Occasionally I experience a temporary loss of power when I try to accelerate. I press on the accelerator and nothing happens -- then finally catches a second or two later. Usually it happens at lower speeds as when turning a corner in town or when climbing a hill.
View 2 RepliesI own a 2000 7.3 6 speed with 175,000 miles. I just bought it less than a month ago and it is my first diesel.
About a week ago I stepped on the gas and it just had nothing. I have a TS 6 position chip that I unplugged as soon as I noticed the loss in power. When I first bought the truck it was incredibly fast and now it has nothing to it at all. I have to have it higher in the RPM's to go up hills (especially when its not warmed up). If I push the pedal down it will sound the same, boost will get to about 14 (without chip) and the truck doesn't let out any smoke but it just doesnt have any power at all. I recently towed another vehicle on a trailer and it really struggled with it, more than I thought a diesel should.
When the chip was in, the truck would let out black smoke even after I noticed the loss in power. That made me think that the engine was getting enough fuel. I thought there could be a boost leak somewhere but it still builds 14 psi. However, I do not feel boost kick in at all! When I first got the truck it would only build around 14-15 stock but it felt a hell of a lot faster and I could feel when boost would really kick in. I took off my intake and looked at the turbo and the fins are in great shape and there is little to no play.
What the problem could be? I don't have very much money to start dumping parts into the truck and Im not sure what to do. I guess my questions would be:
1) Is it a boost leak, fuel problem, or something else?
2) Could a gelled filter give me these problems?
3) What should I do and where should I start?
A little background first on my 1999 Ford F350 7.3. A few months ago I noticed i had fuel in my coolant which lead me to a cracked injector cup. I replaced all 8 cups and since I had it apart, and I bought the truck used and didn't know what had been serviced, I replaced the injector o-rings, glow plugs, valve cover gaskets, and valve cover gasket wiring harnesses. Got it all back together and had been running great.
About a week ago I was parked with engine running and the stereo suddenly turned off. A few minutes later I turned the truck off and turned it back on about 10 minutes later and it wouldn't start. Batteries appeared dead so I jumped it and made it home. Took both batteries down to AutoZone and since they were under warranty got two new ones. Figured out my alternator was bad and not charging my batteries so I ordered a new one.
Up to this point truck has been running fine. Truck had sat in my driveway for the week while waiting for the alternator. While I was out of town my father in law went to use the truck and noticed it wouldn't start. He hooked some jumper cables up and got the truck started. He said as he drove off the truck had no power and smoke was pouring out the exhaust.
I charged the batteries and installed the new alternator. Truck starts great and seems to be idling normal. When I took it for a test drive it has no power when accelerating and black smoke pours out the exhaust. The truck will barely make it up any type of incline.
I thought maybe it was the injectors not firing. Wiring harnesses are plugged in and do not appear to be damaged. I did not remove the valve covers yet as it's not difficult but time consuming and I figured since I just replaced all of it that it should be ok. I did a buzz test and all injectors passed. I get no trouble codes or check engine light.
I have an 03 6.0 Power stroke. My problem all started the other day when I started to occasionally not get any boost on acceleration and lose of power and a lot of vibration like it's about to cut out but it got worse now today I drove it about 5 miles into town when I got to town I noticed a rough idle I got gas in a gas can not in the truck. I got back in to leave and I had absolutely no power at all the truck stalled out and it was very hard to start finally got it started and it runs really rough almost like it's going to shut off.
So when I started driving I would only make it about a mile or so with out it chocking out and having to let it site for a minute or two and start it back up and go another mile or 2 and have it do the same thing all the way home all the time I have vary little boost if any at all except for when I first pull out now oil pressure is good and engine never over heated some of the codes I have is an EGR code and a contribution balance code for several cylinders I was thinking possibly a maf sensor or a clogged egr not working right.
My 2001 VW Passat 1.8T manual transmission is experiencing loss of power/hesitation during acceleration. Occasionally the check engine light will blink for about 10 seconds during this time. My valve cover gasket blew about 7 months ago. I had it replaced along with 2 ignition coils. Since then I have had replaced the other 2 coils and spark plugs because of this recurring problem. I have also replace the mass airflow sensor for the second time. The diagnostic check continually shows misfires in different cylinders for which I again tried replacing the coils. I have also received the codes for "fuel mixture too lean" as well as for too rich. What could be causing this?
