I'm curious to know if it is theoretically possible to (some-day) swap out the V8 gasoline engine w. a VW DIESEL/Turbo power plant. Are any of the VW Diesel engines directly compatible w. the V8 transmission, mounting brackets, electronics, etc. etc. The Glow Plug indicator in the dash, though not required for me, would be nice to have as a reminder.
View 9 RepliesNeed to know if you can mount a 04+ turbo on a 03 engine without changing the intake with the cross in the back ? Or does the intake have to be changed. If the intake does need to be changed will the egr need to be change as well ?
View 4 RepliesDid the swap and all works good except the boost is often at 3psI then sometimes it works good. Used the 03 harness. So did I need to change a wire or sensor or use 03 pcm?? I was told maf sensor might cause issues but no codes for it.
View 10 RepliesI bought a 2011 F-450 with 205,000 Miles on it with a blow engine. Local shop installed a Ford NEW complete engine. Unfortunately we had Code P24A5 EGR Cooler Bypass Control Stuck after the swap. Truck drives fine just has CEL on. Goes to FORD and they test Vacuum from engine, on line, and on compents say all is good. Replace Vacuum switch and Control and neither fix it. Ford stumped and quits responding. So i go get my truck back since they wont respond and had it over 2 weeks.
I get it back and now it has Codes P04DA Closed Loop EGR AT Limit - Flow to high and P1102 Mass Air Flow Sensor in Range but Lower than expected. I also have a P21BO for the reductant level sensor "C" Circuit High.
Since picking it up from Ford, Truck has almost no throttle until oil temperature warms up. I clear codes, truck runs good after warming up and no CEL comes on. Drove it for over an hour. Next key cycle, and CEL is on with all the above codes. Could something be hooked up wrong? Where to start?
Check engine light is on says low turbo boost but gauge says it has a lot of boost. Only happened after I put catalytic back on for smog test. Before that no problem.
View 10 RepliesIt started after a blue spring upgrade. my turbo would not spool until we revved the engine hard then it kicked in and it's kinda worked since then.. it feels like the truck is struggling on acceleration and the boost builds fast up to 30lbs, the EBP seems to be stuck at 21.48psi until your in 3rd then it jumps and I have power again, also the turbo dumps (farts) if I let off even a little until the EBP jumps then no issues. I replaced the sensor and it's stuck at 21.48 all the time.
Now, I unplug it and it jumps between 26 and 28psi, plug in the old sensor while it's out laying on the motor (not installed) and right back to 21.48. I don't know where to go with this and it's my only truck so I need it running. also it was blowing the intercooler boot off at the turbo during a normal acceleration and the turbo spool has a howl to it when EBP is stuck...
My 2004 V10 was loosing power, the check engine sign went on, and it actually stopped running. I got it to the dealer in limp mode. After checking the fault code with VW the dealer said VW told them to replace both turbos and both ECUs . Of course the engine had to be dropped etc.
What are the chances that both turbos fail at the same time? Would not one exchange lets say the ECU first and see if that fixes it? The turbos looked fine when they had them out???? The guys at the dealership were great, making it as smooth as possible, but could not fully explain it to me either....
From what I've read they are a direct replacement to our 6.0 trucks. This one looks alittle dirty but it only has 100k on it. Comes with a 90 day warranty.
What do you think, go for it? Should I upgrade my wiring battery cable wiring and grounds while i'm in there?
[URL]
Curious how it went and what additional hardware was needed.
View 8 RepliesI have a 06 f350 superduty with a 6.0 I have had injector problems before with the motor even hydro locking no start this is the problem my truck started blowing white smoke with a strong diesel smell everyone said it was oil cooler but I took it to a ford garage the guy said I had 2 injectors hung open and wasn't hydro locking and suggested to put all 8 in so I did 3400.00 not I went to pick it up had no power at all turbo was not kicking in so I took it right back to them they checked it out said turbo was sticking had to clean it it would take 6 hrs. said the fuel In the motor caused it it was working fine when I took it to them now they say maybe a new turbo are they giving me the run around or is this possible....
View 9 RepliesThe beast slowed to a crawl on the interstate saturday morning for my son's soccer games... wouldn't hold speed up hills and engine had definite shudder at all speeds... fortunately, the dealer is in the city he was playing in adn the service dept is open on saturday mornings, so I could drop it off... they were exceptional about getting a loaner (new jetta tdi wagon)... they called today to report that one of the turbos was ruined... VW says they have to replace both to complete repair... tracked down parts in germany and will take about a week to arrive, then a day or so to repair. Had problems with the v10's turbos? I'm at about 12K miles... this is my second v10 and it's kinda spooky to have this kind of problem...
