I have had my 06 for 4 months now. I started to get a cold running problem now that the temperature is falling below 40. When I start it in the morning I wait till the idle comes down before driving. I start driving and it runs rough as if it had a choke stuck closed. I spoke with the dealer and he told me to run lower octane in the winter. That has not worked.
View 7 Replies1979 ford f-150, 460 w/ 4bbl. Carb recently rebuilt by professional, but on cold mornings (in particular) runs rough even after a little warm (just like me), like the choke isn't clicked or clacked (couldn't resist) off. Can the choke flap and mechanism be gunked up, needs some cleaner applied?
View 2 RepliesI have a 98 Grand Cherokee (V-8) with 127K on it, that sometimes during cold starts acts like an old carburetor system with the choke sticking. It floods, chokes, it sputters, and you have to maintain an RPM of about 2000 to keep it running and get it to snap out of it. A local shop did a tune up on it before this problem started to happen intermittently, aside from this, it seems to run well. I took it back to the shop and they did several diagnostic tests and even got it to do it for them while they had it.
I told them that it seemed like if we released the key from the start position as soon as it began to fire, the problem would happen, if we held it I the start for a bit longer we could usually avoid it. They returned it to me saying that "Yup, if you hold the start position longer it won't happen, and by the way here is a bill for $103." With the recent below zero temps, it's getting worse, almost unavoidable. My wife says it uses a lot of fuel when this is happening but we have not actually tracked the mileage. Other than this it's a great car but I'm ready to drive it off a high mountain cliff.
My truck is a 1995 Explorer 4.0 150,000 miles, 5 speed.
Problem - Rough idle : when cold it's worse and will stall and choke a little. When warmed up it just has a rough idle but will not stall and stays at a pretty constant RPM. It's very tolerable when warmed up but still not right. It drives fine once off idle. No black smoke that I can see. Power may be just a little off but I would not bet on it. MPG seems about normal but haven't been on a long enough trip since problem started to tell for sure. Also longer than normal cranking on occasion.
Diagnostics so far : Fuel pressure is at 32 PSI, vacuum off regulator it's at 40 PSI. Not sure about key on only as I don't trust the autozone loaner gauges. You have to fiddle with it each time before it will read. Leak down after 30 minutes was about 4 PSI
No Check engine light ever. KOEO test shows no hard or on demand codes, I get the 111 pass. From CM I get 336 and 45.
336 is EGR related and my looks pretty rusty. I put a vacuum pump on it while running and the EGR held vacuum but had no effect at all on idle, I was expecting it to get worse as I opened the EGR so it may be stuck.
Searched high and low for vacuum leaks by ear, visual and with starting fluid all turned up nothing.
Actions so far : Replaced plugs, wires, IAC, and fuel filter. Cleaned MAF sensor and throttle body plus ran lucas fuel injector cleaner through it.
Next steps : I've got the EGR but it's so rusty I am sure I'll break the tube it bolts to plus I don't know it that alone will cause the rough idle. Will the DPFE sensor and/or EVR create a rough idle yet not turn on the CEL?
Thought about changing the fuel pump and/or regulator but the numbers are not terrible. Agree?
Thought about changing the intake gaskets but don't see any leaks.
My thermostat is stuck closed so it needs replacing. I searched and couldn't find a DIY but there was a thread that says you need to take the whole front end off?
View 8 RepliesMy 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 RepliesWe have a 2007 Hyundai Sonata Limited Edition. The problem started when the rear diver side door window stopped working. we took apart the door and saw that the cable was all twisted. We found the part at a junkyard and replaced it. Window worked. We closed the door and didn't think twice. A few hours later we tried to open the door and it's stuck. Both inside and outside handles move but nothing happens. The door won't open at all, what to do. We obviously can't get the door off without it opening. What may be causing this??
View 2 RepliesI have a 1993 Audi 100s 2.8L V6It needs new spark plug wires for sure. However recently when I start it up it has been blowing white smoke out the tail pipe and runs really rough. However once I run her for a while smoke goes away even when heavily accelerating. Also when It runs rough I can smell raw gas. Whats going on to my car?
View 8 RepliesAbout 2 weeks ago my 1997 Buick Park Ave (115,000 miles) began running bad during a heavy rain storm. It was running fine. Then all of a sudden at a stop light the motor hesitated and wanted to stall. I nursed the gas peddle and limped home and turned the car off. The car hesitated and sputtered all the way home as if I was running out of gas.The next day the car would not start. It turned over but would not start. I tried starting the car for three days. My mechanic friend later diagnosed the car and stated the computer was not functioning correctly. He replaced the computer. The new computer seemed to correct the problem.
The car ran great for the next 2 weeks. Yesterday, it was raining hard while I drove the car about 150 miles without any problem. Then suddenly again the motor started running badly. Again, the motor wanted to stall and hesitate as if I was running out of gas. I limped home again. This morning I tried to start the car without any luck. In addition to installing a new computer, In the last 2 months I have changed all the fuel injectors and installed new spark plugs.I have also changed the fuel pump and repaired the fuel tank. My mechanic say the cam sensor and crank sensor are operating correctly. There is spark coming from the coil packs and to the spark plugs. I do not want to randomly change parts.
2000 Toyota Camry le v6 .... When I first start my car it runs rough after about 5 to 10 minutes it runs fine. I have no check engine light on. I used sea foam and the problem went away for a couple weeks then it came back. I have about 30k on my spark plugs.
View 10 RepliesMy V6 3.2l runs very rough for 1-2 minutes at startup when cold i.e. the first startup of the day, or after it has not been driven for several hours. Is this normal? I understand this might be something to do with the 'anti-knocking' feature. But I only use RON 98. Also I can here something like a tappet sticking when idle all the time. Is this normal, is it just a noisy engine design? The car has only done 1800kms.
View 2 RepliesI have a 2005 Chevy Equinox with 73K miles. When I first start it up morning the car runs rough for about a minute or two and then smooths out. I took it to a mechanic who said there was oil on one of the plugs and to get rid of the car. I tried another mechanic on Craigslist and he replaced the upper plenum gaskets. It ran better for about a day or two and now the problem has resurfaced.
View 2 RepliesThe car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 RepliesI recently replaced the plugs cuz I had a rough idle all the time. During plug change when I discovered they had already been changed I found one that had a burned off electrode. Does this mean a lean condition exists?
After plug change it runs smoothly but only after 10 min warmup in our canadian winters. I can drive it when its not warm but seems to have less than full power and idles very badly after driving w/o proper warmup.
Next I changed fuel filter and checked fpdm, it was a little rusty but not bad so i just mounted it 1/4 off steel to prevent further rusting.
Since then I have installed a programmer [diablosport] but found no codes since i had battery disconnected for filter change. no new codes in last few weeks since.
So do I have a lean running cylinder causing this poor cold idle or a rich cylinder? It must be a clogged or dripping fuel injector right?
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 RepliesI have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesEver since I picked up my V8 Touareg I've noticed that the transition from stopped to starting can sometimes be rough, and that the shift from 1st to 2nd is often a fairly violent jerk. The worst transmission problem on my Touareg is experienced when I'm in stop-and-go traffic going around 5mpg in 1st gear then accelerate normally. The shift to 2nd is extremely rough.
I took my Touareg into the shop last week to fix this, and another problem I was having, and the car is still at the dealer. When I talked to my service advisor on Friday he said that this is a fairly common problem with later VIN cars. Evidently, they had to reprogram the transmission to meet some EPA regulation and that is causing rough shifting in the lower gears.