I'm experiencing a serious problem with the tranny on my V10 TDI: When the engine's warmed up it sometimes starts slipping and generally keeps on slipping, even when cruising on the highway, until the engine is cooled off again. In thread [URL] .... I read something about a "faulty solenoid valve inside the tranny". Could this be the cause?
View 12 RepliesTook car in for normal service (69,000 miles) and had Tranny Fluid Service completed. When I took the car home I noticed some slight tranny slipping while accelerating up to highway speeds (so assuming 4th to 5th gear, maybe 5th to 6th). Took it back to the dealer and after a week it had a new transmission. Took it home and it slipped again, also only accelerating to highway speeds. Took it back and they told me they reset the computer that monitors my driving patterns. OK, not exactly sure what that means. So, now driving to work this morning it slipped (or maybe hesitated is a better word) again when accelerating from about 55 mph to 60 or so. Car has never had issues like this before, gas mileage is still in the 30 mpg range.
View 9 RepliesOkay so I have a 2003 Toyota Camry with 358, 000 miles. I replaced the transmission in 2010 with a gently used one that only had 100, 000 in it. Out had been running great until today when it started slipping in and out of overdrive. I had to turn the o/d off just to drive home and not get it over fifty. Now I don't know if I need to change the filter and fluid or just take it to a mechanic. I read on another site not to change the fluid and filter at such high mileage b/c the clutch and guys might rely on the friction of the gunk in the fluid and that new smooth fluid might keep it from running right.
View 4 RepliesSo dont know whats going on, but after my santa fe sat for a day, I went to go for a drive and when I left the house, the tranny slipped in 1st gear at around 3k rpms. The rpms just shot up, hammered into 2nd, then drove off as normal.
I couldn't get it to repeat it after that.
Facts:
-Car in eco mode
-Car sat for at least 24 hours
-Outside temp 70F
-slippage happened on takeoff at 3k rpm
-No CEL's
-around 11500 miles
What it could be? Should i take it in to hyundai? OR wait and see how it drives the next couple days.
Experience a lurch during slowish highway cruising? If I am just putting along with my foot barely on the gas sometimes the car will give a jerk or a lurch like it's trying to decide whether or not to go fast or stall. Just a really quick bit of feeback that makes me think...what was that? Here are some common elements:
-Only happens when cruising at relatively gentle speeds (100km/hr or 55mph)
-Seems to happen more often if it's windy? Has happened a few times when passing by semi trailers
-Seems to happen more frequently when there is snow on the road or blowing snow?
Could it be some sort of sensor or air filter problem? No codes have been thrown.
So I've owned my 04 Passat for almost 3-4 months now, I have a 1.8T 4Motion w/ 5speed, and love it. It will certainly be nice in the winter time with the snow and cold here in North Dakota.
I was driving on one of the state highways, and was cruising at about 65mph, when the power cut out, and giving gas didn't do anything and I eventually came to a stop. I let the car sit for a minute, tried starting and could tell that the engine was trying to turn over but wouldn't. This has happened before with my jetta, and its always been because of water in the fuel lines during a heavy rain, so I had my roommate come give me some more gas to see if we could just run the water out of the system since it had been raining pretty heavily here lately. Still no joy on getting started, occasionally the engine would turn over, RPM's would get up to about 1100-1200, and then instead of stabilizing at idle, the engine would just cut out again right away.
Got a tow from my insurance company to a local auto service shop who took a look at it and got a code saying the speed sensor wasn't working. They allegedly took it apart last night and fixed the speed sensor, had a loose wire, but it still won't start up. They've narrowed it down to the crankshaft sensor, or the entire ECU module being shot. I'll know by tomorrow if the crankshaft sensor is in fact the case.
If it isn't the crankshaft sensor, then is it definitely an issue with the ECU? Would it be worth to get an ECU pre-chipped(APR seems to be the way to go), and have that installed instead of a stock unit? Is it even possible to get a chip from these guys that comes already chipped, or would I need to get a new ECU first and then get it modded.
I did a search on the CEL P0770 and P0765 codes and I find plenty in regards to the light on but every post I have seen, says the tranny is working fine. Not the case with mine. Tranny is slipping, and if you let it sit for 30 minutes or so, it will run fine then start surging and slipping. Got to where I couldn't get it to move at all. It says B, D E trans shift solenoid for the codes. I don't want to put in this new solenoid and have not fix the issue. Is my tranny toast? Seems electrical since it will work fine once it sits for a bit. Plus, with the OD disengaged, it seemed to work fine, but even then it was acting up? I bought it used with 140k and don't know if tranny was serviced or not. I think it has due to lots of oil change receipts etc from the past 4 years..
