Toyota - Sienna :: 2005 - Making Terrible Noise And Shudder?
Feb 3, 2016
Within the last few weeks my Sienna has begun making a terrible noise and shudder when I accelerate. It seems like it is worse on the front passenger side. When slowly accelerating from a stop it makes a hollow pitched metal scraping sound that increases frequency with speed (up to 25-30mph) and at higher speeds just the shudder, no sound. Initially this was intermittent but now it is an all the time thing.
The sound and shudder only happens when accelerating, regardless of speed. When you are at cruising speed on the highway there's no shudder as long as you are at constant speed and at any time if you take your foot off of the gas pedal the noise and shudder stop. Because of the link to acceleration I don't think its a wheel bearing.
View 4 Replies
Advertisement
I own a 2005 Sienna CE with about 100,100 miles. In the past couple of weeks, I noticed that when I go into reverse, the car makes a whistling noise. At first I thought it was when I press on the brakes but it appears to make the noise even when not braking. It does not do this all the time; only sometimes. It appears to do it more when reversing and going down a slope.
I tried googling this but couldn't find anything. Some people say the brakes which were all replaced a couple of months ago.
Not sure if it is related but the car also makes low chirping noise when driving about 40 miles per hour.
View 3 Replies
I have a '98 Sienna that's still running well (271k miles) but about a year ago it started acting strange, just a rare but minor irregularity in the normally smooth engine. A few months ago I changed the fuel and air filters, but that didn't affect it. So I tried changing the tank pick-up filter and confirming that the tank didn't contain any gunk. Again, no change. Since then the engine light has come on, but it still runs well enough for now. My fuel pressure is solid (manual specs, 50psi I think). I'm not sure if it's too rich or too lean, but I'm convinced it's fuel related unless someone has a better idea.
My suspects: fuel pressure regulator (in the fuel tank), clogged fuel injector(s).
Other potential clues: 270,000 miles on the original engine. No smoke (that I've noticed). After changing the filters my fuel pressure was perfectly solid at manual recommendations (50psi if i remember correctly). New battery, new fuel cap (factory cap; sometimes store-bought ones don't vent correctly). Sometimes the fluctuation goes away for a day or two, while other times it's hard to accelerate uphill at highway speeds. The issue is not clearly affected by temperature (same when 40° or 80°). It was much less noticeable when I drove to Montana this winter; they have a winter blend, which might have masked the problem (or the higher altitude). It's possible I just didn't notice it as that drive killed my steering pump and a CV boot, so my focus was on other problems at the time. I found today that can I make it shudder a little at highway speeds: letting up the pedal for a moment and gently giving it a little more gas causes a gentle shudder, and very rarely what sounds like a small muffled backfire.
View 8 Replies
I have a 2010 Sonata V6 that I bought new. It has a little less than 50K on it. I tried to start it today and it made a terrible noise then died seconds later. I popped the hood and then started it again and the engine was shaking violently in the engine compartment and making a terrible knocking noise. I had driven it 12 hours earlier and it ran fine. I called a tow truck and had it taken to the dealer but if I know my dealer, since it is Sunday they probably wont get to it until Tuesday. Also, this car has had the signature V6 valve cover leak that has been fixed 3 times. I noticed it was leaking again about a month ago and I have just been checking the oil and adding it as it needs it. I dont think the engine ran out of oil because I checked it before the tow truck came and it was between low and full.
View 2 Replies
I have a '05 Corolla with around 80,000 miles on it.I've noticed for the past few weeks that it makes a weird noise when I brake. It's what I would describe as a gurgling or almost groaning sound coming from under the hood. This only happens about every other day, and only when I've slowing pressing the brake to coast to a stop or slowing on a downward slope.
Took it to one mechanic who couldn't duplicate the sound and gave up.The brake pads are relatively new and the sound is definitely not coming from the tires.
View 3 Replies
Our 05 Corolla, 160,000 miles, has started making a grinding sound when we upshift into 3rd, unless we let the rpms fall to below 1000. My husband said the clutch needed adjusting, but the dealer said this clutch is not adjustable. The dealer found nothing wrong and could not get the car to make the noise while in the shop. (It did actually get better for a while but got worse again almost immediately after the visit to the dealer.)
Our other car (a Saturn) has over 250K miles on the original clutch, so I don't think it's our driving. What could be wrong, and is this something that needs to be addressed soon lest we damage something irreparably? Also, this car has, since purchase, been nearly impossible to shift on the coldest mornings. Really, sometimes it is all I can do to get the lever in reverse to back out of the drive in winter (in Kansas). Warming up works, but it seems to take an inordinate amount of time before shifting is"normal."
