Touareg :: Engine Stalls At Random Usually Happens At Low RPMs
Jun 23, 2004
I got my Touareg 2 months ago, and has been nothing but trouble. I also own a 1997 E39 BMW 528i, and I have never had so much problems with it in 8 years as with the VW in 2 months. Just plain terrible. There is now a strange problem, and it looks like the local service could not localise it properly.
My engine stalls at random. It usually happens at low RPMs, at a red light stop, etc. The engine usually goes bananas, the revs going up and down, and it looks like its choking. Sometimes switching to N and then pressing the revs up a few times works, but not always.
Sometimes the EPC and the triangle (exclamation mark) lights come up, but not always. It happened to me, that the engine just plain stopped.
It even happened to me when I was going slow down the hill in front of my house!!!
Can you imagine, initially I was firing up the engine with the button, having the key in my pocket.. And when the engine stalled, I lost all the servos, and the steering wheel just LOCKED!!!
I mean this is really serious. Since this happened twice, I am always using the key in its place... The local service just changed some electronics which supposedly monitor the engine RPM. It did not work...
View 10 Replies
Advertisement
I have a 1998 Accord, 4-cylinder VTEC standard transmission, 226,000 miles. Last fall I first experienced a problem with the car where within 5-10 minutes of starting the engine and driving, the engine seems to lose power/fuel and RPMs act as if they'll drop low enough for the engine to stall. If I take my foot off the accelerator, and reapply, the engine seems to gain power again.
Also, if I open the accelerator to full while the problem is occurring, it can occasionally "push through" and gain power again. Similar things will happen while stopped. In neutral, RPMs fall low and suddenly jump back up and then settle into normal idle. The problem never persists longer than 10 minutes within starting the car.
I took my car into a local shop that came recommended by a friend. They investigated a "check engine" light that didn't explain the problem and were never able to recreate the condition themselves. They replaced a few parts but lost the work order so I don't even know what they changed, but the problem seemed to have solved itself for a while. Recently it started up again and I would love to sort it out.
View 2 Replies
Experienced a ticking noise when at WOT with the 4.2 V8 engine? When cruising around the engine sounds fine, but when floored the engine (i believe) is ticking at higher rpms. Hard to believe its the engine, only 24k miles on it, with regularly changed oil. Sounds like either detonation or valve interference.
View 10 Replies
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 Replies
2006 LaCrosse stalls at random when a/c is on under 30 mph. it can go all day without a stall or can stall 10 times on a short trip. diagnostics shows nothing and every mech who has seen it is stumped including dealer. car restarts immediately and has no other symptoms. is it haunted or what?
View 7 Replies
I have a 2000 crown vic, police interceptor..... 1st.. car started idling rough had the codes read gave misfire on 4 . So we had the boots and spark plugs replaced. Car ran fine for like 3 days then engine light came on again.. running rough... code read misfire in 8 so had the coils on 4 and 8 replaced... ran fine for all of 2 weeks. Again engine light came on... now showing a misfire on 7, but car runs fine..??. Anyways I noticed my battery gauge was marking a really low charge... but as soon as I would get on highway it would jump back up to normal...
It did this for a couple weeks, then I noticed the gauge was marking really low car was losing power... I have a new battery and alternator on car already. But still I had them tested; both tested fine... Then car kept stalling at stop signs ans red lights went ahead and exchanged alternator 4since its under warranty anyway. This cause the charge gauge was reading normal.. but car still kept dying... so replaced fuel filter... didn't replaced tps and mass air flow sensors too...but it still keeps dying on me. Now codes are coming up misfires on 4&8! Why does my car keep stalling and what would cause these random misfires especially when these coils have been replaced already???
View 5 Replies
I have recently had some problems with my 2001 Yukon, it a 5.3L and has 4x4. when I accelerate I get about 2000 RPMs maybe and can barely get above 35mph. I brought it to a local dealer for a diagnosis and was told I had a bad catalytic converter, four bad O2 sensors and bad injector connectors. I've replaced the injector connectors but its still acting up. I don't want to spend the 700-1000 on a new catalytic converter when I can just replace the sensors.
