Volvo :: 740 Turbo Wagon Cuts Out While Driving When Engine Reaches Its Normal Temperature
Jun 13, 2010
My 1989 740 Turbo wagon cuts out while I'm driving. It only ever does it at about the point when the engine first reaches its normal operating temperature. It can cut out while idling or when driving at normal speed. I'm not sure if it's related to temperature or time (it usually cuts out at about the 5-8 minute mark), or if this is simply coincidental. It does it nearly every day.
It's definitely caused by the fuel pump relay cutting out. I've replaced this already, with no improvement. Something is causing the relay to suddenly lose an input.
Once cut, it takes a few quick flicks of the key to the START position for the fuel pump relay to receive power again. It will then drive faultlessly for the rest of the day. Although, if allowed to sit and cool for many hours, it will sometimes do this again.
View 7 Replies
Advertisement
I just got my 1996 volvo 850 turbo wagon running, after I replaced a valve, lapped all the valves and replaced all valve stem seals/full stage zero(timing belt, plugs, wires, cap, rotor, thermostat). Boy was she a strong runner, for the whole day it was running. I do admit to abusing it quite a bit. But what else would you expect from an 18 year old kid who just rebuilt his first volvo engine ? Now, i will note that the car had horrid previous owners, that took no care of the car(ran it low on oil and who knows what else). I know I ran it out of oil once, on the way home from buying it.....the guy did not put the oil filter on tight enough, and it blew the oil filter seal out. Luckily volvo's have low oil sensors. after i rebuilt the top end my engine was throwing out blue smoke for a while, but i thought it was just a bad turbo bearing.
Anyways, to cut to the chase; My engine sounds like this one. [URL]......
I did a compression check, all cylinders at 180 psi. all my lifters look good. I had a few plugged oil passages in the cam cover, but none that go to the lifters. i pushed on all valve springs, they look good. i used a screwdriver and hammer to check if the valve guides pulled out, and the valves are solid in place. I was still making boost even though the engine was knocking like this, so i know its not a rod bearing, because the knock sensors would have picked up on it and dropped the boost.
View 2 Replies
I am new to my car. It is an '95 turbo wagon with a 5 speed conversion and a ARP orange ECU. The issue is the car is holding shift rpm for 4-5 seconds after I take my foot off the gas. Since I am taking the load off the motor when I clutch in, it actually climbs higher before it drops off. Needless to say it is not really drivable in traffic that way! The idle rpm is ok and the car pulls really well when accelerating. I have checked for vacuum leaks and I am heading for the Idle Air Control valve. I don't think the engine has any other mods and it is pretty high milage (188k).
View 1 Replies
I'm a newbie who just took ownership of a 1982 turbo wagon. It's been sitting a while but started right up and ran well for about 20 miles until it began stumbling on acceleration.
The car starts easily and runs smoothly until it gets hot and then it suffers severe hesitation and stumbling. Occasionally it will stall but starts right up again. It has never failed to restart immediately.
On a cool day, it will run smoothly for thirty minutes or more before the problem begins. On a hot day, the problem begins in five minutes.
View 4 Replies
I have a 1994 Volvo 940 non turbo wagon. I just started having issues with the brakes lights and taillights not working. I have checked all the fuses visually and also did a continuity test on each one found all the fuses were good. I have replaced the all the relays, I have replaced the large red relay ( bulb failure relay ) and even did a continuity check on the bulb failure relay pins that are specifically for the rear brake light, everything checked out fine. I hesitate to change the brake light switch because the third brake light is working fine. I have considered replacing the headlight switch due to the taillights won't come on when the lights switch is on. My headlights do work though. There is no light on the dash indicating a bulb is out now since I replaced the third brake light bulb.
1994 Volvo 940 wagon
Non turbo
View 7 Replies
My 1996 Volvo 850 Turbo Wagon died in the middle of the freeway last night without any warning...I was driving it home after purchasing it from a private seller who is completely ignoring me now (of course). The car ran fine on the test drive and fine for the 40 or 50 miles on the way back home and then suddenly stepping on the gas did nothing and I had to get off the road immediately. I'm 8 months pregnant so needless to say, I was extremely freaked out.
Anyways, I had it towed home. Today I went out and started it and it was a little bit hesitant but it started. The RPMs were bouncing around below 1000 and the car sounded like it wanted to stall but didn't.
I read online to start it and turn the AC on see what the RPMs do and that this can diagnose an idle control valve that needs replacing. I went out and started the car again, blasted the AC and now the RPMs were staying steady at 1000 and the car no longer sounded like it was about to stall. The RPMs did shoot up passed 2000 once shortly after turning the AC on. I'm assuming this must mean that the idle control valve needs to be replaced.
Someone else had posted about their car (same model/year as mine) would die unexpectedly and in their case it turned out to be the mass air flow sensor. I am really wondering about the fuel pump, fuel pump sensor / relay.