View 3 Replies
The larger (60) side of my 2005 Sienna's third row seat is stuck in the "up" position. That is: the seat back will fold down, but the seat will not release from the floor in order to fold down into the well at the back of the vehicle.
The pull tab on the back of the seat that releases it moves in and out too easily. I viewed the mechanism under the seat and it appears that the pull tab is linked to a cable which rotates an armature, which in turn pulls one cable for each leg of the seat to release it. It looks like the cable connected to the pull tab is properly rotating the armature, but the legs aren't releasing. I can't tell for sure but it seems like the armature is rotated into the "release" position but it hasn't released the legs. I've crawled under the seat and tried my best to rotate the armature with my hands and a pair of pliers to no avail.
I was thinking my next step would be to try to rotate the armature with a little gentle persuasion (e.g. a hammer and a screwdriver or piece of wood).
View 5 Replies
I have a Toyota Sienna 2005 LE minivan , when I push the brakes my steering vibrates. I checked the tire balancing at the tire store just to double check no issues with balancing he verified all looked fine on tires he mentioned it is possible the front brake rotor causing it. He said I may have to replace the rotor itself since there may not be enough room for resurfacing the rotor. My question is
is it true I cannot resurface the rotors? if I have to buy new ones is it advisable if I buy it from "Autozone or OReilly " store or does it have to be the original from Toyota ? Toyota's pricing are 4 times more than from these stores. I know safety is important so let me know which option is better.
View 19 Replies
2005 Toyota Sienna minivan. Neighbor brings it by my house for a headlamp bulb.Rt head lamp low beam is out. Access is easy with the hood open.Rt Headlamp lens housing has moisture inside, left does not.Bulb is not broken or shatterd, it is in one piece.Before we spend $76 for an HID bulb, I have questions on the HID system. Is it that simple..just a bulb..or is there electronic controls involved that could be the culprit?Did the moisture take out the bulb in the first place ? ( halogen bulbs explode when wet ) or cause a chort in the electronics ? I already told her we need to take out the lens body and find and seal the leak and dry it out but I'm curious about the HID system.Do I dare just put 12v to the bulb ( #D2R 35w ) to test it or is that a bad idea with HID ?....( my best Ford tech to ask is off today )
View 2 Replies
So I've got the exact same issue as the person who posted this: [URL] ....
Brake lights not working on Toyota Sienna 2005 XLE after emissions testing connected to the dataport. Went to the Toyota dealership this afternoon and it looks like a wiring issue. Also found out when the left blinker is engaged, it blows the 10A STOP fuse which then causes the ABS and VCS(?) lights to illuminate. What a mess....
Is the easiest way to fix this just to run a new wire to the affected area? The folks at the dealership seemed to suggest they were going to need to rip out all the interior to find the break in the circuit. Timing-wise, this problem starting happening right after I went to get emissions checked and they plugged a cable into the data port to pull emissions(?) and other data.
My hunch is that these two events are directly related but I don't have much knowledge of how things are wired up , what might have caused this problem.
View 1 Replies
I have a 2006 Toyota Sienna with approx 64K miles. Recently, I am hearing a squealing noise when the AC clutch engages (AC is working fine and blows very cold air). When AC is off for when the clutch is not engaged - no noise at all..... I have been getting alot of different answers as to what it could be and it is very confusing.... to me - it sounds like a clutch issue and I have seen videos on how to take apart and see if it is a bearing or bad clutch. I did pull the belt and checked the pulley - it turns freely and there is no bearing movement. How I can go about getting it repaired without replacing the entire compressor and other expensive parts.
View 13 Replies
My 2000 Toyota Sienna has been making some concerning noises. It makes a periodic grinding noise, the period is related to the wheel speed...i.e. the noise happens once each time the wheel goes around. I can hear it while I drive, and it's even louder when I roll down the windows. The weird thing is that the noise stops when I hit either the breaks or the gas. First mechanic says that the wheel bearings are shot, and the second says they're fine. There is no "jet engine taking off" noise that I am told is typical of shot bearings, but there is a wump-wump-wump noise at higher speeds.
View 1 Replies
Having been on a long road trip, I noticed that every time I switch off the engine, there is a grinding noise coming from the engine. Took the van in to Toyota for a regular service, they could not find anything wrong. I then took it to an alignment place having replaced all four tires. They heard the noise straight away and think it is a worn bearing in the cooling fan in the alternator. 2007 Toyota Sienna LE FWD... The car only has 22,956 miles on it.
