Touareg :: Brakes Lost / Pedal Goes All The Way To Floor Board
May 3, 2007
I flushed my brakes this afternoon and all went well until I got in and found a red series of lights on the MFI stating "brake fluid". I touched the brakes and there aren't any. I pumped them 50 times or so and still the pedal goes all the way to the floor board. I used a machine I have used on countless other cars and have never had a problem before. I used VW brake fluid. The brake fluid container is right at the max line. The only thing that was different compared to the other cars I have done is that the Treg has two bleeders, one on the front of the caliper and one on the back. I called a VW service consultant and he told me they use the outside one to flush the brakes and so that is what I did. My only guess is there is air in the system. But, I am not sure at all how that happened.
View 3 Replies
Advertisement
So tonight, I lost most of my brakes. If I kept at low speeds and pressed the pedal to the floor I could eventually stop, but not well. I imagine this might be more of a general question not specific to Ex's, but I thought I would start here.
View 4 Replies
I recently had a leveling kit installed on my 2014 f150 super crew 4wd. When I picked it up, I heard a humming in the front end that ended up being a bad iwe actuator. I took it to the ford dealer and they replaced it. No more humming, but now I have a very annoying vibration in my gas pedal that can also be felt in the floor board and gas pedal. I've had it aligned. I thought it might be my front driveshaft so I put it in neutral while driving and vibration is the same. It gets worse when I get up around 70mph. I also feel small jerks in the gas pedal at these speeds along with the vibration. It vibrates worse under heavy acceleration as well. Cause I can't wait to set my cruise every time I drive it bothers me that much. Only has 10,000 miles on it.
View 3 Replies
Trying to track down a vibration issue. Not steering. But, idling in gear and driving. I feel the vibration through the go pedal and floor board and seat on driver side.
Checked obvious points. Down pipe, complete exhaust system. Motor mounts, tranny mounts and steering.
Got to be some other spot I'm missing. Checked driveshafts. Everything seems OK.
View 5 Replies
I give up. I have been trying for a very long time to get the brakes on my 1936 dodge to work with no results. The whole system is rebuilt, new lines, resleeved and rebuilt wheel cylinders, rebuilt and resleeved master cylinder, no leaks in system, pressure bled, vacuum bled and new lines. I even had a mechanic try and get them to work. He said all they needed were to be bled very slow. he actually got them to work slightly but after the car sat for a week the brakes were gone again. Drums all around, master cylinder is single cylinder. Brake pedal goes right to floor.
View 14 Replies
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
View 3 Replies
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
View 7 Replies
My dad is having problems with his truck, brake pedal goes all the way to the floor even after bleeding all the brakes and the master cylinder. The wheel cylinder didn't have clips in it and he fixed it and it hasnt changed. What do we do? Its a 1993 f150 4.9l.....
View 4 Replies
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 Replies
I did a complete rebuild of my brake system in April. Drums, shoes, wheel cylinders, springs, hoses, pads, rotors, calipers, master cylinder, proportioner valve and flushed all the lines and refilled with synthetic fluid. I have made five trips from Southern California to Idaho hauling home furnishings, one trip to Oregon and one trip to Northern California since overhauling the brakes with everything working great. Now something strange is happening. The brake pedal goes to the floor with very little resistance. It isn't spongy like there is air in the lines. It just goes to the floor if you push it all the way down.
The truck stops ok but it is really scary with the pedal going down like that. You can feel when the rear brakes come on because there is a little resistance in the pedal when they come on. You can actually lock the rear brakes up and skid the rear tires. If you push the pedal down further the front brakes start coming on and if you push all the way to the floor the truck will nosedive and you will get planted in the windshield.
I wonder if the aftermarket Bronco Graveyard proportioner valve is blowing all the pressure to the rear wheels because it won't do it if you take the vacuum off of the vacuum booster. You have full pedal when the booster is deactivated and all the wheels operate normally with the exception of having to plant both feet on the pedal to stop it.
View 14 Replies
yesterday i gave the 02 diesel a treat, 3 new calipers 4 new rotors, and semimetalic pads. the reason for only 3 calipers is the driver side was just replaced 2 months ago after it locked the wheel up on me. both rears were seized so i only had front brakes, and the passenger side front was leaking.
anyway, all new parts and the pedal is fantastic, besides the truck stopping again. this afternoon on the way home from the shop i stopped at a red light. breaks are rock solid. then all of a sudden, the pedal slowly sinks to the floor. but the brakes still hold. i get home and test them. again, pedal slowly sinks to the floor, but they hold. i am thinking still some air in the system, and park hte truck, with the intention of bleeding them again tomorrow.
i get out and see fluid all over the driveway. great. something in the front of the axle is leaking. the frame is drenched. whatever it is, is in front of the frame, on the engine side. what is in there, the ABS unit?