View 4 RepliesI was cruising on the highway and tried to accelerate and no more power. Could feel engine losing power. After I shutdown the car and start again, car was fine.
View 3 RepliesI have a 2000 gmc jimmy 300.000 km 4.3 vortec .starts ok, even when cold idle smooth but when I accelerate past 2000 rpm it has a complete loss of power. I bought a fuel pressure tester key on 2 seconds 60 psi when I start the vehicle and running 55 psi. I took it on a road test it stays at 55 psi and has a hard acceleration and will go to 60 psi ,and then starts to break up my first question is how can I block off the return line to the tank, there's no rubber hose in any of the connections just steel lines and hard plastic with push connectors, is there a plug that you can buy or how I can block off the return to see if the pump will build pressure to 75 psi to 80 psi will this will tell me whether the pressure regulator is faulty or the fuel pump needs to be replaced.
I have a manual its a Haynes for chevy blazer gmc from 95 to 2004 it says with central sequential fuel injections (csefi) key on engine not running it should be approx 55-61 psi the engines running at idle it should decrease through 3 to 10 psi according to this manual i am within range but i have read on other posts that it should be 60-65 would you say that my 55 psi reading is okay? or should it be 60-65? also when i blocked the return line should i get a reading of 75 or higher? if the reading goes up does that mean that the fuel regulator is faulty? and if it doesn't go up does that confirm that the fuel pump is the issue?
I have a 04.5 GLI 1.8t, performance mods include, cone filter on the end of my maf, silicone TIP, Forge splitter, 3in custom tbe and unitronics stage 2
I started noticing this problem on the day I got the car tuned, I hadn't noticed it before hand. I replaced the spark plugs and it worked a little, but it continues to do it.
The problem: When I get on it at WOT under full boost, around 2500 rpms, the car loses all torque, misfires spits and sputters throughout the rpm range until about 5300 rpms then it all of a sudden has torque and pulls great.
I don't have any boost leaks that I know of along with vaccum leaks. There is no flashing cel or misfire code for my coil packs. Can this be a faulty n75 valve? if so what could fix it?
I am the original owner of the car, which has approximately 125k miles on it. The car has given me great service, but lately a strange problem arose that has my mechanic stumped. When I try to accelerate, the car typically does not respond. After 5 seconds or so, the engine suddenly comes to life and the car begins to accelerate. At high speeds it is not an issue, but the engine sputters once in a while. It has never stalled. It is not the transmission because the RPM stays low during low-power times.
The mechanic initially thought that it was a dirty fuel filter. But, changing it has not worked. Once the engine light came on, and the code was for the air-flow sensor. But, the mechanic is not convinced about that.
The problem tends to become worse after driving for a while, after the engine has warmed up.
2009 LS460 I have had my car at the dealer a few times for loss of power on acceleration. The last visit which lasted three weeks finally gave a diagnoses. The problem was confirmed by the dealer and the factory reps, a knock sensor picks up a signal that retards the timing resulting in no power, I was nearly run over by a semi the last time it happened. They tried to give me my car back on 7/24/14 with the knowledge that the problem is not fixable at this time but I should drive the car and they will tell me when there is a fix. I left the car at the dealer. I was also told that they had a few others with the same problem that could not be fixed.
View 14 RepliesI have a 1999 Mercury Mountaineer 5.0L V8. It just recently began acting up. After warming up the engine goes through heavy power loss and inability to climb ANY hill. Usually cannot get above 30-35. I just recently replaced plugs and wires for a tune up and a faulty coil pack (approximately 5-6 weeks ago) causing a misfire on 8. Today in troubleshooting I attempted the "Backyard Mechanic" trick of unplugging the MAF sensor and took it down the road, no change at all in acceleration issues or on idle, truck runs the same. Unable to spot any exhaust or vacuum leaks or issues, recently cleaned MAF housing and changed Air Filter as well. All of these issues arose after a heavy ice storm, do not know if this had any impact or was just bad timing.
