TrailBlazer :: Running Rough And SES Light On - Codes P0340 And P0300 Misfire Detected
Jan 7, 2015
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 Replies
Advertisement
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 Replies
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 Replies
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 Replies
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 Replies
I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 Replies
I have a 02 Trailblazer that on Monday it gave me a code of P0300 (Random misfire), then two days later P0301 (Number one misfire); (I replaced plugs, boots and cam sensor) ran fine for 1 day now its a P0758 code (Shift solenoid B Electrical).
View 1 Replies
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
View 11 Replies
So I just had both cats replaced and now the car is running very rough and trowing out mis-fire codes. What could cause this? Going to disconnect the battery to reset the computer to see if that might work.
View 8 Replies
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 Replies
My 07 3.3 SF is throwing P0154 and P0300 codes. Autozone said the P0154 is Bank 2 pre-cat O2 sensor. But exactly which one? The P0300 is random misfire. Could they be related?
View 7 Replies
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
View 2 Replies
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
View 5 Replies
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
View 2 Replies
I have a 2005 F-150 5.4L 2WD 90K miles. I started getting a misfire and hard jerk when going uphill. No codes for a few days but misfire got a little worse and more jerking at full throttle acceleration or level throttle up a hill got codes p0300 and p0171. I replaced the fuel filter cleaned MAF and changed plugs Motorcraft plugs (none of them broke during replacement). Miss got worse. Missing at idle and no power 3K rmp to get to 40. Only code pulled was p0171. Replaced upstream O2 sensors and COPs. Will barely idle now. Dies when put in gear. Full throttle barely moves forward a few feet just sputters. Checked vacuum lines cannot find anything. Only code I get is P0171. Fuel injectors next? Or shop?
View 3 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
Okay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
View 24 Replies
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
View 3 Replies
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 Replies
