Toyota :: 1994 - Overheating And Rough Idle
Jan 12, 2013
My 94 Toyota Pickup is having a strange intermittent issue. Engine will run hot, like the thermostat is stuck periodically. Does not overheat, just runs much closer to the red than usual. Again this only happens sometimes. It is worth noting that it is winter here in Northern Sonoma County, CA, so it may actually get into the red if I were driving around in the summer. I have also not taken it on trips over 30 miles when it was doing this.
When this problem occurs (e.g. the engine has been running hot) and I shut the truck off and say run into the store, then come back to a heat soaked engine it idles very rough when started (like it's missing on one cylinder). Once I put it in gear and start driving the idle smooths out and I have no problems. Problem has been going on for about a week.
Sticking thermostat seems obvious but that does not explain the rough idle on start up. Or does it. If so why?
View 11 Replies
Advertisement
The car: 1994 toyota celica GT 2.2L automatic
Here's the problem: car starts fine when cold. When fully warmed up, if i stop to go to the store or something, and then start it after like 20 - 30 minutes it will start and the idle will be fluctuating between 800 and 400 for a few minutes and then even out. sometimes it will actually start up and die immediately, in which case i can save it by giving it gas for a few seconds and then it's fine.
What I've done so far: plugs (NGK), wires, cap, rotor, fuel filter (toyota), (checked air filter. still clean), tried cleaning the throttle body and IAC with some deep creep spray while on the car (not much effect).
View 14 Replies
I have a 220k 1994 Corolla with I have come across a couple problems recently. It all started about a week ago when I decided to change my rear brake shoes. The old ones turned out to be all cracked and everything but were generally in pretty good shape in terms of wear. Anyways I put the new shoes in (my first brake job) and tightened up the e brake cable and went for a test drive. I walked away extremely satisfied, the e brake worked perfect which was my main reason for changing the shoes in the first place.
Basically the whole thing worked perfectly until 2 days later. I was driving for about 8 miles when my brake pedal suddenly fell through to the floor (or pretty close) at first I even thought I hit the clutch pedal! anyways after pumping the pedal a few times my pedal feel returned about 70% and after another maybe 10 seconds braking power was lost again until I pumped the pedal. So lucky for me my destination was a 1/4 mile away so I parked and checked the fluid level; it was at the max mark, then I check the wheels/drums and they were REALLY hot.
Also the driver's side drum had a faint smell of brake fluid. Anyways about an hour later I went for a short drive and the brakes worked fine so an hour after that I drove the 8 miles home and about 1/8 of a mile from home same thing happened; brake pedal basically goes almost down to the floor until pumped. My thoughts were that the new shoes were constantly rubbing and the old fluid overheated and caused failure so I flushed the system and put new fluid in and adjusted the shoes "in" with the click adjuster bolt. I had a really hard time getting the drums of to begin with. That and I loosened the e brake cable just in case.
So the next morning I drive about 5 miles without using the brakes pulled over to check that the drums were not heating up anymore (they weren't) so I thought I had fixed it. Well 3 days later (last night) I was experiencing the rear brake stickiness again. Basically when I was just moving from a stop where I had used the e brake to secure the car, I could literally feel that the rear brakes were stopping the car pretty aggressively and sure enough after a few more miles my brake pedal fell through so I poured water on the drums and they started to let off lots of steam, even after like 10 bottles!
So I limped to my friends house at 12:00 AM and jacked my car for a look. Again the drums really didn't want to come off and once we did get them off my friends dad inspected them and could find anything wrong with my installation. The conclusion that we came to was that the auto adjustor for the shoes makes the shoes too tight and they rub. So I am thinking maybe this is cause for the fluid to overheat and boil, causing the pedal to fall through. The pedal fell has gotten much worse since I bled the system 3 days ago so that may be an indicator. Did a test this morning for 5 miles and the drums were just below lukewarm.
View 1 Replies
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 Replies
I have a 1994 Volvo 940 and have previously owned a 740 for many years. I've only owned this car for about 1 month. The car appears to have been well cared for. Doesn't leak a drop of any fluids, everything works, and mostly a really nice old car. What happens is that it idles rough when it's cold. In fact, I have to pump the gas pedal to keep it going. When I first start off, the performance is less than what it should be too. Once it get warm, it mostly runs fine.
