Toyota - Corolla :: 2002 - Tighten Spark Plugs To Same Torque Specifications As Regular Plugs
Mar 13, 2016
I am changing my own spark plugs for the first time. I have a spark plug wrench, dielectric grease, anti-seize compound etc.
I have a Haynes manual for my 2002 Toyota Corolla. The book was written before Irridium plugs were used. Should I tighten the spark plugs to the same torque specifications as regular plugs? The book says 158 inch pounds. How do I know I have tightened them to the right amount?
How do I avoid cross threading the spark plugs? What happens if you cross thread the spark plugs (assuming the car seems to be running fine)? Would I need a new engine or expensive repair when it is time to replace the spark plugs again?
View 19 Replies
Advertisement
I don't have a torque wrench. I just have a spark plug wrench. I changed my own spark plugs. I don't like taking them out and putting them back in. I'm not sure if I got the torque right. What should I do?
View 1 Replies
I can't get a single spark plug to come out of my 2009 Corolla S. I'm using a 3/8 ratchet with a 3 inch extension and a GearWrench 9/16" x 6" Magnetic Swivel Spark Plug Socket (3938D). Which is exactly what others have suggested. It feels like the socket is just spinning around on top of the spark plug. I'm kind of at a loss for what to do now?
View 10 Replies
I have been burning up spark plugs in the left hand cylinder (when facing the engine from the front). I have burnt up two plugs in a month in that cylinder. I have low compression in that cylinder and my oil consumption is high as well (1QT every 300 miles). My question is, is the oil fouling plugs and the oil consumption connected or is there other things I should look into?
View 2 Replies
I'm trying to turn the crankshaft by hand to verify my timing belt alignment, but meeting some resistance. is this because I have the spark plugs in? do i have to take them out to turn the crank? also, that little groove in the belt guide doesn't seem to line up with anything or get held by the rib on the crankshaft. does that matter, or have i got it installed wrong?
View 1 Replies
I have a 2002 Ford Focus coming up on 150k... still drives fine, but when I went to change the plugs today, I found all four of them submerged in oil. What's going on?
View 3 Replies
This past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
View 5 Replies
OK, well i have an old toyota pick up, One of the spark plugs ( the third cylinder) has some oily residue on it, indicating a problem with the piston. How bad could this be? Is it worth it to try and have fixed? I also am rebuilding my carb right now, so i am wondering if i is even worth continuing if the engine is messed up.
View 6 Replies
My old 1996 Camry with 2200 cc 4 cylinder engine, frequently keeps losing power to the spark plugs. I have changed the fuel filter and the ignition coil. That did not work. I also noticed that the car was starting when I unplug and replug the primary wire plug to the ignition coil. So I have replaced the primary power plug with a six inch pigtail and a used plug purchased from a salvage yard. This is not working either. The Toyota dealer near my house want to replace the igniter and the Engine Control Module just to be sure that these are not the sources of problem. The dealer did not test these parts. So I refused to replace the parts without a proper test. I would like to test these parts. Is there a test available for the igniter and ECM that could be performed. I have access to a lot of tools. I need a schematic and/or test to test these components.
View 18 Replies
As far as I know, my Passat has never had any other spark plugs other than OEM. I could also swear that those OEM plugs always had 3 grounds. My gas mileage historically averages about 27MPG in a mixed city/highway environment.
Recently, my spark plugs were replaced and now my gas mileage has dropped to 24MPG. I had a similar problem once with my previous car (1998 Jetta GLI) and it was due to going from a three ground spark plug to a single ground plug. Putting in three ground spark plugs instantly restored the gas mileage to previous levels.
I've read repeatedly that the NKG PFR6Q is the OEM plug but it only has a single ground. I realize that my memory could be faulty, but this is driving me nuts.
Alas I can't be sure what was there before versus what's there now, but I know my previous mechanic was a stickler for OEM parts. Would switching from a multi-ground to a single-ground cause a 10%+ drop in mileage?
View 3 Replies
I recently replaced the spark plugs on my 2002 Camry SE V6 (Gen 5). Let me just say that it was INCREDIBLY DIFFICULT to reach the rear 3 plugs as they sit underneath the intake manifold, way to the rear of the engine compartment. To reach those, I had to unplug some wires reaching on top of the engine, then loosen the intake manifold.
Along the way I broke a tiny air valve that sits underneath intake manifold, and replaced it right away, before starting the car.
