Toyota - Corolla :: 2000 CE Pulling To One Side And Steering Shakes Slightly At 70mph
Aug 1, 2013
I have a 2000 Corolla CE with 48k miles that I bought 2 months ago. I took it in for an alignment and balance because it was pulling to one side and the steering shakes slightly at 70mph.
The before measurements was this:Left Front:Camber: 0.0Caster: 1.2Toe: 0.17
Right Front:Camber: -0.7Caster: 1.6Toe: 0.28
Front Total Toe: 0.45Steer Ahead: -0.06
Rear Left:Camber: -1.0Toe: 0.50
Rear Right:Camber -0.7Toe:-0.04
Rear Tota
View 13 Replies
Advertisement
I occasionally experience steering wheel vibration no matter what speed I'm traveling. It starts out as a small shake and eventually becomes nearly impossible to hold onto the steering wheel. On two separate occasions, the brakes have gone out.The car has passed PA state safety inspection and I have taken it to 3 different mechanics and no one can figure out what the problem is. I have had new tires and spark plugs installed, keep up with regular oil changes, etc.
2004 Toyota Corolla S, 4 cylinders, 1.81 l engine, 240,000 miles, manual transmission..
View 7 Replies
Car is a 2000 Corolla CE.
When going at the desired speed (say 40mph) and there is lots of coasting room, I just let go off the accelerator and the car basically coasts. The engine RPM drops from 1600-1800 down to 900-1000 and it actually can coast a long way. Sometimes, I need to go faster (if I'm initially started at a slower speed) and when I press the gas pedal slightly, the tachometer shows the engine rpm jumps from the coasting 900-1000 to 1600-1800.
Is the tachometer (add on by ScanGuage) reporting it correctly? Is this a bad form of acceleration for the engine?
View 8 Replies
Had my car checked prior to traveling, news brakes, drums, rotors, they also found ice under my car and in my wheels, the mechanic broke those off. I had no problems with the car prior to the mechanic giving me clearance for travel. When I arrived in Ohio, within a week of arrival my front end would shake at about 70mph, continuously. It is a significant shake. The whole front end (steering wheel, etc.). If I slow down to around 55 mph or 60 for around five to ten min. and then speed up it would stop for a while. If I am on the road for more than 30 min it will do it again. I attempted to replicate this weekend with no luck until I was on the road for 20 to 30 min. I felt it might be ice again so ran my car thru the car wash.
View 3 Replies
So what is the deal with this whole steering wheel vibrating over 70mph? I have new balanced tires and the alignment has been done already. The steering wheel has a very annoying mild shake over 70mph on the highway. When I went back to the tire shop I saw the guy rebalance all 4 tires correctly. They told me to look into getting all alignment done. The car has 123,000 miles and had the 2 front struts replaced at 83,000 miles.
View 6 Replies
Noticed the steering wheel shakes just slightly at highway speeds. Happens to me when I'm at around 65-70mph and above. It's just very slight, so I really wasn't thinking its an alignment issue at all. I didn't know if this was a bit normal for these B7s or what. I've had alignment issues in cars before and this just doesn't feel that bad, but its enough to give me pause.
View 7 Replies
I have a 2000 Corolla CE with 48k miles. When braking hard, the pedal vibrates and the brake performance was not that good. So I had the mechanic replace the front calipers (L&R), both brake pads on front, and rear drums.
After that, when braking, the pedal vibrates...but not that much. So I had the mechanic replace the front rotors (L&R). Now, when braking, the performance is good and it does not vibrate.
However, if I brake really hard...there is a little bit of pedal vibration AND shaking steering wheel. My car also needs an alignment since it pulls to the left (will get one on Friday).
Do you think the shaking steering wheel and the slight pedal vibration is due to the alignment or maybe the rear rotors need to be replaced? When traveling at 70mpg, sometimes the steering wheel slightly (very slightly) shakes....my guess this the tires need to be balance/alignment.
View 2 Replies
Ok everyone the good weather is back, so the drivers side window is down and, I am back to diagnosing an issue that I've been having for some time now. BTW were dealing with my DD 02 1.8t wagon. So all the time over any little bumps in the road or anything that i roll over that "shakes" the drivers side wheel I get this terrible rattle noise. I mean it sounds like I am a dump truck bombing down the road with a bunch of shovels in it......well not that extreme but that sort of shake noise. Anyway the noise however does not occur over any bumps when i even just slightly apply the brake. So I know that it has got to have something to do with the brake rotor or caliper or something on that wheel. Any common issues with brakes? I mean i doubt it is hurting the performance of the vehicle but it is extremely annoying and i feel like something isn't stable that should be until i apply my brakes.