View 1 Replies
My 94 850 turbo wagon starts rough and idles very high. the rpms dont come down. After turning car off, wont restart again unless I let in sit for a while.
View 11 Replies
I recently bought this car in its current no start condition after sitting 3 years. Initially I jumped it off and it just cranked, no attempt to start and no noise from either fuel pump.
I checked the fuses and the fuel pump relay behind/under the radio and it clicked and was dated 2006 so it had been replaced. I assumed it was replaced when the under car fuel pump was replaced at it was a replacement.
I sprayed a little starting fluid and it fired right up and ran until used up.
I ordered both pumps and strainer and installed the under car pump earlier this week. The in tank pump and strainer looked horrible and original. There was a small issue with the return line on the in tank fuel pump sending unit when I removed it that required brazing which I got back from the shop today.
This afternoon I installed the in tank pump & strainer on the sending unit and installed all that stuff. I spliced in a quick disconnect in the wiring harness for easy separation/installation next time.
Jumped the car again [yeah needs a battery] after everything was hooked back up and no in tank pump heard with key on to prime several times and no start although I hear the under car pump quit after attempting to start and they turned off.
Is there any other fuse/relay to check? If the under car fuel pump is evidently working, wouldn't it pull fuel without the in tank pump coming on? There's about 3 gallons in the tank. I'm going to test if there's current to the in tank pump tomorrow.
View 8 Replies
Since I bought the car I noticed my temperature gauge has never even touched the middle mark on the instrument panel. Is this normal or is my thermostat hung open?
View 4 Replies
I have a 1992 850 Estate (wagon) which has been making a funny noise when driving. I cannot locate it. The noise only happens when driving, I have never herd it when stationary. Most often when cold but not exclusively. I have examined all the items attached to the engine driven by the serpentine belt all run smoothly. The belt was changed just after I bought it.
I have checked the wheel arches to see if the tyres rub but no. The suspension is fairly new with new anti-roll bar links fitted for last MOT. The noise sounds like a dry bearing and is a combination of a rub and a screech, there is no loss of coolant but I suspect the water pump or one of the tensioning rollers to be at fault. The last owner told me that the belt had been changed a few months before I bought the car (off Ebay) but he did not say anything about the rollers or water pump and I did not ask.
One other point is that when I bought the car I had to add a full 5 litres of oil to the sump due to their being no oil on the dip stick. Since then the engine has run well (good engineering) but this noise is happening and as I have said it is driving me nuts.
Attached File(s)
volvo_011.JPG ( 588.86K )
volvo_008.JPG ( 530.3K )
View 5 Replies
I just bought a volvo 240, cuts off and stalls while driving. Wondering what hose this is.
View 1 Replies
I drive a 92 Volvo 240 with under 100,000 miles on it. Previous owner never really drove it, had it for about four years now. During the winter we seem to have electrical issues; back in 2009 I turned the car on after going shopping and drove immediately, while driving I got a green light and was braking around the corner the car just cut out completely. Got it to a mechanic and they replaced the whole electrical system, issues never reappeared for another two years. 2010 only issue was it need a new transmission, so I put in a used one. Four months later, February I believe, this time it would not start at all and it was night time. Got it towed to the mechanic and the next day he called me, said nothing was wrong with it started right up.
Now we are here November 22, 2011 and the car has cut out on me twice in the pas week. The first time was a dark cold night, got it towed to the mechanic and started up the next day like nothing was the issue. The mechanic joked that it likes to play dead and it starving for attention. The second time it was in broad day light and it started about again 30 minutes later.
3 out 4 times my car cut it happened while applying the brake and from a short distance from where it was parked. Also note that during the night during the winter the battery light will have a light glow to it, also when purchased the owner put it a newer radio system, sometimes when the brakes are applied it will cut out, during the winter is when its more common.
After it happened a third time and the mechanics were stumped, I decided to go to a much reliable source.
View 6 Replies
My 1988 240DL wagon....the engine temp gauge is not working? is see the wire that goes to the sensor in the engine block, it is there and connected to the sensor. is there a way to test the wire? I have purchased a new sensor, but I have not replaced it yet.
View 1 Replies
I have an '89 740 wagon, Bosch ignition. It will not start. If I spray starter fluid, it will fire, then immediately die. I have replaced already both fuel pumps, noise suppressor/fuel injector relay, fuel pump relays.
I installed a fuse in the fuse box, which was empty when I purchased the car. And the engine instantly died. It did start up when the fuse was removed, and I drove it back across country. The idle got worse until it died and would not start back home.
View 1 Replies
We bought a new 2012 Volvo XC 70 wagon. It only has 6,000 miles on it and the Check oil light has gone on three times. Each time it has required approximately one quart (which the dealer claims is "within specs" for this engine). I believe it satisfies the lemon law criteria in PA since it has been back to the shop three times in less than a year. Should I insist on a replacement or is this "normal" wear for this car.