View 3 Replies
I have a 2008 GC with the E-Brake calipers in the back. I changed the brakes and rotors all around and now the petal goes to the floor. I know it has something to do with the rear brakes, because I did the fronts first and after a few pumps I had good petal.
I've done these types of rear brakes before, you use a tool to turn the caliper in. Is there anything I missed? Did I turn it in too much? I don't think it is the master cylinder because it was fine before I started and fine after I did the fronts.
Also, the e-brake doesn't hold at all now, so that's another reason I think the problem is in the rear calipers. Maybe an Adjustment? There's nothing leaking, either.
View 5 Replies
I have a 2002 Honda Civic EX 1.7L. Recently the brake pedal would sometimes go to the floor when I'd apply the brakes. The car would still stop, but not as quickly as normally. If I apply the brake and it goes to the floor I would release the pedal and reapply the brake and it would stop at it's normal position and the brakes felt firm and the car would stop fine. I was told my problem was the master cylinder so I bought one on Sunday and replaced it. I bled the lines and it seemed like all the air was out. The brakes worked great and the pedal stopped in the same place and was firm.
Now today on my way to work the pedal went down a little farther than normal during one stop. On the way home it stopped in different places. The brakes would always grab and the pedal felt fairly firm wherever it stopped. I drove it this evening again and the pedal went to the floor like with the old master cylinder. One pump and they grabbed in the normal spot. What is going on? Did I not bleed the lines well enough? Is the new master cylinder just junk? I saw in the manual that air can get trapped in the ABS sensor, but an air bubble problem should just make the pedal squishy, not change where it grabs, right? I'm stumped and I really don't want to take my car in if I can fix it.
View 6 Replies
I have replaced the front rotors, calibers, pads and brake lines. I went through the process of bleeding the brakes by using the following sequence: right rear, left rear, right front and left front.
I did this about 4 times - process was to pump the break until the pedal was hard then my son kept his foot on the pedal while I release the bleeder value. During this process I kept the master cylinder full.
Took the car out and the pedal went right to the floor when applying the brakes. The car did stop but not as I had expected. So what have I done incorrectly here? Is there something else to check?
View 3 Replies
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 Replies
My problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 Replies
I've got a 2001 Excursion with the 7.3 and while out driving around on Friday I noticed that my brakes were gone and when I pushed the pedal it went straight to the floor. I pulled over and put in brake fluid (it was empty) and managed to get home. I have discovered that the brake line (it is metal) that runs from the front to the back is rusted out and the brake fluid is just pouring out of it. What is the part called? I spent about a half hour looking for that particular schematic on the ford parts web site but couldn't find any mention of that brake line. Here is a picture. There are 3 metal lines and one is leaking the brake fluid? Can I fix it in my driveway or should I have it towed somewhere?
View 4 Replies
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 Replies
So the other day I slammed on the brakes when traffic came to a halt on the highway. As I slammed down on the pedal, all the sudden the pedal lost pressure and went nearly to the floor, but firmed up just before bottoming out. My brake and ABS lights went on as well. Someone told me there is some kind of failsafe that blocks off the line if it ruptures, so maybe thats what happened? The brakes seem to work fine and are not loosing any more fluid, but the warning lights remain and the taillights do not light up.
So when I got home I took a look. On the fender side under the fuse box there was a lot of brake fluid, and looked like the line going from the master cylinder down to some kind of module (abs thingy?) below it was all rusted.
Today I replaced the line, and bleed the rear brakes. There did appear to be a ponhole in it, right where it would have been spraying the fender side where I saw all the fluid. The pedal is very firm right from the get go and brakes seem to be working fine. However the brake and ABS light remain, and my brake lights still dont come on when I press the pedal. Do I still have a leak somewhere or is there something else I have to do to clear the warnings and get my lights back?
View 11 Replies
I have a 2003 Ford Escape 3.0l V-6. In June while driving to a job interview, my brakes unexpectedly failed. With absolutely no warning, the pedal went straight to the floor. I replaced the master cylinder...problem solved. 5 months later, driving to the gym, after stopping successfully several times with no mushiness in the pedal, at an intersection, the pedal goes straight to the floor...no stopping power.
I can't remember if the brake light came on last time. This time it did. Both times the fluid in the reservoir was full and looked to be relatively clean. Both times there were no apparent leaks in any of the fuel lines, abs module, at the cylinder, etc. I'm no slouch when it comes to car repair. The master cylinder replacement was done correctly, the lines were bled properly.
I have my own theories but I don't like any of them as my car rolls properly at idle, my brakes have not, nor do they currently make any noise or grinding sounds, and the pedal goes all the way to the floor.
View 8 Replies
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cylinder need rebuilding or is my vacuum diaphragm going. Not sure that's what its called.
View 7 Replies