View 9 RepliesI have a 2012 Ford 4x4 crew cab 150 xlt. 15,000 miles. When pulling my dump trailer I was stopping to turn and the transmission disengaged. Once I turned the corner coasting the transmission kicked back in again. During this happening pushing the gas did nothing but rev up engine. My dealer said if this happened that a warning light would of came on or a wrench would appear on dash but it didn't. He said then it didn't happen. This happened 3 times in 10 miles of driving. I had it in tow mode.
View 4 RepliesLet me first say that my knowledge about vehicles is nearly non existent. Yesterday I was stopped at a light on a hill. When I pulled away up the hill it felt like the tranny was slipping real bad. I coasted into a gas station and stopped. I gave it the once over look around to see if I could see anything unusual. All looked ok, so I wondered if maybe it wasn't all the way into gear or something.
I limped it home only 2 miles and it was seemingly normal although I was real gentle and it was all flat or downhill. Later that night I drove it around the block and it was shuddering and banging and seemed to be slipping again. My question is doesn't the transmission usually go over time, or does it fail suddenly like this. Could it be something else? And lastly what does a rebuild cost. Truck is 06 FX4 54000 miles 3.73 gears. Edge Evolution on level 2.
I tow a Trailer a few times a year 7000 lbs fully loaded, if I do need a new tranny should I replace to a different gear.
I have a 2013 Golf R Apr stage 2+ with about 74k on the odo. I have been stage 2 for about 5k and was stage 1 for about 20k before going stage 2. Changed my plugs and coils at stage 2 as well. So was driving on the highway at about 60 just cruising when all of a sudden there was a minor hiccup in the car and then pushed the gas pedal and nothing, RPMs started falling and then car shut off, put the clutch in and coasted to the side of the road. Tried to restart and it would not.
I have power and car tries to start but won't catch and turn over. Towed it back to a buddies shop and let it sit overnight, still won't start. started poking around. Checked Hpfp and everything seems fine, cam follower and cam are good. Noticed that when I open my drivers door now I don't hear the other fuel pump prime like it usually does and after putting hpfp back on and opening drivers door a couple times we checked the Schrader valve on the hpfp and no fuel came out like it usually would. Have it narrowed down to most likely culprits; Faulty in tank fuel pump, faulty fuel pump control module, faulty fuel pump relay.
Btw just thought of this, no check engine light ever came on, also don't have a way to pull codes.
I got a funny shifting issues that happens infrequently that I can no figure out. It happens after driving the car for a while on the highway, but not every time, and not just on the highway.
Here is my problem... when cruising down the highway the check engine light will come on stay on for a around a minute, the the check engine light will turn off, then of which my truck will lose power, not accelerate no matter how much I stomp on the gas, until my speed drops to under 55mph.
Once I get down to 55mph the truck will drop 2 gears into 3rd gear and then I can accelerate back up to speed. This will repeat every few miles. The computer will not store the check engine code, so no codes are pulled.
Cruising down the highway, my 2001 Santa Fe engine suddenly cut out. Would crank, but not fire. Not hearing a sound from the back when I flipped on the key, suspected the fuel pump, which I replaced. No go.
I'd pressed the fuel pump reset switch under the hood - checked it again. Should the switch, when it's pressed, stay in a locked position, like when you do a reset on a GFCI electrical outlet? Or is it normal for it to have the up/down 'play' in it?
Also noticed a strange buzzing on the other side of the engine compartment -- was the unit (don't know what it's called) that the throttle cable feeds into - hooks onto a pulley. The buzzing was intermittent and inconsistent, but it was happening with just the power switch on.
Oh, and did replace the fuel pump fuse, too. While it's at 280.000 miles, not quite ready to give up on 'er yet!
I just recently bought an 06 Santa Fe with a 2.7l v6. It was a rebuild. It had been hit in the left wheel. The lot put a new fender, suspension parts, axle, etc. It only has 25k actual miles.
We took it on a 100 mile trip today. I noticed if I am going up hill and it has to downshift, it feels like it looses power. The car continues to slow... Like the tranny is slipping. I stopped at Walmart and found the tranny fluid wouldn't even register on the dipstick. I bought Valvoline max life tranny fluid that matches the sp3 specs in the manual. I had to add almost 3 quarts before it was full. I think they may have forgot to add fluid back to replace what leaked out after they replaced the axle It didn't seem to work though when I continued to drive. After I stopped and let it cool about 30 minutes, it did seem a little better.
I guess my question is should I replace the tranny fluid? If so, what should I replace it with? Is there anything else what could be causing this now?
