundai. Saturday doing a couple of backing the brakes were really spongy in reverse only. Will have that checked next week.
View 17 Replies
Drove the lady's car out on some errands today and ran into a problem on our drive home. Car was pinging really bad (low rpms in 1st and second) and car seemed as if it couldn't get out of its own way. Was driving for some time on the freeway (after a blistering 0-60 time of 20 seconds ), and noticed that the brake pedal was really spongy (felt like a mk1 when you try to brake with the car off). Found that the e-brake handle was up (negligibly up (perhaps 1mm raised)). Didn't have power brakes at all and had to use a lot of engine braking to slow the car off of the freeway.
Rear of the car smells like copper (wet pennies) and found that the brake reservoir is cracked (but fluid still at max level). Also noticed that as of late, when the car is at a stop (sometimes in gear, and sometimes in neutral) the car will rock/bump a little almost as if someone were giving it a bumper kiss with their car.
View 2 Replies
My Gen I Prius is screeching at me with the BRAKE and ABS lights on, and I hear the electrically actuated pump pulsing as it tries to get pressure into the system. The pedal is spongy and will go all the way down, with the right amount of exerted pressure from my foot.
View 6 Replies
So I've got spongy brakes on my 2003 Prius. I've flushed the whole system twice. Replaced the hoses, pads, rotors, shoes, and drums. Still spongy. I'm not sure what to check next. No lights or codes. I'm leaning toward the master cylinder. You can pump the brakes up when they become spongy and they hold solid. If you practically stand on the brake pedal it will slowly bleed down. This tells me the fluid pressure must be escaping somewhere. I don't want to just blindly replace parts.
View 3 Replies
After replacing the Front Rotors, calipers, and brake lines on my 2005 F150 Super Crew I have spongy brakes. I have also replaced the master cylinder. I have bled the brakes as well as a reputable repair shop has done the same. We are both at a loss as to what is wrong. The ABS light is on now after the replacement of these parts. This issue did not exist prior to changing these items. This was done to hopefully eliminate brake shudder that I have been experiencing for some time.
View 4 Replies
After my local brake shop changed the front rotors and brake pads on my 99 grand cherokee the brake pedal is spongy and long, almost reaching the floor. They don't know why. Apparently they had a problem with fitting the new pads. I took it to the jeep dealer and they told me the master brake cylinder was leaking and needed to be replaced. many hundreds of dollars later the brakes are still spongy and long and does not correct with repeated pumping. The dealer was also stumped and I complained that nothing changed with the new master cylinder. what might be the problem?
View 4 Replies
I have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 Replies
In cold weather (10-15 deg.) the brakes in my 2009 Santa Fe are very soft/spongy. I had to depress the brake pedal nearly to the floor before it would stop on dry pavement. Once it's warmed up, the brakes seem fine. Pumping them seems to work but they are not back to their normal condition.
View 14 Replies