View 4 Replies
I was running in a track day at Sebring today and missed a shift. Rookie move...the car eventually went into limp mode. I took the car back to the pits and scanned the codes. Limp mode was confirmed in addition to a cylinder 4 misfire and a random/intermittent misfire. Cleared the codes and went back out; couldn't even finish the lap before the car was thrown back into limp mode.
I was able to hobble home by keeping the car out of boost and started trouble shooting. So far I have ruled out spark plugs and coils. Should I be looking at the injector next? Any chance I bent a valve? The misfire can be triggered by putting the car under a load and bringing it up to 5,000 RPMs or higher.
View 24 Replies
I have a 1991 Chevy Lumina and I believe this wire is the root of my problems. I
wasn't the one who unplugged it but it seems it was unplugged as an easy way to get around a problem. When unplugged the car runs but the performance is off, It doesn't feel like it has the same power as it does when it's plugged in and it also sounds different when in idle. When the wire is plugged in the car stalls while driving at random intervals between 1 and 10 minutes and needs to be jumped to start it back up. I will attach pictures of the wire and its location within the surrounding area.
View 1 Replies
I have a 1999 B4000 V6 4.0L with 78K miles on it. I recently had P0171 and P0174 error codes come up. I replaced the MAF sensor and have not had the codes return but now the truck will basically stalls out when sitting at a stop light. It does not do it all the time just randomly. It has never done it when engine is cool but only once up to temp. The idle is smooth at cold engine but begins to get rougher once warmed up (nothing too bad just noticeable). I cleaned the IAC with MAF cleaner but no joy. I reseated all plug cables at the coil but no change. RPM around 600-700 then fluctuates up a bit then truck will stall quickly( I usually cannot put other foot on gas in time to get it to increase RPM before it dies)....
View 5 Replies
I have a 2005 Camry SE V6 with 73000k I just got it out of the body shop yesterday and everything seemed fine. i started the car up a short time ago and it stalled out when attempted to drive away. its idling at 400 rpms? I feel that the guys at the shop disconnected something.
View 1 Replies
Every so often when I leave the car sit for 30 minutes after being driven, I start it up, put it in reverse and back up, then when I put the car into drive the RPMs drop for two seconds or so and it seems like it wants to stall. After that happens, all is well and the Tig drives normal.
I scanned the Tig and it came up with a "low fuel rail/ fuel pressure" code. It happened 5 times.
Is my fuel pump going? Maybe a dirty fuel filter? Or maybe a computer problem?
Info: Tig has 26k miles on it, stock computer (not chipped), it is out of warranty. I only run 93 octane in it too.
View 13 Replies
I have a 2001 Hyundai Santa Fe LX with 214,000 miles on it. In general, I am having two problems which are most likely related. I would like to get opinions on what is causing the problems, how to fix the problems, and what the cost might be for the fix. This is an older car and I don't want to bring it to a mechanic to just do searching.
1. RPMs fluctuate quickly at slower speeds in town stop and go traffic and while parking in Drive or Reverse. Fluctuation can be between 1000 to 2000 and 3000 RPMs back and forth.
2. Car stalls while sitting at stops when in Drive. When car stalls, RPMs have suddenly decreased to 0 (zero).
3. RPMs fluctuating and car stalling typically occur after I have made my first stop and have turned off the car.
There is also a Check Engine Light Code: P0304, Cylinder 4 Misfire Detected. I changed the vehicle speed sensor a few months ago.
Here are the details of what has been happening, when it happens, and what I have tried.
- When RPMs fluctuate, the car slowly accelerates and slows down and I can hear revving high and low. This happens when the RPMS fluctuate just a few RPMs around 1000 and when the RPMs are fluctuating up to higher RPMs.
- After the car has been driven for about 45 minutes and car is at slower speeds, RPMs will fall to zero while at stop and in Drive, and the RPM fluctuation will begin.
- RPMs jump to 2000 or 3000 and stay there but do not fluctuate when car is put in Park and Neutral.
- When car is in Park and at 2000 or 3000 RPMs, car takes a few extra seconds to turn off.
- Car accelerates without pressing gas pedal and will accelerate up to 40 mph.
