This is my uncles car and Im doing this for him. Its a 2003 Venture that he has had since new. It overheated but there is no water in the oil and there is water in the radiator so I'm thinking that the thermostat froze not allowing water to circulate. It runs rough, makes a bit of noise from the top end.
View 5 RepliesI have an 02 Venture WB Package with the 3400 engine. Within the last week is has started to run rough under load. This happens mainly when it is driving, but it does happen at idle when there is an incline or decline.
A little background of what happened. It has not wanted to start all of the time and i heard that it might be a dirty MAF. Well, the MAF is clean and still not wanted to start all or the time. During this time I noticed a plastic line going from the intake tube into the rear valve cover was loose, so I thought this was the problem. I have big hands and couldn't reach the rear vavle cover without rocking the engine forward. When I finally got the bolts out of the mounts that attache to the engine, the engine rocked back a little. I didn't think anything of this and ratchet strapped the engine forward so i could reach the valve cover.
I got the line back in and put the engine back where it is supposed to go and all was well. A few days after doing this my wife told me the van was running rough so i took it for a spin and she was correct. It is hard to describe the sound it makes, but it almost sounds like there is was too much stress on the engine when I have the gas peddle pressed. The van doesn't lose any power i don't think. The van sounds great if it is coasting.
It only does this when there is a load on the engine in drive or if it is idle or parked on an incline or decline. It goes into the shop on thursday the 30th, but I would rather not spend the cash if i can do it myself. I am totally lost with this one. I have a video of the sound when I am driving it, but the sound isn't too loud on the video.
i have a chevy venture and it was running just fine untill this morning it started to have a good amount of smoke coming from the exhaust and is running rough i took it to the autozone and had the codes checked since i let someone borrow my code reader but when i went there and had it done i got 5 codes out of it and they are....
p0300
p0301
p0463
p1106
p1189
What happened to it since it was running just fine all yesterday and before...
My 2001 Chevy Venture van is accelerating on it's own and is now overheating. The heater works, the AC works but the defrost doesn't. I can be at a dead stop, put it in drive and it starts going on it's own, even up a hill. It's also developed a 'knock' or 'jump' with it automatically shits gears. I simply cannot afford a new engine, we did that last year when it overheated and blew the gaskets.
View 2 RepliesI have a new thermostat and a new water pump. Why is my car still running hot?
View 4 RepliesI have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesThe Right DRL Not Working on my 2005 Venture. I checked the following, also note the turn signal works and the following are ok.
Bulb
Bulb Socket
Socket harness
All Fuses and relays
When I turn on the headlights the day-time bulb lights...
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
My 1997 f150 4.2L 2 wheel drive truck has been running rough only in the morning. In the last year I have changed the plugs, wires etc. As soon as I start the truck and attempt to drive, it is very hesitant, runs rough etc., but if I only give it a little gas and not push it - the truck will run fine. This will only last about 45 seconds and then it runs normal for the rest of the day. I do not have original FORD sparkplugs and someone told me that might be why. I spoke to a mechanic (did not work for Ford) and he told me it wouldn't make a difference.
View 10 RepliesI have a 2003 Ford Taurus. It has been running rough for awhile. It doesn't happen all the time, alas. I took it to my local repair guy. They first said, oh this happens when the AC is on. But I knew it happened otherwise.
The check engine light came on yesterday, blinking, but didn't stay on. And it was running rough. Check engine light came on, on a Sunday so I had to wait until Monday to bring the car in. They just called and said they can't find anything wrong, ran it on the computer, says it's running fine. I said, did you check the spark plugs, wires, etc? (I am good at googling, to be armed with some kind of info)
I am thinking they just put it on the computer. I suppose it has to be running bad to show anything (?) and even then, it's no guarantee. Anyway. It seems like I am "sentenced" to driving this car until it strands me, catches on fire (I read about that possibility and I have on occasion smelled something burning), or if luck has it, when it is running rough, and I bring it in while it's running rough, the computer finds the problem.
I have been puzzled to why my truck isn't running right. We were driving down the highway one day and*then all of the sudden it starts running really rough. I changed MAF sensor, plugs and plug wires, oil change, fuel filter and air filter. Still doing the same thing. What this could be? 2003 ford sport trac..
View 11 RepliesI have a 2003 MCV36R Camry SPortivo, Australian spec. Have owned it for 12 months. Have had power issues.
Replaced:
plugs
fuel filter
O2 sensors (engine)
MAF sensor
Throttle Position Sensor
Have checker EGR valve - all looks good
Have coded OBD II, no codes coming up
Current issues are:
Flat spots from 1000rpm to approx 3000 rpm (esp on gear change from 1st to second)
Once flat spot stop, it powers up enough to throw you back in your seat.
Also, rough running when sitting on constant speed, esp bad between 65-85 Km/h.
Have recently done a 800km trip. half way through, isolated the EGR valve. Running probs have improved greatly, but still lacks power.
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 RepliesI am having a problem with my 1997 f150 4.2 v6. The engine is running rough at idle and while driving. It's running so rough that it vibrates the entire cab of the truck. I found water in the oil when I was trying to fix the problem. I have since had the heads redone and replaced all of the gaskets thinking this was the reason for the rough idling and rough driving. It wasn't; doing this fixed the water in the oil but still I have the rough running engine at idle and driving.
I have replaced the EGR valve, plugs and wires, pcv valve, replaced the coil pack, fuel filter and air filter (everything has been replaced with ford recommended parts because I have read that the engine I have doesn't like after market parts). While driving the engine vibrates and sound as if it's going in a cycle in a rhythmic sort of way (like a washing machine goes in a cycle), best way I can explain it. I have come to the end of what I think it is?
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
I purchased a 1999 F-150 Lariat 4x4 automatic transmission about a year ago. When I did, the previous owner told me about an idle issue that he has occasionally. He said that the issue was with the IAC. He claimed that he had replaced it several times but "it was hard to get a good aftermarket IAC that actually works". He said he tried several, but it never fixed the issue. That sounds like he wasn't replacing the defective part to me, but I don't know. This is my first truck to ever purchase.
Fast forward a bit (about a year), and I have had intermittent issues with idle and running rough since I bought the truck. I don't drive the truck that often, but they are becoming more common, so I want to get things fixed now.
Issues:
1. When running at idle, especially in park, the idle seems to fluctuate and never stay consistent. The idle drops as soon as I put it into drive, and the truck jerks a bit when going into drive because the idle was too high in park. It has never died while at idle, however.
2. When driving, especially up a slight or moderate hill, the power seems low and the truck starts to ping and jerk. The only way I can avoid the jerking is to stomp on the accelerator and go into a lower gear. And even when doing that, I still can notice an ever so slight jerk.
3. This past week, it was rough for an entire 40 mile journey on the interstate. Slight ping the entire ride home. When I pulled into the driveway, it was jerking until I turned it off. I haven't tried to drive it sense.
Potential issues:
1. IAC - maybe the previous owner was right. Maybe I should replace it again, or clean it with some carb cleaner.
2. Cam Phasers - I saw some posts about this on the forum.
3. EGR valve - Also saw some posts about this.
4. Maybe even the transmission? It doesn't seem to have an issue going into or out of gear, though.
I Have a 2003 Honda Civic EX that is running rough and the windows stopped working and the temp gauge doesn't rise. Would this be do to a bad/failing alternator or something else?
View 7 Replies2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?
View 1 RepliesThese are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?
View 10 RepliesMy girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?