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
2000 X V10 4WD... 178K. Truck was not well maintained for most of it's existence. Drained both the TC and Drain pain and replaced the oil filter. Tranny oil looked like crude and a lot of tiny specs of metal - it shimmered in the sun... needless to say - I'm pretty sure it had never been changed.
Now - issues since I've gotten it done... Tranny has been slipping... I figured that I may not have filled it enough and after adding a few quarts, it seems to have stopped. Slipping was initially just when going from a stop.
Now it's having a problem where the engine dies when I shift from one position to another... For instance - from Park to Reverse, the engine RPMs drop as the clutch engages - but they drop from about 900 RPM down to about 500. And 50/50 chance the engine dies. Going from Park to Drive, the same thing but maybe drops to about 700 RPMs. Tried it in 2nd and 1st gear. Has happened in both. I've tried shifting to OD first before going to 2nd to 1st or vice versa and seems to behave better.
Should I flash the ECU and have it relearn the shift points? Did I overfill? Between the TC and Drain Pan - about 16 qts came out. I've been checking the dipstick - no frothing or bubbles. When running and in park - it actually shows low. Seems to drive fine once it's on the road. The engine cutting off when it's put into gear is really unexpected.
Took my first camping with 2012 King Ranch F350 and 37 feet Challenger 12k fifth wheel trailer over the weekend.
I noticed there is lot of transmission slips in first gear. Once it enters 2nd gear, no more slips.
My previous Chev 2008 2500HD diesel didn't slip much with same trailer.
Is this normal for this F350? My rear ratio is 3.55. No slips without hauling.
Maybe I need to ask dealer to check 1st gear towing?
Our FWD Santa Fe Limited had a very noticeable vibration that started around 60mph. Oddly, the vibration will sometimes come and go while cruising at a constant speed on the highway. We went about 30k miles before we had time to get it into the shop.
I asked them to rotate and balance the tires and the vibration was noticeably reduced...initially. Now it's back!
The car has ~65k miles. All 4 Kumho tires match and I believe are original from the factory. I have kept all tires inflated properly.
Our car has the optional 18" wheels. Is it common for these to bend? What else could be the cause here?
2.0L 8v ....So what's my chances the valves stayed clear of the pistons?
Driving 70mph 5the gear and cruise control set. Motor just died and I pulled off.
Cars back home in the garage. Iv ordered the ecs tuning timing belt kit.
This was a belt I installed 50k miles ago, shouldn't have gotten a auto parts store belt, or maybe it was my install, but I deff didn't think the belt was going to fail that early. Is there much of a difference between different brand belts and OEM?
OK,it's a Taurus but it's the 3.0 Vulcan.On the highway crusing easy,now and then I'll get a stumble.It's like the key is turned off and back on.The tach stays steady but the car stumbles like the key was cycled quickly.I had to put a fuel pump in it a few weeks ago and now it is starting every time but this stumble has me stumped.
View 5 RepliesAs the title says the beast died on me yesterday morning going into work.
Situation : 5 F @ 7 Am
1/4 tank of fuel that has been treated
cruising at 70 MPH on the highway using the cruise
Going into work the other day the truck died on me as i cruised along at 70 MPH on cruise, I go to get out of the way of a car. As, I step on the accelerator X falls on its face. I look at the dash and there are no idiot lights on, gauges all look good. I navigate to the shoulder 3 lanes over and park it. As soon as it is in park it dies and will not restart.
I call AAA and sit there waiting for the truck to show up. After about 10 mins I try to start it again it stumbles and dies. 2nd try it fires up and is running rough. I make it to the nearest gas station and fill up. Then I go to the parts store and pick up the 911 fuel treatment and put it in the tank. I also use a scan tool on it and no codes. Truck ran fine after all this.
I go to start it after work, it starts and dies. I start it again and it sounds like it is running on 2 cylinders and there is a large puff of smoke out the exhaust which goes away after it is started.
After it warms up it runs and drives fine, no issues! So I looked at my extension cord I plug it into and realize that the timer was bad. New timer and verify it works. Go to start it today and it starts right up and idles and runs fine. Is it possible that the fuel gelled up due to the timer being bad and the block heater not turning on? Or am I missing something?
I recently purchased a 2015 Elantra a few months ago and I have noticed a couple times now that when I'm driving along and hit the gas when I'm trying to pass someone or speed up in a hurry that it just revs high but doesn't catch until it revs back down. Is this a normal thing these days or could it be a problem? It's an auto. Also the other day I had the window down and I heard ticking noise sounded like it was coming from the front left but it followed my speed. Hit the brakes and it didn't change but it slowed down when I slowed down. Then I turned and it stopped and haven't noticed it since but I haven't really gone too far.
View 3 Replies