Touareg :: Doesn't Pull When Accelerator Pedal Is Flattened?
May 22, 2008
V10 TDI doesnt give any boost when accelerator pedal is flattenned. What could be wrong.
View 2 RepliesV10 TDI doesnt give any boost when accelerator pedal is flattenned. What could be wrong.
View 2 RepliesMy Egg's only a week old and every time i start and get going i get this rattle(and bit of noise) thru the accelerator pedal after a few seconds- just once only and never again until I completely stop and restart to move again.
View 4 RepliesI experience a sound, like a one stroke scrape of a piece of cardboard across sandpaper, after driving off 20/30 feet after starting the T-reg. I discussed this with the VW tech, and he said something about the drive by wire system engages something, and creates the scraping sound, VW thinks this is normal, and there is no fix for this.
What is this scraping sound? The sound happens once and only once every start of a journey, happens even when I am going straight ahead, and at slow speeds (about 20km/hr).
I've taken out the 2 bolt covers, taken out the T30 bolt, and have loosened the gas pedal a bit. But I can't pry the gas pedal upwards with a flat head screwdriver. I'm pulling and yanking this pedal up and back towards the front of the car and it won't pop off! Are there any tricks to getting this pedal off?
View 2 RepliesYou know that low noise you get when you put the car in reverse and the right hand mirror moves downwards. Well I'm getting the same type of noise when I slow down to a crawl and pull the ToeRag in the garage. It lasts for a couple of seconds. Goes away, and then comes back. Also almost sounds like the same "fuel pump priming" noise when the car starts up.
View 7 RepliesIf I'm at part throttle and i press the clutch pedal in about 2-3 inches, leaving the clutch still fully engaged, i can feel a really rough vibration in the clutch pedal. it stops vibrating as soon as i let off the gas. and i'm only giving it a little bit of gas, mind you.
If I'm at idle, and i have the clutch depressed all the way and rev the engine, I can feel vibration in the clutch pedal. My 6-speed MK4 did not do this, not in the slightest. Is this normal for MK6 or do I have a problem?
I'm looking at changing the height of the accelerator pedal so it's more inline with the brake pedal to make heel toe shifting easier, because at the moment I cannot get my heel anywhere near where the accelerator is.
View 3 RepliesYesterday the Check Engine light came on, the code was P1121 Accelerator Pedal Position Sensor Error, Performance/Range. I have not yet had the pedal replaced related to the recall (bad me), is the sensor incorporated in the new assembly or is this separate and I'll need to replace it?
View 19 Replies2000 Integra with 95k miles in an excellent condition - used pedal jack when parked
I had to make a left turn and ramp up so put it on D3 - I pressed the accelerator and when I felt the speed could be higher (I am not comfortable to drive up the hills) so I must have pressed hard on the accelerator. It then responded
Not sure what was happening, I started breaking and steering - still around 30mph, guessing - it was not a wild drive.
Still not satisfied, I moved to gear 2 and stopped the car. Realized the car is still pulling, turned off the engine and realized the accelerator pedal is stuck.
I pulled it and it has been fine! With the engine off, I pushed the pedal hard and it always bounced back. Not sure that the getting in and out the pedal jack had been interferring with the accel pedal. It also looks like the engineers did a good job that with the stuck accel pedal, I did not end up in a wild drive - I had to brake and move the tranny to 2 but was able stop it - it was a mild up the hill, but unsure if it played a big role.
I need to know how to unplug the accelerator wiring. I lift the little red lock on the side, but then I still can't unplug it. I've tried pressing on different places like is so common with other plugs, but no luck.
View 1 RepliesSo I done some routine maintenance on my car today as I have had it just over a month. Done the oil, filter, thermostat and coolant today. This is the 2azfe, 160,000 k's.
As the title suggests, the accelerator pedal has stopped working, but I'm pretty sure its something I have done. I noticed the idle was a bit strange at times when warm, from third to second gear changes the rpm would jump up to around 1200 rpm, but if I changed from 4th to third gear the rpm would drop down to normal idle. So I decided to try clean the throttle body.
I had done this before on our 5sfe's which we no longer have. All I done was disconnected the air intake hose from the throttle body and sprayed some TB/carby cleaner in. On the 5sfe I could run the engine with the intake pipe off and I tried to on this too. It started and quickly stalled. Ok no big deal. So I put it back together and restarted it ok. It run fun. I gave it a few rev's via the engine bay throttle control and it revved ok. I never thought at this stage to check the accelerator peddle itself. Wasn't until the me n the family went to go somewhere I realised I had no throttle. Strangely, with the engine off I noticed the engine bay throttle control seems a bit notchy.
Anyway, tomorrow I'm gonna disconnect the battery to reset the ECU, and check fuses. Could the throttle bottle/carb cleaner have affected a sensor somehow? There was no problem before I done this so I know its self inflicted.