View 11 Replies
2000 Corolla - "growling" noise on the passenger side of the engine / stops when I turn the steering wheel - no loss of PS fluid (I also flushed the system) - which bearing(s) might be bad...?
View 2 Replies
I have an 06 crew short bed 4x4 238k miles ... It just started out of nowhere pulling from side to side. I got home and as i made the turn onto my street I felt the whole front end shift as I was turning almost like a knot in the steering i popped my head under and saw a greasy gear box everything else looks ok.
View 14 Replies
I have a 2001 toyota corolla with a manual transmission that I just bought that has about 130,000 miles on it. It runs very well except for it runs out of oil about every 150 to 200 miles. The car does not seem to be leaking oil, however revving the engine in the slightest causes the car to smoke from the exhaust pipe. We tried changing the oil as well as putting in high mileage oil and sea foam motor treatment. This worked slightly but not much.
View 9 Replies
5 speed stick shift, first thing in the morning no problem, after driving a while it shakes in reverse and does not want to move, going forward is no problem, clutch and cv joints were replaced 4 years ago, 170k miles.
View 6 Replies
The car is a manual transmission 2005 Toyota Corolla with around 90,000 miles. I'm not the only owner. The car was bought used. It appears that the car was in a front end accident that doesn't appear in a carfax report. This can be identified by the poor clearcoat paint job on the hood flaking off and the absence of the air conditioner, as well as some rather pathetic body, work with noticeable bends and a few missing screws. Most of which I consider cosmetic and irrelivant to the car's operations.
The tires are bald and the car has had an alignment about 2 years ago after I replaced the struts. I wasn't notified of any bad ball joints, but that doesn't mean thats out of the question. The car has a bit of a shake at high speeds. Sometimes the shaking is violent enough to reduce speed. I noticed that more often the shake is really bad above 60 and quite scary above 70. This isn't always the case. Sometimes the shake isn't as noticable by comparison.
At low speeds the car seems to have a wobble or repeatative hop. The steering wheel has a rythmic pattern moving back and forth a few degrees. Enough to make holding a full cup or soda not a safe choice unless the desire is to wear the drink. The wobble appears to be a little worse when the car is cold. Winter mornings seem to bring out the worst in the wobble.
I would like to do as much work on my own as possible to save $, but I realize I may need professional service equipment to diagnose some of this. Can car tires be diagnosed for having bulges with some sort of test aside from visual inspection alone? Is there a tool that can be used to verify the metal of the wheel is true and not the source of the wobble? Do wobbles and shakes derive from bad tie rods and/or ball joints? What is the most common problem that produces symptoms similar to mine?
I enjoy the car's money saving potential, but it lacks an air conditioner which is vital for defrost operations and keeping the insane summer heat tolerable. If the repairs will cost me more than the car is worth I may choose to invest that money into a 2005 model as a replacement since I've grown tired of the lack of radio and no air conditioner. I'm trying to keep 5ish years behind the curve as not to waste money on the politics of new car value depreciation.
View 1 Replies
My steering wheel vibrates when I stop or when i turn on the AC...
View 8 Replies
I have a 2012 Toyota Corolla LE (automatic transmission) with 90000 miles on it.
For a long time now I have dealt with a whining sound in my 2012 Toyota corolla. The symptoms are that the sound only happens when the accelerator pedal is slightly engaged. This happens at any speed. At the slightest push of the pedal a whining/spinning sound happens and if you maintain pedal engagement the sound of whining/spinning continues. The sound goes away instantly when the pedal is depressed and will again come back when engaged subsequent times.
I have been researching on the internet and I seem to be pointed in the direction of the transmission fluid to change from the Toyota Genuine ATF WS currently being used in the 2012 Toyota Corolla as the stock transmission fluid to Redline D4 as others have experienced a similar noise problem in 2010 corolla models and have made the noise go away by using the Redline D4 because of viscosity differences. I am not sure however if the same transmission model (U341E) is being used in all Corolla models.
View 6 Replies
A couple days ago I saw that my Toyota Camry was overheating, the gauge was going about 3/4s of the way and then returning to normal. I had then replaced the T-stat but noticed the fans were not running, so I replaced the relay as it tested bad. The fans then started to work when the A/C was turned on, but I noticed the car was still going 3/4s of the way then returning to normal.