View 20 RepliesI have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 Replies2005 F250 SD, Crew Cab, Diesel 6.0L...
Hauling my jeep (close to 16,000 pounds all in F250+trailer+jeep) on a highway going a little over 70mph up a hill when I seemed to have lost some power and the check engine light came on. The turbo PSI was well over 20PSI (according to the gauge in the dash). I have a Scan Boss but I have not been monitoring turbo boost PSI.
I was only 10 miles from the final destination so I continued without stopping. It seemed that the turbo was limited for the rest of the trip. Later in the evening, no more check engine light but I haven't really driven the truck since then.
What do you think the problem was? What should the course of action be?
Having this problem, what to do to correct it? There is no hole in the boot and this just started about a year ago. Does not do it all the time.
View 4 RepliesBought truck for cheaper price with no 3rd gear. Went to a reputable yard and picked up a cheaper trans... It was carfaxed with 185K miles and in a rollover. (This is the last time I try to save a couple bucks by getting a cheaper transmission.)
I believe trans is stuck in 3rd gear...Takes off slow. RPMs do not drop..Doesn't shift...Feels like I'm in 3rd from takeoff. Here are the codes:
P2262: Turbo / Super Charger Boost Pressure Not Detected Mechanical
P2614: Camshaft position signal output circuit / open
P2262 again
P1000 On board diagnostics II Monitor / drive cycle test not complete
P0678 Cylinder 8 glow plug circuit
P0672 cylinder 2 glow plug circuit
P0603 Internal control module keep alive memory malfunction
P0720 output shaft speed sensor circuit
B1676 Battery pack voltage out of range
B1318 Battery voltage low
This may sound petty, but I would like to have the radio controls on the left side of the steering wheel of my 2012, instead of the cruise control. I guess the main question is how the wire harness is set up. Do the wiring can be re-routed to accommodate the switch?
Also, I want to smooth out the ride a tad so as to lessen the amount of griping from from the passenger seat. What is acceptable in lowering the tire pressure to allow a better ride without compromising tire wear? The factory specs are 65 psi. My truck is a 2012 fx4 Lariat with the 6.7
I traded from a 2011 F-250 XLT recently with premium package to a 2015 F-350 Lariat, but the truck we found didn't come with a couple of the features that I loved in my last truck. I live in western Nebraska, and travel very regularly to western North Dakota and central Illinois for my business. The truck has 5200 miles (had the truck for 1 month ), but everything is still in great condition and would hope for the same in return.
View 3 RepliesWeird thing happened today. Was out running errands, and upon pulling out into traffic I felt the truck lag a little. I figured it was the typical trans hiccup we all experience from time to time. As I continue driving, I notice I don't have any turbo boost.
I'm cruising around 55-60 and when I slowly give it gas......No boost. I stomp it and the turbo gauge slowly climbs to about 12 psi. At this point I waiting for the truck to throw a warning message and none came.
As I'm reaching my destination, the speed limit is 30 so I'm just putting along and any acceleration I did, the boost needle wouldn't move. I arrive at the store, and when I got back in 5 minutes later and drove off, My boost was back. Truck operated normal for the 25 minute trip home. I thought a similar thread was started but I couldn't find it.
My truck is all stock and I am running in performance tune? And my friend the former owner said I need to let her loose about 75 percent of the time I am driving it because it's my DD and I do not tow anything on a regular basis. I do not want to stretch my bolts by unnecessary pushing, I don't know if I'm even pushing it hard but I normally get the turbo up to about 30 psi is that to much?
View 8 RepliesStill working on this E450. Now, I'm trying to get the turbo back on and I don't know how the heck to get the oil tube in.
There's so little room that I can't lift the turbo up. Just getting it in and out is a chore. I was able to pull the oil tube out with some difficulty when I was removing the turbo, but if it put it in first, the turbo won't go over it to get back in. If I leave it disconnected to get the turbo in, I have no way to reach under it to get the oil tube back in.
I only messed with it for a little while - it's physically difficult bending over inside the van to wrestle with it - and will go back at it first thing in the morning. I know there's gotta be a way, I've just never done this before.
Do I stick the tube in the turbo first, in the engine, or neither until I got the turbo in place?
I have a 2004 Excursion with the 6.0. Lately it seems like the motor just doesn't have the boost it should. Funny thing is that the boost reading through the edge cts seems to be right. Under full acceleration it will pull 27 psi boost and 3900+ ICP pressure. No codes are being thrown. It just doesn't "feel" right (seat of the pants) and it also sounds louder but I don't known this for sure.
Where does the CTS get its boost reading from? The truck has new boots on the hot side from riffraff. Anything I can check?