I have a 2004 Venture where the power steering feels tight. Fluid level is good. No leaks (had it repaired a year ago where line was leaking, and now repaired).
Turning the wheel under most circumstances feels pretty normal. However, say, doing parking maneuvers SOMETIMES feels like I have non-power steering for maybe a quarter turn, and then it picks up again.
The steering on my Ex isn't working like it should. At times it feels loose when cruising then feels tight when straightening back out after a turn... the wander is really bad...
My PS fluid is also turning into a muddy brown goo every 5k... I changed the PS pump this summer with a supposedly good used one...
What should I be looking at/checking for?
Been reading about the various ways a fuel level sending unit can fail; think I have a first!
Purchased a new sending unit on eBay for less than $25; dealer wanted over $70!
Dropped the tank, pulled out the pump, and took a close look at the unit; at first, I thought I had play in the bushing as others have found.
However, looking closer, turns out one of the two springed 'tangs' that ride up and down on the potentiometer had broken off, and was not making contact with the board! No amount of fuel additive would have fixed this!
1 hour job to complete the job, and everything works as it should! Terrible pic, but the tangs are inside the black square, and the one farthest from the pivot point is broke....
I have a leak on my Lexus, the car raises up normal my suspension work good but I hear the air leaking and the ride feels like crap.
Is there anywhere where I can get a diagram for the air ride system to see where all the air hoses go through.
I went under the car and I have a rough area where it is but if I could get a diagram it would be easier for me to see the hose I'm talking about and if possible would need part numbers along with the list.
I picked up this 2004 Chevy Venture for my daughter and it has a power steering fluid leak coming out of the power steering cooler line that runs along the frame in front. I know that the procedure to replace this line calls for disconnecting the intermediate shaft of the steering and lowering the subframe to gain access to the line connections on the rack. My question is, is it possible to replace that line without lowering the subframe? I ordered the new line and it's on its way. I wanna do the job right.
View 3 Replies2010 camry LE
A family member did a tune up on the car and did not realize that the power steering reservoir had a HOT and COLD min/max lines. He filled up to the max line for HOT while the car was completely cold. He also filled up with Prestone Power Steering fluid with Stop Leak instead of ATF/DEXIII.
The car was driven a few times for maybe 50 miles in total before I found out about all this and I drained the fluid out to the appropriate levels. However the steering at low/parking speeds is still very tight (tighter than what I used to remember, at least).
Did he royally screw up the power steering system here? What can I do?
I bought an 04 F150 SCrew 5.4 3V a while back. The power steering fluid level keeps dropping. I have topped off the power steering reservoir at least 3 times in the last month and a half.
What's got me baffled is I can't find evidence of a leak anywhere. The hoses, the pump, or on the belt. I've crawled over & under it. I can't find anything anywhere.
OK, after some bearing issues I replaced the crankshaft with a reman. The engine is now in, but it is not turning over like I think it should. It just feels too tight, and cranks slow. It cranks smooth, nothing hitting. It is hard to turn with a wrench on the front bolt. I am wondering if I messed up on the torque on the rod bearings.
I torqued them according to the book. First to 29 to 33 ft lbs, then rotated an additional 90 to 120 degrees. I went with the lower of the numbers, 29 foot pounds then an additional 90 degrees. The mains I tightened to 30 ft. lbs. then an additional 90 degrees.
Are these the correct specs? I did smear a little grease on the main journals before installing, but did not do this for the rods as the book says. Is this maybe something to do with my issue?
I did not measure with plastiguage to see, I didn't realize I was out of the stuff and didn't want to drive 50 miles away to get some! I am also wondering if heating up the bearings on one rod journal might have warped the rod and is binding not allowing it to turn. I did notice when I put it back together it turned a little hard, but figured it would be ok once it started.
