I just had an OBD code pulled on my 2010 Camry and it turns out that my Heated O2 sensor for Bank 1 Sensor 2 is failing. I'd rather do this myself if I can but I can't figure out where this thing is. This is something I can access myself and swap out? Or does this need to be fixed by a mechanic?
View 4 RepliesMy cousin's B5 wagon automatic 1.8T ('00) was shaking and vibrating intermittently. I took it down to Autozone and borrowed an OBD2 scanner. This is what it said (only one code, and the CL was off, although it comes on intermittently):
P0741 - Torque Converter Performance or Stuck Off
I threw a code and I have it but I am unsure what to do.
The code is P0353
"Ignition Coil C Primary/Secondary Circuit"
I saw that this might be the coil, the wiring or the ground? I had my coils go on my 1.8t Jetta and that was pretty distinct as the car ran like crap.
The car seems to run fine, I have had the code for 2 days. It went off this morning and it came on again this afternoon.
My daughters 2000 explorer has a PO172 code, tune it up,Replaced filters plugs & wires and rear O2 sensors that were damaged. Has 65 psi on fuel rail. Can not find any vacuum leaks. Not sure maybe injectors are dirty.
Also I replaced MAF, now it idles, But it's a rough Idle,Gets worse in gear. She say's on cold start up she can smell a whiff of gas ..
I have a 2005 Jetta 2.0 BEV GLS. I got a code P0302 for misfire on cylinder 2. I am pretty sure it's the Ignition coil. I live in Canada and my autoparts store only has BWD brand. I have read this is a crappy brand.
View 1 RepliesI have a 2006 prius whose check engine light just came on 1 hour ago. I had it diagnosed and it is giving me the p1121 code, or the coolant flow control valve. I checked the coolant level and it was very low. I added fluid, but the CEL is still on. I have to make an 11 hour trip tomorrow.
View 19 RepliesI took my 2006 in for its 50,000 mile oil change today, and I was told I had the following codes related to the transmission and the park/neutral switch:
P0852 (System: Hybrid Control; shown as "hist," presumably historical)
C2315 (System: Transmission Control; shown as "curr," presumably current)
My car is running fine, and none of the dashboard lights have indicated any problem.
So I bought a used 2005 Prius back in August it had 88,000 miles on it and was out of warranty. But I had a full inspection on it and the car was in great shape. Well, after a few months of driving, I got the P0420 error. I took it into my mechanic who cleared the code and told me to call him if it came back on. It came back on, then I cleared it myself, and it came back on again. So it was confirmed that I had a bad catalytic converter.
[URL].......................
At the end of my first week of ownership, I encountered problems with the rear cabin light in my car not working properly - sometimes it came on when the doors were opened, and sometimes it did not. I mentioned it to the Phaeton technician at my dealership, and we agreed to just defer investigation and rectification until the car was due to come in for its first oil change.
After I finished putting the start button in, I ran a diagnostic scan on the car, and the problem with the rear cabin dome light was the only remaining fault code. So - I kind of figured "gee, this can't be rocket science to fix", and I removed the rear cabin light assembly from the roof of the car.
I had a close look at it, and found the cause of the problem pretty quickly. When the assembly was put together, the tiny black wire that carries power to the rear cabin interior light button became trapped between the large bus bar that serves as a ground for all the switches and some foam insulation that protects the circuit board from the ground bus bar. The entire assembly would have tested out just fine when it was manufactured, but over time, the vibration encountered in transporting the car from Germany to Canada, and the vibration caused when I drove the car around during my first week of ownership caused the bus bar to cut through the insulation on the wire - hence the short circuit. All I had to do to fix it was just poke the wire out from under the bus bar. Everything works great now.
The fault code that was generated - "Rear Interior Lamp Button - Short to Earth" was absolutely dead-on, and took me directly to the problem. I really doubt if I ever would have found this problem if the car did not have such a competent self-diagnostic system.
is my Toyota camry going to stall cause it has po401 code and I think it has an muffler or exaust leak can the cause po401 code.
View 3 Replies2002 Camry, i was gonna remove manifold & 1st step was to pull relay to relieve fuel pressure(which it did) but then i needed to use car so i put it back now car turns over & immediately sputters-out unless i depress & hold accelerator. Also, fuel in tank is very low, in case that could be culpable.
View 3 RepliesI got two new Bridgestone ER300 Ecopia to replace two on the front. Trouble is after getting the tires fitted the car pulled to the left quite badly and my mpg's went down! Hmmm. I checked the tires in case a non low rolling resistance tire had been fitted by mistake, but they were correct. I then checked the pressures, which again were correct. So I guessed the tracking must have been out so booked it in with the dealers for checking. After a couple hours and a couple test drives later they advised the tracking is fine and the tires are fine. Odd.
Just filled up for the second time since the new tires and I'm struggling to get anywhere near 50 mpg! Even after a few long trips where I know from past experience that I could get mid 60's easily. I've inspected the tires closely and note that one of the new ones is made in Italy and the rest are from France. All the loadings, ratings and the type are the same, just made in a different factory and it is a slightly lighter colour compared to the French ones.
I have an automatic 6 cup and get a P1780 error code. Says to check neutral shift sensor, which I replaced. Code came back. Internet search says to try wire loom in trunk, driver side. Opens 2-3' of it and found no frayed or broken wires. All lights work fine. Car shifts fine. No other issues other than check engine light and that code. Where else to check?
View 3 Replies2006 Toyota Camry 4 Cyl Manual Transmission. I'm getting a PO017 code - Engine Coolant Temperature (ECT) Circuit Low Input.
The dashboard temp gauge reaches a red H at low speeds. After about 15 minutes of driving, the car overheats and shuts down when the car slows down. I wasn't at home and didn't have coolant, so I put water in the coolant reservoir. 15 minutes later at home, the car overheated and shut down. The water in the reservoir was boiling and steaming.
When the car is idle, the radiator fan turns on immediately. I noticed the passenger side fan doesn't run. Could the one fan be the problem?
I was also really low on oil and added oil. There's oil on the engine block too. I might have multiple problems at the same time. See pics. [URL] .....
I have a 2011 toyota camry. 3.5L v6. I have code p0157. I know my car has 4 o2 sensors, but I am not sure which one to buy. Where this o2 sensor is located, and which one to purchase. A part number would be very useful.
View 3 RepliesI have a P0171 code (lean bank 1 sensor 1) on my 2002 toyota camry 4 cylinder. I don't have any other codes except for an unrelated P1780 neutral safety switch code. It has had both codes for over a year.
I have replaced the fuel filter, the upstream o2 sensor, and the PCV valve. I also cleaned the MAF sensor. The mechanic performed a smoke test and found no vacuum leaks. Did a fuel pressure test and it's normal. Mechanic thought it would be fuel pressure because the car starts a bit slow when cold, but nope. The car runs great and still gets great gas mileage. I've never experienced a misfire in my 12 years of owning the car. I am asking because I am at a loss as to what it could be.
2001 Camry 4 cylinder. Check engine light came on yesterday. Advance Auto pulled out the code P0446 for the evap. emissions system vent circuit.
The car has no symptoms other than this and is current on all maintenance, but obviously it is a 10-year old car and so it goes.
This past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
I need to know the Fire order for the 2011 toyota camry se 2.5 L engine. so I can find which oxygen sensor I need to change. I m getting a P0137 code and it said is the bank 1 sensor 2. I think that is the one after the catalytic converter but need to find out for sure.
View 1 RepliesThe computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 Replies1996 Toyota camry le 4 cylinders has code po401 does it damage engine what will it do. Insufficient exhaust flow...
View 3 Replies