It was the throttle body thing, cleaned that completely. Replaced the pedal with one from the bone yard. No change after clearing codes, the check engine light comes back the second you touch the pedal. Have a new (reman) throttle body coming tomorrow as I may have dinged it up after cleaning it again, I took it apart to see if I could see anything obvious.
Cleaned the carbon tracks inside and bent the brushes up more to contact the tracks better. I doubt it liked that. It was throwing a code for high current, but now that has disappeared. However, I used to be able to rev it up to 2500 rpm, now nada.... So I am left wondering if this is a bad ground or something? Bad wiring to the ECM:?
I would love a schematic showing where any relevant grounds are, pin out voltages etc. It is -15 here. The closest I've come so far: [URL] ....
1996 Jaguar XJ6 4.0 Litre Base, 43000 miles... While driving, this car, suddenly accelerator pedal becomes very hard to push and car will not move at all even if you press hard pedal to the floor( Requires a lots of force). If I put brakes on, shift the transmission to reverse and to then to drive, it will start moving again. No check engine light comes on and there are no codes stored in computer. This never happens on cruise control. Car starts flawlessly even on cold morning. Battery is new and charging system works fine. Spark plugs were changed at 30,000 miles so also direct ignition coil on cylinder No.3 .....
View 3 RepliesThe accelerator pedal on my 1993 Nissan pickup occassionally "sticks". Mainly when I'm leaving a (stop-sign/red light, etc) or if I let off pedal (in traffic etc) then push on it again to accelerate. I've changed the throttle cable (had a brand new one from brother in law...still in packing). I took it to Nissan dealership few years ago and they couldn't figure it out, same with a (highly recommended) local shop.
View 7 RepliesThe Check engine light on my 2006 Prius came on and I used my OBD reader to determine the code was P1121 - "Accelerator pedal position (APP) sensor - range/performance problem". I cleared the code to see if it would register again and a few weeks later same code showed up, but after driving it awhile the check engine light went out with out me clearing it and it remains off. The car drives normally with no other problems and when I monitor the APP sensor output I don't see anything particularly unusual. I can spend the $300 to have a new pedal installed, but I'm not sure there's problem especially if Toyota's design allows for a non-catastrophic failure mode.
My question is how does Toyota's engine control module manage a failure of the APP sensor? Is there a fail safe backup or is there potential for loss of throttle control like we heard about years ago in the news?
Its a 2005 model with 45000 miles on the clock, so low mileage for the year. The problem with it is the engine starts up ready fr a journey, and as soon as the accelerator pedal is pressed, the engine cuts out.
View 7 RepliesMy 2001 Hyundai accent hatchback with around 135000 miles is having problems with the gas pedal. I start my car and can't really push down the gas pedal smoothly. It is initially hard where I have to slightly kick the pedal to move it. Otherwise if I rest my foot on the pedal and try to press it down I end up press it down too much where my car goes flying. Every time I come to a stop I have to do that to get the pedal to move. Its not stiff once I get the pedal to push down some but once I take my foot off the pedal I have to slightly kick it back down.
View 4 Replies2012 Elantra - 105,000 miles 6 speed transmission
Throttle seems to be sticking and causing engine to rev between shifts, and staying slightly on after I let off the gas
Engine continues to rev up uncontrollably for about 10 seconds after feathering the gas pedal (between shifts). If I floor the gas pedal and release it quickly, it closes the throttle and fixes the issue.
Thought it may be a sticky throttle body, sprayed a generous amount of Carb and Choke cleaner into throttle body...did NOT resolve the issue. Its a Drive by wire, so no throttle cable to blame or to clean.
Turns out, the accelerator pedal assembly it self, is not returning/springing back to "up" or closed position and is sticking during the first few degrees of travel. It is very dirty, and gold.
How to clean/lubricate this thing? Its plastic. Or should I just order the replacement? I hope the pedal isn't programmed to the car itself? shouldn't be...but you never know
Just got into my 2006 Sonata V6 this morning. 120,000 miles. Drove last night, no problems. Started her up now this morning, noted check engine light and ESC lights on.
Pushed accelator pedal, no increase in RPMS at all. Put the car in gear (auto), car moves forward and backward, but pressing the pedal doesn't increase the rpms at all, so right now its not driveable. Luckily, its in the driveway so I know it could be worse. Took floor mat out, no interference issue there.
I changed the starter solenoid and that was over 45,000 miles ago. Never had that problem.
I have a Toyota Corolla Altis Cruisetronic Automatic transmission. Car has done only 4000 km and is 8 months old.
Problem I am having is that when I release the accelerator pedal say while driving at 60 kph, the car does not freely coast but decelerates with a drag and tries to slow down to a stop. The drag is more serious with the a/c on. It does not like to remain in high gear. Previous auto transmission Corrolla's I have driven never gave me this kind of problem.
Sometime the car is fighting to move forwards when I start to depress accelerator pedal and it sounds like "click click CLICK..." the sound changes from lower to louder depending on how I depress accelerator pedal... (like the car is trying to hard to move)...
View 3 Replies