My van stumbling upon acceleration. Well now I am getting the following codes and the van barely has enough power to move. The codes are: P1860 Enhanced: Tcc Pulse width modulation sol ckt electrical, P0758 Shift sol B ckt electrical, PO755 Shift Sol B malfunction, PO740 TCC ckt malfunction
View 7 RepliesI was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 RepliesI bought a gorgeous red 4.0L V-6 Mustang very cheap last week because it needed a clutch. I would not even pull the car. Little did I know that the clutch kit, including the slave cylinder and flywheel, was over $600. (But that's another story.)
The car runs now, but will not go over 3800 RPM in any gear. It had NINE codes, which they cleared. I was told that they primarily pointed to the MAF sensor. I cleaned it with the recommended aerosol. I have driven it 20 miles, and the MIL has not returned, but the little wrench symbol has. The Manual says to take it to the dealer (of course). The car seems to run fairly well, with the exception of the low rev limit. It is a "fly by wire" set up, with electronic throttle.
The cleared codes were P0102, P0113, P0135, P0141, P0155, P0161, P0403, P0443, and P0446. They actually repeated on Autozone's scanner. (My six year old Actron won't link to this car for some reason.
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 RepliesMy car is a Prius Plus 2012.
One day, I decided to go to a mechanic to clean the EGR pipe. Only the pipe, not the whole EGR. It was an extremely simple operation a mechanical one, not electrical etc. Starting from that day, when I go with the car, from time to time, check engine lights up. For a fraction of a second to up to 2 seconds then it disappear.
The car behave itself without a problem. But still the on-off check engine is really annoying.
So a went to the dealer. Put the car on tester.
Result: no code error !
I went to another garage , put another tester on the car, no error..
How can I actually see what the error is if nothing is stocked in the ECU of the car?
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
I tested my new VCDS today a HEX-USB+CAN. I got CAN: Not Ready. But that's impossible.
My guess is that the OBD2 interface I got is faulty.
In the past few weeks I have seen an intermittent "Level Error-Workshop". However every suspension function has worked perfectly, and no height was lost even while sitting at the airport for a week.
How to track down the leak. I can see a tank pressure of about 13 PSI. Is that about right. I did a raise / lower while VCDS was connected and there was a pressure drop to about 11.7 PSI but no level error. What is the correct range of tank pressure settings?
Address 34: Level Control Labels: 3D0-907-553.lbl
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0005521
Shop #: WSC 01065 000 00000
VCID: 2757057592F60B6
1 Fault Found:
01583 - Leak in System Detected
000 - - - Intermittent
2005 with 123,000 miles. I have owned for a few thousand miles. Car was dealer maintained at every recommended interval. Car runs perfect.
After car sat for a week or so, I drove it and the red triangle popped up along with PROBLEM statement and take to immediately to dealer symbol. Red Triangle and other warnings repeats every once in awhile - will go a day without, and then will come on and off within a couple miles. Car continues to run fine. There are no other check engine lights. I have checked all the fluids and they are fine.
The battery charges fine, and holds the charge overnight. I have a generic code reader and there are no codes. I have read other posts, and there are always problems that seem to come with the Triangle. Gas mileage is fine as well.
Not real familiar with this code, given that my check engine light came on a couple weeks ago and they detected some errors and these codes appeared.
View 2 RepliesHave a 2000 Passat V6 5spd. Recently ran the codes, and this is what I came up with under engine.
9 Faults Found:
17833 - EVAP Purge Valve (N80): Short to Ground
P1425 - 35-10 - - - Intermittent
17880 - EVAP Leak Detection Pump: Short to Ground
P1472 - 35-10 - - - Intermittent
17843 - Secondary Air Pump Relay (J299): Short to Ground
P1435 - 35-10 - - - Intermittent
17938 - Camshaft Timing Adjustment: Short to Ground
P1530 - 35-10 - - - Intermittent
17829 - Secondary Air Injection Solenoid Valve (N112): Short to Ground
P1421 - 35-10 - - - Intermittent
17923 - Intake Manifold Valve (N156): Short to Ground
P1515 - 35-10 - - - Intermittent
17529 - Oxygen (Lambda) Sensor Heating Circuit: B2 S2: Short to Ground
P1121 - 35-10 - - - Intermittent
17525 - Oxygen (Lambda) Sensor Heating Circuit: B1 S2: Short to Ground
P1117 - 35-10 - - - Intermittent
16486 - Mass Air Flow Sensor (G70): Signal too Low
P0102 - 35-10 - - - Intermittent
Readiness: 0000 0000
Do these components share a common ground, or connector, I imagine it is a simple fix. just wiggle fuse, or ecu connector?
My mother-in-law has a Camry and she is pulling codes for running lean and airflow leak detected. The little red circled device mounted on the side of the air intake boot is hissing out air, yet I don't even know what the thing is called....
View 7 Replies2003 Camry LE, 4 cyl, 165k miles – Got all of the above codes. Obviously checked gas cap and no issues there. Checked both VSV underhood and had clicking. Checked VSV at canister under vehicle and no clicking. Used a Dremel oscillating tool with flat metal blade to cut off rusted Philips head screw. Removed VSV and checked by jumpering to battery. No clicking, but did draw a tiny arc. That told me it was “trying” to actuate. Sprayed PB Blaster into hose fittings of VSV and mowed the lawn. Came back to VSV and it now actuated – but very slowly and delayed. Sprayed electrical contact cleaner in hose fittings with the VSV jumpered and open. Activated VSV several times and sprayed contact cleaner through the hose fittings several times – both directions. VSV began to active quickly. Put VSV back on vehicle. SES light went out by itself after it ran the EVAP test.
View 3 RepliesI have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 RepliesOkay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
I've been battling this truck for over a month now and starting to go a little crazy, It's a 2001 f350 7.3L, with a "used" 7.3L engine from a 1997. Transferred all the necessary parts to make it happen. Keep getting the evil p1316 idm codes detected coming back upon start up. Anywhere between 5-30seconds after starting the left bank dies. I've gone threw and replaced the IDM with a reman unit. New valve cover gaskets (with new harness). even went the extra mile and put in a new power wire (for the driver side) running directly from the new valve cover into the IDM bypassing a connector above the left valve cover. All injectors are checking out around 3ohms. With glow plugs all around 1-2ohms. What's interesting about this is, I can disable any one of the injectors on the left bank (doesn't matter which one) and the engine runs great considering it's down on one cylinder. But when I hook up that last injector it will kill the whole left bank again.
View 13 Replies