I have so far replaced, the Plugs, Wires, Cap & Rotor. All the vacuum lines, crank position sensor, Air Mass Meter and the fuel filter and most all the fuel lines too. The Fuel Pump Relay was replaced but I removed it and saw a few cold solders and fixed those but no changes in performance. Before I replaced the Air Mass Meter I brought it to local shop and they returned a readout of 2-3-2 which I'm understanding means running too lean. That's why I replaced the Air Mass Meter. (I did notice a big improvement once I replaced the Air Mass Meter too.) It was interesting that when I replaced the Distributor Cap, I noticed like black carbon in there and I'm not sure what could cause that. Although, I did find the previous plugs were not all the same. Three of them were high spark performance plugs and one was just normal
I pulled the Idle Air Control Valve and plugged one side to ground and the other side to 12V and noticed the flapper moving when powered on/off. The previous owner told me he replaced both fuel pumps about two years ago. It also looks like the fuel regulator valve is mostly new.
I'm guessing now that I have a problem with the Idle Air Control Valve or perhaps the Fuel Temp Sensor under the intake manifold. I purchased the Fuel Temp Sensor and just have not installed it yet. I really don't want to remove the intake manifold but I know it's not going to be that bad. I know that it could be carbon build up on the intake valves but I'm not quite convinced yet. I put some fuel cleaner in the tank to see if that works and so far nothing yet. The car only has 150K on it and I was told that during the owner before me did do highway driving.
When it's warm, the car does run very very well. The idle is still a bit quirky even when warm. For instance, when I power on the A/C, the idle RPM doesn't increase like I expect that it should. (It did on my 740) ... I'm still thinking maybe it's the Idle Air Control Valve too. Perhaps it's intermittent or do I understand that they can gradually open and gradually close?
View 9 Replies
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 Replies
1994 Toyota pickup... Engine misses intermittently both at idle and throughout rpm range. Cap and rotor clean,plugs read nice light brown fuel burn color- would injector cleaner in gas work.....
View 3 Replies
1994 Buick LeSabre Custom 3.8 Litre V6 with 103277 miles.
It runs smooth when idling in Park, rough when I put it in gear when I am stopped (either drive or reverse) has hesitation when accelerating, it smooths out again when driving then it starts to drive rough at about 55 MPH.
Mechanic told me it was the plug wires. I replaced those and the plugs. This fixed the hesitation when accelerating issue, but the other issues remain (now even seem a little worse) I thought the plugs and/or wires were bad, so I rechecked the gauge on the plugs and traced to make sure I had the wires hooked up right. Everything seems in order.
I have added fuel injector cleaner, and changed the oil, oil filter, spark plugs, spark plug wires, air filter, flushed the radiator, and changed the thermostat. (For a tune up since it has admittedly been a while)....
View 1 Replies
I have a 1994 chev Blazer S 10. that has thesy troubles. when it warms up it runs high and hot exhaust and ruff idle. with a hot cat. Replaced EGR carbon build up at times.replaced fuel pump, and all the senors under the hood. Still runs the same.
View 3 Replies
94 Ford Ranger 2.3L
I started to have a slightly rough idle a while back, but not severe. I figured she was just aging a bit.
Changed plugs. Check engine light came on. Changed plug wires. Then I had a couple of episodes where it started to lose power and idle really rough (stalling). Both times it stopped after a few minutes. Had code read- they said it was coils. Replaced ignition coils. Check engine light still on, but it went a few weeks without power loss.
Tonight the loss of power returned and didn't leave, and I had a glowing red catalytic converter after I limped home 20 miles (hope I didn't do any serious damage, I was stranded.)
Found this post : [URL] .... But there's no resolution.
So, I'm probably dealing with a misfire, and I'm sure I torched my cat after tonight. So any other easy diagnose/fixes for a misfire? I'm a shade tree mechanic- so I know just enough to get myself in trouble. If I can't get a resolution soon it will be off to the mechanic (which, maybe I should have done 1st...)
View 2 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
I have a 94 Ford Ranger 4x4 4.0 V6. It has developed a rough idle and has lost i fair amount of power. I cleaned the maf sensor and iac valve. Along with replacing an o2 sensor that was reading bad, with no improvement. The guys at O'reilly took a look and think I may be dealing with a timing issue or a warped valve. My question here is to found the culprit? I'm very inexperienced at working on vehicles and am damn intimidated by the scale of a project like timing. I should add that while traveling on the highway in high gear at low rpms, it develops a rough stutter. I can either power through it or ease off to get it to stop, but it resumes shortly after. It almost acts like an egr valve stuck open when on the highway. But that doesn't account for the rough (a consistent put, put, put...) idle.
View 4 Replies
I have a 1991 V6 automatic Toyota pickup. The transmission has ~230,000 miles, but the engine has been rebuilt and probably has less than 5,000 miles on it. I am having overheating issues in both departments.
Engine overheating: This has started fairly recently. My truck began overheating at idle (usually at longer traffic lights) and would cool down again once I began driving. My coolant was low, I took it to a shop, and they fixed a small leak. Fast forward a few weeks and it happened again, and this time when I turned on my heat full blast to take heat off the engine it blew cool air until I started driving. Took it back, they found no more leaks, and couldn't duplicate the overheating symptoms. They also said the fan and thermostat seemed to be working fine. It seems to happen sporadically, regardless of coolant levels.