- Car will sometimes lurch at slower speeds of 15, 25, and 35 mph when RPMs are fluctuating or when the gas pedal is pressed.
- When RPMs are fluctuating and at 1000 or higher and I am pressing the brake to slow down, the car fights in Drive and in Reverse.
- RPM fluctuation does not occur at interstate speeds.
- A couple days ago, when I was at interstate speeds of 60 to 75 mph and pressed the gas pedal, the car would stutter and jerk.
- RPM fluctuation and stalling primarily do not occur when the car is started at the beginning of the day or when the car has been off for several hours.
- Twice In the last week the RPM fluctuation and stalling occurred even after car was not started for several hours and after only about 5 to 10 minutes of driving in town stop and go traffic.
- Sometimes car stalls when I'm at a stop and slightly press the gas pedal to start driving.
- There are times in town traffic when the car is operating normally and is at 750 RPMs at stop, then the RPMs suddenly decreased from 750 to 0 (zero) and the car stalls.
- From Neutral, sometimes when I simultaneously put the car in Drive and press the gas pedal either by feathering or forcefully pressing pedal 3/4 to the floor, the car would have a delayed reaction to accelerate but would not shut off.
- After car has stalled, if I try to start it right away, the car cranks but does not start for about 5 minutes.
- The time between stalling and being able to get the car to turn back on has increased over time from starting up at first crank to not starting for 5 minutes.
- If I let the car sit for 3 to 5 minutes after it has stalled, the car starts up but takes a couple seconds to start while pumping the gas pedal.
- Issues have been happening since November but are getting more frequent.
- Stalling is happening more frequently and within minutes of each other.
View 10 Replies
I have '05 Camry v4. Everything was fine but three days ago I started to have issues. At first I tried starting the engine it would fire up with RPMs going to about 2000 as per usual start. Instead of going down to 800 as it usually does the RPMs just keep on dropping until car stalls. On the first day it started happening I would simply try to start the car again and it would start.
Progressively it would take me more tries to start the engine. It's always the same way (be it a cold start or a start after I've just drove for a while). First try - the engine starts and stalls right away and after that I have to keep on trying to start it for some time. So finally it wouldn't start at all. Starter cranks, battery fine, but the car simply would not start. Weird part about it, is that once the car starts it acts completely normal. No spikes in RPMs, no loss of power, nothing! At this point I just don't know what the hell it is.
View 7 Replies
1st problem is shifting from 1st to 2nd and sometimes from 2nd to 3rd though, 2nd to 3rd is not as bad as from 1st to 2nd. It stumbles and gets really bad if I don't let up on the gas. After the initial shudder it will go into 2nd just fine. I also have to gun the gas a little bit when I first start the car, or it will just sit there and idle and never go into gear.
2nd and more annoying is that it stalls after driving around a bit. It happens on freeway or city. It doesn't stutter or anything the rpm's drop to 0 and it just stalls and won't start up for a 5 - 10 minutes or so.
Codes pulled are P0731, & P0736. The transmission was replaced about 2 years ago with a refurbished one. Could it be going out again already? The guy at Autozone suggested replacing the TSS (Transmission Speed Sensor?) to see if that was the problem. I have not done this yet, but plan to.
View 3 Replies
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 Replies
I have a 2001 Ford Escape, and when I start it for the first time of the day, it idles really rough, and way below 500RPMs (to the point where it almost stalls). After about 10 minutes, when the car is all warmed up, it runs smoothly, as if there was nothing wrong with it. The only conclusion I can draw is that it is temperature related, but I can't figure out exactly what is causing the issue. This happens on the driest or wettest of days, so moisture doesn't seem to be an issue.
View 2 Replies
Have a 2001 CRV that is running really bad. It almost stalls when I put it in gear or even when the RPM's fall to idle. It is now throwing a p0172 code. I have a simple scan tool and verified the MAP reading and primary O2 voltages as suggested by the manual, both appeared to be normal. It seems all the symptoms point to valve clearance, however the valve were adjusted not 2000 miles ago by the dealer during the 150K service, and this issue has existed before and after that adjustment. I also cleaned the IAC screen with no changes.
