Just started hearing a thumping/ rubbing sound when I make left turns (nothing moving forward or right turns). Thought it might be a tire rubbing but I can't see anything. Starting to think maybe a bad cv joint. Is their a way to check if a cv joint is bad? How hard would it be to replace a cv joint and shaft?
View 3 RepliesBefore I take my 3 month old T2 in for service AGAIN this Saturday. The more informed I am when I walk up to the service counter, the better.
When I make a hard left turn (more than 90 degrees), I now hear a sound from the front left wheel area. It sounds sort of like the sound a plane makes when flying overhead. It's sort of like something is rubbing.
This started all of a sudden last Thursday. I thought it would go away. It doesn't sound normal and it doesn't happen when I turn right. It doesn't affect my steering. I don't recall hitting anything (note I sait recall).
Obviously, I got out of the truck and examined the entire area but I don't see anything unusual. I drove around in circles with my head out the window trying to figure this out.
Back in January I had my right front wheel bearing and u-joint go out, so I replaced them both. At the time I didn't realize my outer stub axle shaft was wore so I just put it back in. After a little driving the right side started to "thump" and "pop" when I would make hard left turns driving around town.
I replaced the outer front stub axle shaft and seal again because the old one was worn down. This eliminated any play in the u-joint. After a bit of driving the thumping and popping noise came back.
I decided to dig into it today so I pulled it all apart. When everything is apart it turns easily, no issue at all. When I assembled the wheel bearing, torqued it to 55 ft/lbs and installed and "locked" the hub I noticed something peculiar. I can barely turn the whole assembly by hand. I have to put a good amount of force to get the whole assembly to turn at all. When I walk to the driver side with all the same parts there i can turn the wheel bearing and locked axle shaft with one finger on the studs.
I have been in this thing 5 times and can not figure out what the heck is wrong. I can't figure out why this stupid axle shaft and wheel bearing are so hard to turn, together or separately, and I can't figure out how to get my front end to stop that thumping and popping.
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
My 04 gli makes a rubbing noise when accelerating thru hard left turns.. but weird enough i can take the same turn at the same speed in neutral and have no noise at all. I changed both front wheel bearings and cant seem to find the answer. I brought it to vw and they checked the whole suspension struts springs cv's tie rods ect. and they all checked out good they said. the car used to have a exhaust and i just recently put it back to stock, could the exhaust make the noise perhaps?
View 1 RepliesI have a 2002 Subaru Impreza Outback Sport. There is a slight rubbing noise when I make wide turns and I suspect it is the wheel bearings. How much should it cost to replace these, and how thin is the ice I am skating on if I put it off?
View 4 RepliesI have a 2005 Saturn Ion stalls when I make left hand turns! The engine light comes on and the car goes into limp mode! I stop the car and wait a minute or two and it starts right back up and after driving it for a while the engine light goes out! I took it to a shop and they replaced the throttle body and ignition coil on two different occasions and my car still does the same thing!
View 2 RepliesHave a problem When i make a slight turn to the left sounds like the tire is rubbing the inner fender. Don't do it all the time. The tire is not rubbing.
View 4 RepliesI have an 08 AWD GS350 ...
For the last few months, it has been squeaking whenever I make hard left turns, (into parking spaces etc, usually low speed). I thought it was the brakes, but just replaced all 4 pads and all 4 rotors. So that officially eliminates that.
The car doesn't have any unusual vibration, tracks straight, so I don't think its a wheel bearing or anything. I jacked the car up and tried to shake the tire/wheel to see if there was any play but don't see anything.
I have a 2006 GMC Yukon XL 4WD 1500 with 95,000 miles. When I make left turns, after coming to a stop, the antilock brake system engages, making a groaning-pumping sort of sound in the upper front left area under the hood. (This does not happen every time I turn after stops, but frequently.) My local GMC dealer mechanic believes that there is a faulty wheel bearing, and that a signal is being sent to the antilock brake system to engage. Not sure whether I should believe that or not. The repair would be expensive.
View 4 RepliesWell my girls car is acting up again. when you make left turns, you can hear this real loud popping, almost cracking noise coming from the passenger side front tire. its a 06 passat with 88k miles on it. What is wrong with it??