So, I took it to a mechanic and looked for his opinion on it, he tested it and said that everything is working fine and when the engine gets hot enough the fans kick on, bit the gauge still hits 3/4s hot and then returns to normal. My mechanic said that he has seen this before in other car models and that everything is working as intended. I was just wondering if this is a common occurrence with some cars? Or should I look for other possible problems? I've never personally owned a car that looked like it was overheating then quickly corrected itself.
View 9 Replies
I just bought a 2010 Corolla S a few days ago and noticed today that the driver side mirror shakes while driving. I think the mirror might be a little loose. Is there a way to tighten the mirror without damaging the housing?
View 3 Replies
I own a 2015 LX570 with just 8000 miles on it. Been having an issue with my steering position. Every time im on a straight road the car seems to be pulling to the left side if my steering wheel is placed exactly to the center. At first i thought it was an alignment issue as i took it several times to the dealer and they just tell me that there is nothing wrong with it and it drives accurately straight until one time a guy from the dealer came and checked it himself with me and realized the issue and told me that its not an alignment issue its something related to the the electrical steering position not being accurate (( that's what he said)). They took it in and made it accurate as they say, to be honest its not really accurate but much better than before until last week when it became worse and like how it was before, pulling hard to the left, its like if i want to drive straight i need to pull the steering wheel slightly to the right.
View 1 Replies
My accent just crossed 180K mark. From last year the steering wheel shakes quite a bit at highway speeds ,say 70MPH. It's especially bad when I accelerates . Took the car to a shop, they told me two things, the CV axle of passenger side needs replacement, and the wheel hub bearings are bad(both front wheels). They quoted me $200 for replacing the cv axle, and $400 for replacing both front wheel bearings. Since I don't even think the car worth $600 right now(given high mileage), I told them I'll just do the axle(I know how to do it myself but don't have the time, plus it won't be that much cheaper DIY anyway). They said fine, but if you don't replace the bearings you may have the wheel fly off one day and that's dangerous.
They replaced the axle, and the car drives a lot better now. There's still a little bit of shaking at high speed but 75% of that shake has gone away. My question is, does the worn out bearing causes car to tremble at high speed? I heard other people told me there should be a grinding or loud hawling sound if the bearings are bad, but I don't hear that. I searched the internet and some people say, to determine if the hub bearings are bad, just drive it for 10 minutes then feel the hub. If it's barely warm, the bearings are good. If it's warm to hot, then the bearings are bad. I felt it and it's warm, but not too hot to touch. I tried the rear wheels and those are barely warm indeed.
So from this method it seems the front wheel hub bearings are indeed bad. I wonder how long I can keep driving this without endanger myself. $400 is not cheap for this car and I don't have a machine to press in the bearings myself. I can disassemble the rotor and hub that's not a big deal, but I don't know how to get the old bearing out and the new bearing in. Is there a machine shop that just do the pressing? Or, is there any shop selling the hub assembly with bearing already in place? this way I just remove the old hub assembly and replace it with the new assembly, a lot easier. I searched the internet but can only find pre-assembled hub w/ bearing for the rear wheel of this car. I need the front ones.
View 4 Replies
My old car has this problem when it's on highway the steering wheel shakes quite a bit. Is it a wheel alignment problem or wheel balancing problem? Since I've just fixed the transmission I am driving this car more often(to save gas) and this problem is really annoying.
View 4 Replies
I just bought this transmission from a reliable parts dealer. Should have about 50k miles on it. Looked really clean when I got it.
The guys who put in the tranny cracked a speed sensor, so I bought a new one and put that in. I dried off the sensors and screwed them into their spot on the tranny after removing the intake filter that was in the way.
Even with the new speed sensor the car is still doing the following:
1) Does not go into reverse until I've gone into drive for a couple seconds, pulling forward. Reverse does not work. However, when I unplug the speed sensor reverse works right away, but we still experience the following...
2) car goes from first to second gear to third gear smoothly, as it should. Seems really smooth like a car should shift! However... it won't go past 3rd gear and then it won't downshift! So, even after stopping and idling, I can't leave 3rd gear.
3) When I turn the car off, then turn it right back on, I can go through first, second, third gear again then... it stays in 3rd gear.
Another issue that has come to my attention since I got the car back, is the steering wheel shakes pretty hard while idling with no gas. While driving it seems smooth -- idling again it shakes heavily. what could they have damaged while putting in the tranny to cause this shaking?
So far as the funny tranny stuck in 3rd gear, it seems to me like it's a computer issue? But, what could be the cause? What tests can I do to determine the cause of this problem besides the ones I've run so far?
View 17 Replies