View 19 Replies
Its a 2002 Santa Fe 2.0 turbo diesel. When driving the engine will suddenly cut out. Its as though the ignition has been turned off, there is no hesitation or warning, it just shuts down.
This is what has been done so far: New high pressure fuel pump fitted by main dealer in June. My mechanic has fitted a new high pressure fuel sensor, new low pressure fuel pump (at rear by fuel tank), changed relays around, checked all fuel injectors (found in good condition) and checked various connection plugs and wiring. At motorway speeds the engine will not cut, its only at lower speeds. When it cuts the EML comes on with a 'Fuel Pressure Fault' code. Sometimes the light doesn't come on. Sometimes the light comes on but will go out the next day. When the engine cuts out you have to wait 20 seconds before it will re-start. If you try to start before this the engine will only turn over without firing. The car has only done 79000 miles. The main dealer gave up and said they don't know where the fault is because the code is not specific enough.
View 6 Replies
I have a VOLVO S40 with mileage of about 122,000 km, engine and transmission models were B4204S, MPS6. The car water temperature suddenly down during driving. Connect the VIDA DICE to read the relevant fault codes, just only one: "ECM-0118 engine coolant temperature sensor, signal is too high, B420S3 0" according to the fault code, the least can exclude network CAN line, because in the communication control unit.
View 1 Replies
I've got a 2003 Volvo S60 with close to 121,000 miles on it.
Last winter, my Engine cut out on me as I was taking a sharp right onto my home street. At first, I thought I hit an icy patch and my car had skidded, but then I realized the engine was off, but all the lights on my dashboard were on (including all the warning/alert lights). I put the car in park, turned my key into the off position, then tried to start it up. It immediately started. Other factors: There was snow and I had just recently exited the highway.
Everything seemed to be going pretty well until this winter (in Connecticut) when my car cut out on me again. Just like before, I assumed I had hit an icy patch as the car seemed sluggish and unresponsive (and it had just snowed). Again, it happened as I was taking a right turn, and it's happened about three times since.
Today was the first time it happened as I was making a left turn. Luckily, I was the last car in the turning lane, and I managed to get my car more or less close to the shoulder and put my hazard lights on (as traffic was now approaching), and Nik Nak rebooted just as before.
I used to think the cold/snow had something to do with it, but it was 50 degrees today. Also, I'm not entirely sure, but I think the wheel may have been turned as far as it could go. I honestly can't remember if that was the case the other times it cut out. I plan on experimenting in a parking lot tomorrow to see if turning the wheel all the way is causing it.
What might be causing it? (And besides not turning the steering wheel all the way, how this problem may be fixed?)
View 6 Replies
Sometimes, when the engine is at normal operating temperature, it won't start up when I turn it off. For example, let's say on my way home I stop off in a supermarket to pick up some stuff. I'll come back out 20 minutes or so later, only to find out my car isn't starting. I'll turn the key and the engine will crank, shake and then immediately die on me [I'm under the impression the engine isn't even starting at this point because tapping the gas does nothing]. Again, this is a problem that is only happening sometimes. I can do the same routine tomorrow and it'll start up flawlessly.
1) This is only an intermittent problem. The problem doesn't seem to be occurring more frequently, but when it does happen, the engine is harder to start. For example, the first time this happened to me, I got it started after one or two tries. After my latest episode, it took me 11 tries to get it running!
2) After the engine does finally start, the engine will run really rough and shake a lot until I tap the gas a few times (which is leading me to believe this is some sort of fuel related problem [sometimes, the engine will start on one try, but will run rough until I tap the gas a few times]).
3) When the car is cold, it starts up flawlessly every time without fail.
4) The car runs mint! No hesitation or otherwise stalling, etc.
What I've done so far to try to remedy the problem:
1) Changed spark plugs
2) Fuel line cleaning/flush
View 7 Replies
During the summer, my Celica runs just fine. Now, the temps are as low as the single digits outside (Fahrenheit). While I'm out driving, it can easily take 30 mile or more miles of driving before the engine finally warms up to the normal operating temperature, according to the dash gauge.
My mechanic is quoting me $135 or so to replace the thermostat. I haven't heard of thermostats getting stuck open and resulting in "under" heating conditions too often though.
Any thoughts on what the likely cause of this cold engine condition is? My gas mileage has also taken a good sized hit. Lost 5 mpg or so.
Can I just put a piece of cardboard in front of the radiator for the winter and call it good?
View 3 Replies
My 2001 1.5l works fine when cold however once it reaches temperature it will hiccup and then stall! It WILL NOT fire up until it gets cold again. Usually happens when we are coasting to a stop. I'm not a mechanic but can am mechanically inclined. I brought it to Autozone and had the computer codes sent (yes check engine lt was on) One code was a fuel lean code. Cannot recall the exact number. When it act up it sounds like there is either no fuel or no fire. I cleaned the mass air sensor and put fuel treatment in it and I replaced the fuel gas cap.
View 1 Replies