View 4 Replies
Had my wheel bearings replaced 3 weeks ago from a mechanic I never went to, as mine was on vacation. 3 days later tire fell off while driving. So we took it to my regular mechanic and had all safety issues fixed. New brakes, rotor, hub. But noticed that a grinding noise appeared. Took it back to mechanic, and he said that it was due to the spindle being slightly bent. Thst it wasnt a safety concerns, but will cause rotor/ brakes to wear out quicker.
I'd like to trust my mechanic, as he has always done good work for me in the past. But am a little shaky over every noise. I'd he correct?How soon should I get it repaired? I just dropped over $600 to get the can drivable again. So if I can push it off until I can afford it that would be great! Otherwise, I might need a small loan to repair.
View 7 Replies
For about a year now, my trusty Sienna has been making this intermittent little squeak. It's not loud (it's not the belt!). It seems to be coming from the passenger side, toward the rear. It only happens when I am moving. It seems to happen when I am running the AC. It is a soft little chirpy-ish squeak, about 2 seconds in duration. It sounds for all the world like a vent opening up with a squeak. Driveability is in no way compromised.
View 6 Replies
I have a 2002 Toyota Sienna van. My garage failed to check the brake shoes as requested, so I gouged the back brake drums and had to have them replaced. Shortly afterwards, whenever I brake, in the last 2-3 seconds before I stop there is a thumping noise from the right rear wheel. It will thump a few times, maybe 2-5 times, perhaps one thump per wheel rotation. I don't feel any pulsing in the brake pedal, and except for the noise braking seems normal. Could this be due to the shoe adjustment being too loose, so the shoe has room to pulse inside the drum?
View 2 Replies
I have a 98 Toyota sienna and it has started making a thud noise and skipping a bit when accelerating or going up even a slight incline. I have been told everything from it needs new plugs/wires to a new transmission. Could these cause similar problems?
View 12 Replies
So I started a "quick" strut job on my mothers 98 Toyota Sienna last weekend, after many complaints about a rattling noise on the passenger side while driving on semi smooth roads. I got in and found that the CV boots were gone, and there wasn't much grease in the boots, all the ball joints were loose, and the wheel bearings were starting to grind. So since the car is at 225,000 I ordered the parts and took Friday off. I started the job, and also found out that the inner tie rod boot was completely full of ATF(This cars power steering fluid). There was a massive 2 day struggle with the CV axle being rusted in the motor mount bracket. But I finally got it all replaced and back together.
So all told I ended up replacing the following parts; Power Rack, Inner Tie Rods, Outer Tie Rod Ends, Rear Lower Passenger motor mount, Strut Mount, Lower Ball Joints, CV axles, Wheel Bearings, Lower Struts, Upper Strut Mount, Fuel Filter, Brake Pads, Brake Hardware, Oil Filter, and the Oil. I got it all back together and just finished the test drive ONLY FOR THE NOISE TO STILL BE THERE!!!!! What did I miss? What could it be? Is there something simple I could have done wrong to continued to have the rattling noise? Also the steering wheel is off 20 degrees to the left, I could handle that, but its not my car and my mother says it needs to be fixed... PS I am planning on taking it in for an alignment, but it does drive straight down the road as it is.
View 13 Replies
Okay, my wife has a '99 Toyota Sienna with over 200 k miles. Recently, it has began making a loud exhaust noise. I looked at the exhaust system and cannot see any obvious holes. Also, her check engine light has been on for a while. I checked it and it said misfire in cylinder 5 (can't remember the code). Changed plugs and all, still the light. It also idles very high. There's no rotten egg smell that I can tell, but she does say that it seems like it doesn't have a lot of power when accelerating.
View 4 Replies
I own a 1999 Toyota sienna that has 112,000 miles. For the past few months there has been a whirring noise that seems to be coming from the center engine compartment. It started quietly and now has increased in volume. It reminds me of a speedometer cable that is beginning to fail. I have taken it to my trusted mechanic for a diagnosis and he thought it was metal on metal noise from the transmission. I have owned cars for 40 plus years and have'nt heard of this type of tranny noise. What could be causing this? It makes this noise under power and when I release the accelerator the noise almost disappears. Also there is a clunking noise coming from the passenger front wheel after releasing the brake pedal when I come to a stop. I have replaced the strut,ball joint,and lower control arm bushing trying to remedy this. I cannot find anything else that is loose.
View 4 Replies
Thumping noise in rear passenger side. I removed pads and rotors, inspected and found nothing wrong. I decided to replace the new rotor with same and the thumping is still there, but only with the brakes being used. Nothing felt in the brake pedel and the the van stops fine. So why the thumping noise?
View 4 Replies