I have a 2006 RX 330 with 116,000 miles. I noticed that i had a leak and the power steering oil level was low. I went under the car and looks like the power steering hose is leaking. The dealer wants $352 for hose and $325 for labor. I called auto parts stores and they say its a dealer item only. Someone told me I could have a hose company rebuild it for a lot less.
View 5 RepliesI started to notice a slight whine when I turn the wheel. My fluid is at low but it's pretty dark and I'm not sure if it was ever changed or when. I have 100k miles. What fluid should I use?
View 10 RepliesPracticing parallel parking with my daughter today, the steering all of the sudden got VERY tight at low RPMs. Speed it up a little and it was fine. Shut it off for a minute and it was fine (but the problem would come back). This happened after about 15 parking attempts. Drove it home (about 30 miles) and it was fine. Tried some low speed maneuvers this evening - no issue. I know it has electric power steering so there is no belt or fluid to check.
View 3 RepliesI've got an 08 F150 and the steering has gotten tight when at low rpms or when not moving. The pump's whining and laboring. Fluid is clean and full.
View 3 RepliesSo our 2006 f150 fx4 has been having an issue with stiff steering... at times like it doesn't have power steering at all.
We recently had the lower ball joints on both sides replaced. Before that the upper control arm on the drivers side was also replaced.
There are days that it is better... other times not so much.
This has happened twice now. I went to turn a tight corner and the power steering just went out. A moment or so later, it came back. Any conjecture?
View 3 RepliesMy Wife has a 2006 Chevy Malibu Maxx Lt, we recently had a series of factory safety recalls performed. Now we have a message coming up saying "POWER STEERING" and the steering wheel is tight and kind of jerky. We didn't have this much trouble before we had the recalls done.
View 10 RepliesMy coolant level sensor is bad. How do I replace it? I understand that there is a retaining metal wire holding it on. How do I get that wire off?
View 2 RepliesI have a power steering fluid leak. I believe (it appears to be) it is coming from what is described in the manual as the "power steering cooling pipe". It looks like it is right up front just behind the radiator on the cross member, and perhaps may have rusted through. All of the pipe is intact except one small corroded area.
I looked at the procedure in the manual to replace this and it looks rather complicated.
I figured I would just cut the leaky section out, and replace it with double hose clamps and a piece of fuel line.
My main question is: Is this in the return circuit (low pressure) or the supply circuit...High pressure.
On my 2004 s-cab the steering is starting go 'notchy'?
I have considered, tight upper or lower ball joints, pump, rack or even a sticking rear diff, but not carried out any checks yet except oil level
I've got an 04 f250 4x4 crew cab. I just replaced the upper and lower ball joints on both sides and also the drag link. My alignment was off from the bad ball joints so I had it aligned after I did all of this. Now the steering is really weird. Its like something is to tight. I can barely keep the truck straight because every time I barely move the wheel I seem to be going one way or another and getting it straight is nearly impossible to the point I look like a drunk driver. I can turn the wheel to go around a curve and let go of it and it will stay that way until I turn it back. It won't return itself. I'm kind of lost.
View 3 Replies2004 Venture LT ... The newest problem I am having that I haven't resolved is that the fuel gauge is showing empty, low fuel light on, range on trip computer says (E). I repaired the wiring harness's on the left and right front due to ac leakage, and I also repaired the pass through behind the drivers seat. This seemed to resolve many of the problems I was having.
The thing I noticed is that before I repaired the pass through connector the gauge would work intermittently but now its totally dead. I find it unlikely that the sender and the connector would go out at the same time. Any wiring diagram of that connector, or at least which color the wires are for the sending unit and the resistance values I should get?
I have purchased LS 460, 2010 with 21000 miles on it. Dealer said he put new Kumho tires on it. But the power steering feels hard, and is not even as soft as my Honda Pilot 2009. I have made an appointment with Lexus dealership for this concern ( I had the vehicle checked by Lexus store before purchasing.) I have read good reviews about Michelin tires, am wondering perhaps I need better quality tires. Do not know what the dealer is going to recommend.
View 3 Replies