Toyota - Corolla :: 2000 - Turn And Hazard Signals Don't Blink
Jul 31, 2014
Car is 2000 Corolla with 58k miles. Today, I had my hazard signals on while parked when suddenly....they stopped blinking. The signal lights in the dash just stay on...they do not blink. I also verified that both front and rear lights also turns on...it just doesn't blink.
The corolla has a fuse box under the hood in the drivers side. Here is the schematic for the fusebox: [URL] .....
From what little I know about mechanics/electricity, can I just pull the wiper fuse and put it into the turn signal fuse while I wait for a new fuse? Do I need to disconnect the battery?
How to confirm this is the part I'm suppose to install: [URL] ....
View 5 Replies
Advertisement
I just bought a 98 passat sedan v6 four days ago. When I purchased it the turn signals and hazards were working. I was driving yesterday and they went out all of the sudden. Thought it was the fuse at first, changed it, still not working. I bought a turn signal flasher relay, but the repair manual doesn't tell me which one it is so I can change it.
View 2 Replies
I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 Replies
Recently my Infiniti G20's turn signals and hazard lights stopped working. I replaced the flasher relay and turn signal switch but it did not solve the problem. Here is the kicker or clue. The lights flash when locking or unlocking the car with the remote FOB.
View 7 Replies
I have had an ongoing issue with my 2010 Santa Fe Limited with the battery randomly being drawn down and would not start the vehicle.
I saw a post somewhere on the internet to remove the Negative connection on the fender and grind it down to the bare metal so that it has a good ground connection.
I have done that last week, but last night before turning in for the night i looked out the window and saw lights in my driveway. I went out to investigate and found that the Santa Fe's turn signal/hazard lights were all on front and back and not flashing.
I got in the vehicle and turned the lights on and off with no keys and they all went out.
I got the schematics for the Santa Fe and i believe it could be the Hazard relay that seems to be located inside the I/P Junction box or could be the Hazard Relay Control in the BCM.
View 1 Replies
As i kid i hated seeing people make there turn signals blink faster but know as i got older I like it, so on my 2011 camry and i want to make the turn signals blink faster. Not too fast but a little faster. I know I need a flasher but i can't find one for the Camry. I know I have to remove the instrument cluster.
View 14 Replies
2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 Replies
No B5 posts since the variant has been running well....'til today, when I noticed irregular turn signal operations. This is for a B5.5, 2002. Occasionally they'd work as they should, but much of the time they'd blink a few times then stay off.
Continues to happen after shutting down the engine and restarting (was wondering if that would reset anything). I recall some sort of relay problem with the turn signals. Does this sound like what's going on?
View 1 Replies
I have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 Replies
How to make the 2012 Camry SEV6 turn signals do the little 3 blink for changing lanes, llike the newer ones, or the corollas do... Is it impossible???
View 14 Replies
I have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 Replies
My 2007 F150's turn signals and hazard lights quit working. I checked the fuse and it was blown. Once I pulled the old fuse out the truck wouldn't start at all. What happened?
View 3 Replies
I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 Replies
I was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
View 9 Replies
Recently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
View 1 Replies
Checked bulbs and fuses: not blown.... Is there a recall?
View 3 Replies
I just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
View 2 Replies
So, the alternator in my 2000 Mitz Galant just went out and my dad and I changed it, now when I drive my car sometimes the brake and battery lights come on while I'm driving and come on and blink with my turn signals (both of them). It is an intermittent problem, and I took it to Advanced and they said everything looked fine. what's wrong with my car?
View 1 Replies
Rhe problem is that both sides blink fast the left one used to blink normally sometimes and fast again. All the light bulbs work and are not led. I found the problem on the right side : in the front the side light blinks but the drl doesn't blink with it. Now both sides blink fast. What part of the car i should check ?
View 3 Replies
My passenger side front signal light works properly, but when I turn my hazard lights on it will not blink normally (the other 3 blink). Inside my truck when looking at my dash I see the small green blinking arrow for the left signal, but not for the right when the hazards are on. When using the signal normally, I see the small blinking green arrow for the right signal though.
1997 F150 Supercab, 4.6L V8
View 3 Replies
A few days ago my speedometer stopped working. Then yesterday all of my gauges stopped working, as well as my turn signals. If this is a fuse issue then which fuse it is?
View 9 Replies