Transmission overheating: Firstly, my truck tends to delay/hard shift when I first start it in the morning. Once the engine warms up it goes away for the most part. I took it on a 100 mile trip camping on a fairly curvy/hilly forest highway and the A/T Oil Temp light came on. This has happened before when I took it on forest roads, even after a recent ATF flush. Needless to say I had to stop a few times to cool it off. It felt like the transmission was working too hard at a flat 60MPH (2,500-2,800RPMs). A couple times the RPMs were pulsing like it was switching gears back and forth. The next day driving in town everything was back to working order.
I'm not sure if these two things are connected... but they never happen at the same time. I'm taking it to a transmission shop but I want to make sure they don't try to rip me off unless absolutely necessary.
View 3 Replies
At idle, on hot days (90+) after about a minute, the A/C cuts out and the temp gauge begins to rise. Gets about 3/4 of the way to the red zone, but never reaches it. I changed radiator cap, but still does it. Fluid level is fine; no coolant leaks that I can see. Called a mechanic and asked about a radiator flush. He said he'd do one, but it probably wouldn't work and I should just bring it in for a diagnostic.
View 7 Replies
I just bought a 92 Toyota Celica for something to play around with. It's got just over 200,000 miles and everything seems to run alright except there is a really rough vibration at idle. The vibration is so bad that it's almost visible. You can still feel the vibration in drive but it isn't nearly as bad.
Any clue at what could be causing the vibration? I'll try to get a sound clip or video uploaded ....
View 5 Replies
I just imported an Toyota Belta (Yaris) 2009. When starting it after it's been siting for a while (i.e. over night) it almost always doesn't start on the first attempt, but will on the second, recording attached.
Also, it has a rough idle. Today it idled down so low when we were at a stoplight it sounded like it was going to stall.
We've changed the fuel filter, spark plugs, and cleaned the injectors and throttle body. The mechanic has run diagnostics which didn't indicate anything other than rough idle.
View 2 Replies
I have a 2000 Corolla with about 147,000 miles. At idle it runs very rough, but can accelerate up to about 50 mph. Then it starts to cough and wheeze and run roughly again and won't accelerate any further. It feels like the engine will shake itself off its mounts, so I slow down and stay under 50 mph. I replaced spark plugs and a repair place hooked it up to a computer. They then told me it needed about 1800 dollars worth of repairs to replace the valve cam I think they said. I'm skeptical and wonder if it just needs a tune up, . It has not had one since I bought it at 128,000 miles, and II don't know how long it had been prior to that.
View 5 Replies
My 2001 toyota camry is great but has an intermittent, annoying problem no one can diagnose or correct. If I drive for a while at top highway speed (say 65mph) and then have to come to a stop (to pay toll or stop light) I get a very rough idle and then the car stalls. Have had new plugs, wires, coil, radiator already done to solve problem. Check engine light never comes on. Can also drive lengthy trip and it doesn't happen.
View 18 Replies
Basically when the car is in D and when i am stopped with the brakes pressed on at a stop sign or a red light, the car starts vibrating and i can see the the rpm going down and then receiving back up and going down again something when the car is in R. its a 2009 toyota corolla le 90k miles. when the headlights are on, the rpm stays high so the car does not vibrate or anything. other than this the car runs perfectly fine.
View 1 Replies
I have a 2008 Toyota Camry SE with the 2.4 engine and auto trans. If I'm stopped and in drive the engine feels as if it's going to stall, the entire car "shutters". The tach reads between 700 & 800 but if I place the gear selector into either neutral or park it becomes "glass" smooth, I even have to look at the tach to see if the engine is still running! In neutral or park the tach still reads 700-800 rpm and the A/C is always switched off.
I've had it to 2 different Toyota dealers and yesterday to my regular mechanic. 1st dealer said to disconnect the battery and bring everything back to default positions...no difference, battery was off for 35 minutes. 2nd dealer said to have the throttle body cleaned, which I did...no difference. A bit of background with the vehicle, I've had it since new, I drive 170 hiway miles per day, I use Shell branded fuel, oilchanges always at 5,000 miles, dealer serviced since new.
So yesterday my mechanic checked everything, engine mounts (OK), any error codes (none) cylinder compression (all within spec) spark plugs (OK except for 1 so I asked him to change them all), he installed 4 NGK iridium plugs and guess what...it still shutters & vibrates!!
View 3 Replies
2002 Toyota Camry
2.4 V4
My car has developed a rough idle when stopped and when accelerating. When I got the CEL, I had the codes read at Advance Auto.
The codes are P0301, P0302, P0303, P1349.
View 1 Replies