View 5 RepliesBought my first Hyundai, a 2013 Accent last Saturday. Love almost everything about the vehicle.
It is equipped with the EcoBoost which I can turn on and off.
Noticing when I accelerate almost every time there is some initial acceleration and then a noticeable power loss. It's much worse when I'm accelerating through a turn.
Honestly it's hard to tell too much of a difference with the EcoBoost and AC off.
Also noticing the car really surges at times with the cruise control on. Obviously if I hit an incline it's going to boost a bit, but sometimes even on very minor inclines or straightaways the RPMS just fluctuate more than they seem to need to.
Wondering if this is normal for this engine and something I need to get used to. Coming from a Honda Civic I didn't experience this consistent power loss / fluctuation.
Lately having the following issues with my Tig.
When starting up the engine on cold start (or after having the car sit for about 30 minutes) after about 10 - 20 seconds; pretty much right after first acceleration the car all of a sudden looses all power. RPM fall down even when accelerating. Accelerating more only let's the engine stall more.
5-10 seconds later the engine functions normal again.... What problem could that be ?
Having problems where sometimes the car won't go into gear, other times it's fine? The problem started after some hard acceleration in 3rd, there was what felt like a momentary loss in power. I dipped the clutch as I thought a boost pipe had popped off, all was fine (still seeing boost when revved). After this it got progressively harder to get gears, finally resulting in not being able to get into gear at all.
I found I could get it into 1st with the engine off and could go up gears normally, but couldn't change down without stopping and turning the engine off. The clutch is working fine, the biting point is normal. The problem seams to come and go randomly, it will work fine for a while and then start playing up again. When working the gearbox feels normal, there is no grinding or wining noises. I can move between gears normally and do clutch less gear changes.
There is now a vibration which can be felt at 1000rpm when stationary. It feels like it coming from the engine/gearbox and seems like something is out of balance as it shakes the whole car. The car is on 91k, supercharged running 470hp & 370lb/ft (at flywheel) and is fitted with a Spec stage 3+ clutch and solid flywheel.
We have a 2002 Sante Fe with v6 and 270,000 km on it. Just had extreme loss of power and jerky acceleration from a stop. This has happened a few times in the past year and each time with a 1/4 tank of fuel? We pulled into a gas station, filled it up and away we go like nothing was wrong?
View 4 RepliesI have a 1994 Oldsmobile Cutlass Cruiser 3.1 with an intermittent engine power loss during acceleration. Usually it occurs just after leaving a stop sign or light once or sometimes twice in a row. It is not a hesitation - it is a very abrupt loss of power. I've kept up on the standard maintenance very well and the car has 80,000 miles, so I would not suspect spark plugs, wires, or fuel filter. It does not have a tachometer, but I am 99% sure the transmission is not slipping or jumping out of gear, but that the engine is actually loosing spark or fuel. This problem is very intermittent, but it has triggered the check engine light a couple of times. The check engine light does not stay on, and when I took it to my mechanic he said to keep driving it until the light stayed on or the problem was more easy to replicate. Right now, if a mechanic went for a test drive, there is a good chance it would not show any symptoms. My mechanic did mention that it may turn out to be an ignition module.
View 3 RepliesI have a 2006 town and country with a 3.3 and 220,000 miles.
Last week I was having some hard starts and loss of power on acceleration. My check engine light flashed during one episode so I had autozone check the code and it showed a misfire. I changed out my plugs and wires and that solved my issue. It started and ran like new.
Yesterday, I was running errands and my charging light came on. I was about ten miles from home and I decided to go for it. It was night so the headlights were on. Along the way, everything started to dim. Headlights, dash lights, airbag indicator came on and then the van just died. I walked the final mile and we towed it home.
The alternator and battery were both replaced last year in November making them both one year old. AC Delco battery 660 cca and I had a very reputable alternator shop rebuild the alternator.
So before I towed the van home, I hooked up some heavy duty jumper cables from a running chevy venture and let it charge 15 minutes. After the 15 minutes it was just clicks in rapid succession.
I hooked it up to a trickle charger overnight, 12v 2 amp setting. This morning, the van started, idled fine for about five seconds and then started trying to cut out. I kept it running by giving it gas but after about twenty seconds it stalled. I tried to restart and nothing but the rapid clicks. Three more hours on the trickle charger and the same exact thing happened. It started, began to stall, quit and then wouldn't restart.