View 5 Replies
I have a 2003 Camry 3.0l v6. Stalls at lights random.
Currently the car stalls at stops but this doesn't happen all the time it can go a month in between the problem occurring its very random. While sitting at a light the rpms drop and then it revs up and cycles like that for quite a while. This will also occur while cruising at a low speed while I'm just coasting the rpms will go up and down. I can compensate while stopped by power braking and keeping it at its normal idling rpm. I have no check engine lights and can't seem to determine what would be causing this issue.
View 5 Replies
06 Elantra Limited, 96,xxx miles. When I'm idling at a light or something, the Rpms drop for a split second, almost to the point of stalling, but recovers. Happens in a split second. Does the same thing even when driving, but does it more frequently when idling. It even does that when I first put my foot on the throttle to accelerate from a red light.
I've cleaned the throttle body but it still does it. I've taken it to 3auto parts stores. One said that battery was bad. The other said the battery is fine but alternator is producing low. The last said both are fine.
View 11 Replies
I purchased a 92 Lumina Euro with a 3.1 and 101,400 miles on it a little over two weeks ago. It has been having problems since I got it.
It stalls intermittently, typically after I drive to work, shut it off for two hours, and then start it to go to my next client(home health aid) sometimes it stalls right after starting it then, and/or sometimes when put in reverse and/or drive and occasionally at stops signs after the aforementioned problems occur. It has also stalled out twice after highway driving after the car is shut off and started shortly afterwards, for instance, when I ran into a tobacco store for some cigs.. After the problem occurs it usually drives ok if I continue to drive it awhile even if I shut it off for a short time and restart.. I added some fuel injector cleaner when I filled the tank but it didn't work.
After about a week of the stalling issues the car refused to start after dying and didn't start for two or three days. As I was unable to get an answer from the dealer my step-father, who went with me when I bought the car, called him and he said if I could get the car there he would fix it. So I borrowed a bundle to have it towed the 25 miles or so to the small town car lot.
His mechanic supposedly fixed it by replacing the TPS and the dealer informed me that they had cleaned the throttle body before I bought it and apparently the TPS needed replaced to. However the issues again started after one day of it running fine. I tired to get a hold of this guy again and again I get the voice mail and no return call so as soon as I got off work I drove it over there and again he said he would fix it. He had it for three days and I again tried to get a hold of him without success and he again answered the phone for my step-dad and told him they had ordered some kind of module that would be in Monday. So Wednesday he calls me and tells me that they didn't replace this module because when they took it out it tested good five times but they noticed some gunk build up at the contacts of the wires that hook to the module and now the car was fixed. Why did they order the part before testing??? This doesn't make sense so it throws doubt on what the man said. I went to get the car and when I got back to my town and went to get those cigs it died twice after restart and put into reverse. That was two days ago and it has been dying once or twice each day since then although it is somewhat better than before as it isn't taking as long for the idle to even out at sufficient rpms after I throttle it at idle or drive awhile. BUT now it seems to be sucking the gas hard and I am wondering if this guy just did some jerry-rigging because he sure isn't fixing it.
A few more details. The rpms drop rapidly when this occurs, it has a couple of times had a rough idle at the same time but more often the rpms drop and it dies.Sometimes if I use the throttle and keep it up around 1000 rpms for a short time it won't die. I have smelt a burnt smell a couple times when I shut the car off, like electric burnt, not oil burnt or stinky exhaust. Lets see, I felt a very brief loss of power feeling when driving on the highway on two different occasions, so brief that it was barely discernable. It runs over the halfway point on the temp gauge after driving awhile in town, seems a little hot to me but I read these cars don't kick on the fan till 220. Sometimes the rpm bobs a little up and down at idle and slow speeds and once the battery power dropped and popped right back up when it was idling funny and when it had that no start an acquaintance tested it by putting a screwdriver in a plug wire and pointing it towards the engine as I cranked it and he said it had no spark and it did crank every time I tried to start it during the no-start condition. It has also done a bit of surging from time to time when the prob happens. The car is recovering from the stall condition quicker than it did before since this last "fix" but still stalling.
View 5 Replies