View 4 RepliesI have a 2010 Honda Civic with about 32K miles on it. Last fall, at around 23K miles, I needed new brake pads and rotors (because I waited too long on the pads). Got those replaced. A few weeks later (I think), it started making a kind of squealing noise when I make left turns. I mentioned it to my mechanic when I took it in for an oil change shortly thereafter, and he said it was probably the belt, but I could wait a bit on replacing it if I wanted to (as he knows I'm always broke).
Three weeks ago, I took the car in for another oil change and to have him change the belt. He put in a new belt, but alas, after driving the car about a mile the noise returned. I called my mechanic, and he said it might be my tensioner, but that such a new tensioner shouldn't need replacing already and that it would still be under warranty. I needed to take it to the dealer anyway because my window mechanism was broken, so while I was there, I had him check out the tensioner. He also said the tensioner was fine, and said that since the belt wasn't a HONDA belt (naturally), that might be making the noise. Last week, I took the car back to the mechanic, who ordered and installed a Honda factory belt free of charge.
Naturally, a mile later, the noise returned. I resisted every urge to drive into oncoming traffic. I used my phone to record the sound so that I could e-mail it to the dealer and my mechanic, give it a listen: [URL] ....
My 79 year old father put fuel additive in his 2010 Chevy Impala. Don't ask me how much, or for how long... The Check Engine light came on. I never got a clear answer from him on what his mechanic said about it. Five to Ten fill ups later the Check Engine light went out on its own. Engine seems fine. Could this have caused damage to the engine or emissions controls? Would a computer diagnostic from a mechanic pinpoint any problems? Would you recommend a computer diagnostic be performed?
View 6 Replies2013 SF Limited AWD = long base, 41K miles
Slow speed sharp turns left and right taking off from a stop I hear a thumping/light popping in the driveline. Seems like it could be a differential issue?
I also hear an unusual noise while accelerating in a straight line.....under throttle from a stop, it sounds like a rapid chirp on and off, every other second. Almost like a valve tick. The noise is heard under acceleration in gear, not when cruising at light throttle. I put the transmission in neutral while rolling, revved up the engine and the noise is not heard. Only happens when in gear and accelerating.
Due to the clicking-ratcheting sound my 1997 Civic makes when I make hard turns or U turns, two mechanics (one drove the car) say that I need two new front axles at a cost of $400 ($200 each). I have driven the car like this for maybe a couple thousand miles before I looking into it. How much longer can I drive it like this before it gets dangerous or fails? I now only make gentle turns and so minimize the clicking-ratcheting sounds that happen only on hard or aggressive turns. The car only has 76,000 miles on it. Is it dangerous to keep driving it?
View 7 RepliesSo yesterday i just noticed a ticking sound (drivers side, almost sounds like its coming from from under my drivers seat underneath the car) when i make sharper turns, but it wont tick when i make regular turns or go around corners.
I lowered my car about 5 or 6 months ago on Tein S Tech 9th gen springs, could that have caused whatever this ticking sound is to start ?
2010 Corolla
I had my local race shop install my new PPE headers and how I have a rubbing and grinding sound while taking right turns. They have had the car for a few extra days and they say they cant seem to find the cause of the problem. It rattles on a pot hole, it grinds on right turns and sometimes vibrates on highway cruise control driving.
View 14 RepliesI have a 2009 Camry that makes a metal to metal rubbing noise when turning left. t is coming from the Front Right passenger side. I recently changed out the bearing and hub on the front right but I still have the noise when turning left. Also, when driving normally and going straight there seems to be somewhat of a dull click click click noise.
View 3 RepliesWhen I turn left sharply i hear a rubbing sound. I thought it was just tire rubbing but I am not sure. What else could it be? The car is stock height stock everything. It just got new brakes and tires recently. it looks like something is rubbing the cv boot....
View 5 RepliesWhen i make a left turn i can hear a rubbing sound thats like a low groan. Searched it but couldn't really find one that was described this way. It's a 20th GTI.
View 22 RepliesSo I've been driving my 3GS 350 and every time i make a right turn the left wheel makes this metal shaking sound? or scraping sound? I've checked it out seems like nothings in the way but I don't know how to tell if i have a bad wheel bearing..
View 9 Replies