I noticed today that the power steering reservoir was leaking a decent amount of fluid down onto everything around it including the coil pack. I replaced this today and used brake cleaner to clean all the surrounding components.
After doing some internet sleuthing, I found a thread with the same problem. For this guy, he had a disconnected ground from the negative battery terminal. I chased mine down (G101) disconnected and wire brushed it all clean. Put it all back together and still the same problem.
Here is what I have discovered:
Trying to jump it from another vehicle only results in the clicks. This is true whether the jumper cables on the dead battery are on both terminals or the negative is grounded on the motor. If the battery were the problem, I should be able to jump through it. If the alternator were the problem, I should be able to start with a jump.
After charging the battery, it will start once but then die soon after. Battery with the key off will read just under 12 volts (11.9, 11.6). With the key on, it will drop to the 8's (8.6, etc.) I have not yet had the battery or alternator bench tested. I plan to start with the battery in the morning.
It seems to me that the alternator wasn't charging the battery or it wouldn't have just killed the battery as those accessories should be powered by the alternator. It shouldn't be a starter issue since it will start after being on the trickle charger.
I have an 2004 treg V10. I put in diesel yesterday morning(10/13/2010). I went to work, everything was fine. On my way home I started feeling a slight hesitation and sputtering in the motor. It's something that I noticed but didn't give much thought. 10 minutes into the drive and the sputtering became more noticeable. To the point where I would floor the pedal and the treg wouldn't go anywhere, it felt like all the power got drained from the motor. I came to a stop, and listened the engine, no noticeable change in engine noise. Everything seemed fine, but the truck was sputtering every time I would press the gas pedal. I parked the truck for the night and forgot about it.
Now this morning. Driving around in some local streets I def felt like something was off with the truck, it felt like it had a V6 not a V10. took it on the highway and opened her up, car took way too long to get up to speed and once it reached 90 MPH it didn't want to go any faster, it just stayed there. I took an exit off the highway and stopped at a light and the car sputtered and hesitated and eventually stalled at the light. I tried re-starting the truck and it was just stay in the crank position. The battery light came on. I tried starting it again and it would just remain in the crank position. It eventually turned over and started after cranking it for about 5 or 6 times. But the car is still sputtering a bit.
2008 GS460. 100K miles
I have noticed when I accelerate on a entrance ramp to the highway I notice the RPM meter jerks a little like it's trying to suck for gas or something else. I can feel it in the car too. This is the only time I have noticed this. I have replaced the spark plugs about 5K miles ago.
I did bring it into the dealership a few months ago to get the fuel pump replaced as I noticed a hissing noise under the drivers side read door. They said fuel pumps rarely go bad on the Lexus. The mechanic did some fuel pressure tests and said everything looks good. He also said noise is the return line back to the pump.
I was driving my 2010 Prius on the Highway (less than 2 miles) and the engine check light came on.... shortly after the ! (triangle with exclamation light came on and then started flashing). I exited the highway and was going back home. On the way home, I noticed a decrease in acceleration and then a message 'Hybrid...'
I was able to coast into an apartment complex and then got a ride home.
After about a couple of hours, I went back to the Apartment Complex. I reviewed the manual and one of the options was to check the gas cap. I filled the tank up last weekend and haven't driven it since today.
So my 2005 elantra 2.0 CVVT has 189k on it 1 owner.
I got a check engine light one day and i read the code. Came out to be 02 sensor code bank 1. So i order a denso o2 sensor and replace the part.
I drive the car for about 400 miles to reset monitors and get a check engine light. P0420 cat code. At this point the car drives with normal power and pickup.
1000 miles later my car has lost power. It doesn't have any get up or power when driving normally. I take the car to my local shop and they recommend replacing front cat. I replace front cat, same issue.
At this point i'm not sure if it is a transmission problem or maybe my 2nd cat or something else?
On the freeway if I put my pedal to the ground the rpms surge up very very slowly,
Also seems like the car doesn't shift till around 4k rpms, seems like previously it shifted sooner.