When everything was put back together, the car started wonderfully, only to notice the engine light come on. I had the codes checked at the dealer and they indicated a malfunctioning Catalytic Converter and A/F Sensor and some other emissions stuff. Later that day, the VCS/TRAC OFF light came on as well. The service guy at the dealer said those typically come on together with the Check Engine light, which sounds like something he pulled out of somewhere!
The car drives well, no hesitation, no weird behavior, but has no traction control, naturally. While loosening the manifold I had to use a little force to flex it out of place. My guess is that it I may have yanked something out place: may be a wire issue, or a sensor.
View 13 Replies
I am having a problem where my spark plugs keep going out. I changed all the plugs, wires and coil pack on my 2001 Windstar and within a few months my van was running on 4 or 5 cylinders instead of 6 and this isn't the first time it has happened.
View 14 Replies
I have a 2001 saturn sl 2 and I noticed some oil around all the spark plugs. The engine seems to be loosing oil a little bit as well, about a quart a week. Its not buring it or leaking that I noticed.
View 2 Replies
'03 Solara 4 cyl, 135K repl. Fuel pump, 45# press ok, NO scan tool code(s), turns over fine, no spark 2 plug. Started/ran fine before fuel pump change.
View 10 Replies
I was having some problems and one of my friends told me to post up here before I went and saw my mechanic. So my car isn't starting (its a 06 r32). Now I've gone through a whole list of things and what I have worked out is that it is the spark plugs not firing (none of them are) although they are all brand new and were working not too long ago.
Battery is fine and fuses look good no warning symbols on the dash so I'm at a bit of a loss as to what it could be. Relays? Coils?
View 5 Replies
I was thinking about change my spark plugs on friday so today I went to check the ones the car have open the hood took the engine cover out and the ones on the sides, I see 6 wires 4 going to the left side(air intake side) and 2 going to the right side (where the oil fil cap is) so I say think this should be the spark plugs wires. I take one of the left side wires out and is cover in oil so I keep taking the other out one by one and all of them have a lot of oil I can't even see the sparks plugs. All the wires have numbers on top 1 to 6. I say this have to be the wires cause I don't see any other place where the plugs can be located at. The car is a 99 v6 fwd...
View 7 Replies
I would like to have a look at the condition of the ignition plugs in my V8 Phaeton.
According to the service plan, it's already time to change them and it also seems that the car has lost some power when accelerating.
Is it even possible to change them with the 'usual' knowledge (knows how to change a tire and so on) or should I better go to a professional.
View 24 Replies
Had issues with TBI, rebuilt. Had some starting problems after truck sat for 1 day or more, but would start after a few tries. At one point when it was particularly stubborn, starter lead vibrated off. Once reconnected, truck started, ran fine, but had some electrical humming & radio interference. The starting issue continued with some low rpm stumbling, when driving check engine light would come on at cruising speeds and go off 7-8 seconds after letting off gas.
Had 1 day lest week when I drove a bit more then normal (150+) but ran fine other then engine light. Next day started, but ran horribly rough with violent back fires. At one point stalled and would not restart. It looked and acted like it was flooding itself out and poor spark. Less then a year I replaced cap, rotor and coil. Now I have done all new plugs and wires. Now it appears I have no spark. I had been in the dash messing with the blower motor relay 2 days prior to the stalling and not starting.
Does the ECM control spark? Cant it go bad slowly? And if I had to do alot of cranking of the engine to get it to start, would that have any thing to do with it going bad?
View 14 Replies
Bought my car three weeks ago. I was looking around under the hood and noticed that the color of the connector on the spark plugs is different. Two are grey and two are black, in alternating order. What's up with that?
View 5 Replies
I have a 2000 Jetta 2.8 VR6 (the 6-cyl) with 128k miles and I have oil on my spark plugs, only on one bank of the motor (the bank closest to the bumper, if that makes any difference). I am aware that it is most likely a leaking or worn out valve cover gasket, and I have a replacement and am prepared to replace it. What I need to know, and I can't find this exact part anywhere, is do I also need to replace the spark plug tube seals??? The gasket I ordered did not come with any tube seals, I can't find this part on any auto parts website at all, nor have I been able to locate anything useful on this, or any other, website. I know the 1.8 has plug tube seals, and they come with the gasket, but does the 2.8 also require tube seals? I imagine it would, but I just don't know.
View 2 Replies
I have a '63 Buick Wildcat that has been sitting for 17 years. It has 2 spark plugs stuck in the motor. I got the other 6 out with liquid wrench. The other 2 have been soaking in liquid wrench for 2 weeks and I have been using a 3/8 drive spark plug socket, but still unable to get them out. How to get them out?
View 9 Replies
