Tiguan :: Code P2015 - How To Replace Entire Manifold
Apr 10, 2016
Had a P2015 code today on my 2009 Tiguan. Does this mean I have to replace the entire manifold ?
View 6 Replies
Apr 10, 2016
Advertisement
Tiguan :: CEL On - P2015 Intake Manifold Runner Position Switch Code
I have a 2011 Tiguan S 4Motion with just over 63k Miles which for the most part has been problem free and great to drive since I leased it at 40k miles. About 2 weeks ago my CEL came on and I used the Torque app on my phone to check the code and it was the apparently well known P2015 intake manifold runner position switch code. The car was running perfectly fine so I cleared the code and it stayed off for about a week before coming back on with the same fault again yesterday. I have a couple of questions for the much more knowledgeable than I people in this forum around this code.
First - I've read in several places that VW has placed an extended warranty on the manifold and fuel injectors for the 2.0 TSI and that this code is usually an indicator that the manifold needs to be replaced under this warranty. What I haven't found though is conclusive info on is whether the 2.0T in my 2011 Tiguan is covered under this extended warranty. Since this code so conveniently is popping up just 3k miles past the end of my 60K mark, I'd like to know this. I leased the car from Enterprise, not a dealer so I'm worried that whatever dealer I take it too will try to bend me over on the service so the knowledge that the manifold is still covered would be at least some comfort.
Second - I won't be able to get it in to a service department until mid next week and I have a 300 mile trip to make this weekend. The car is driving fine as far as I can tell so I'm not overly concerned. I do my own basic maintenance i.e. oil changes, plugs/coil packs etc. but I'm thinking changing the manifold would be a little bit out of my comfort zone..
Golf/GTI VI :: CEL Code P2015 - Intake Manifold Bad
My husband has a 2011 GTI, which has just hit the 40k mileage mark. His CEL started coming on in March, but we figured it was due to him not tightening the gas cap enough, as he'd open and relock the gas cap, and the CEL would go away within a few restarts of the car. Took it into the stealership last week, got the 40k service (which was a bit of a rip-off in itself), and then got told the manifold was bad.
This is the exact text for the invoice: "Checked the vehicle for codes and found code P2015. Traced the intermittent failure to the intake manifold valve flap sensor failing."
I've seen a lot of posts around this problem, for many models and years, but it seems like most people managed to get it repaired under warranty / TSB. So I have three questions:
1. In the OBD codes, does it store date as well as code? In other words, is there a way to prove that this failed under 36k miles?
2. What's the process for getting this escalated to VWOA customer care, since I feel this should be taken care of under warranty?
3. The dealership we took the car to (which is not where we purchased the car, but is just closer to home) was shady, and the guy we worked with was, to say it nicely, a jerk.
Golf/GTI VI :: 2011 - Got CEL And Error Code P2015?
Soild CEL, autozone pulled a P2015 code, but couldnt find it for VW in their system, just hyundai, toyota, dodge, and kia codes came up.
Looked around and everywhere says it's the notorious MKVI IM replacement issue.. Im under PT warranty until Nov. '15 so im good there.
Heres the catch.. sometimes it goes off without any changes to the vehicle. First thing (before the obd2 reader from autozone) i checked was my gas cap, that will cause a CEL sometimes, next time I started the car the CEL was off. the next day, without touching the gas cap since, the CEL was on again, today its off
car idles fine, drives fine, MPG are fine, pulls fine, stops fine, steers fine, everything works in the car. year: 2011
Ford 6.0L Power Stroke Diesel :: 2007 - Leak Near Hydroboost - Replace Entire Part?
So I take my new (for me but used) 2007 F350 to the local Ford Dealer to have the oil changed, along with fuel and water separator filters. I even added some Archoil 9100 since it treated my 03 so well. Since I had no history of the last change I wanted to do it right away.
While its on the lift he notices a leak near the hydroboost. I think there on crack...but that's my opinion.
Anyways I look at it and I see a leak at one of the connections under the Master Cyl. Its the connection closest to the firewall. My question is there a oring in there that can be replaced or will I need to replace the entire part?
Golf/GTI VI :: CEL Code P2015 / Flap Motor Not Working Correctly
I got the known p2015 code about a month ago and the CEL is on. Here is my situation though...I went and had my car tuned for an APR stage 1+ tune with stock hardware, everything was fine. I then upgraded to a catless 3 inch downpipe (ebay on that links up to the stock downpipe) and a short ram intake and decided to go to the 2+ to delete the engine code for not having a cat.
While I was there, the guy tuning my car said on top of the code for not having a cat, there was a code for my intake manifold saying that one of the motors for a flap wasn't working correctly. I left there expecting to see a code but it never came back on. After4-5 months, I had to pass emissions. Obviously you cant pass with the 2+(found that out the hard way) so I had to have it returned to a regular stage 1 with the stock downpipe. Still no sign of a code for the intake manifold.
I passed emissions and then put my downpipe back on, however, I decided to buy the 200 cell cat from 42DD to weld into my downpipe to save me from having to constantly get my car tuned just to pass emissions. After welding in the cat, I still had a CEL. I went to advance auto and it said I had a code p2015 Intake Manifold Runner Sen Sw Ckit Rng/Perf B1.
I went and got my car tuned to the stage 2 for the hi flow cat and the light is still on. My question is, do I need to replace the whole intake manifold or is there a possibility that I could replace just a sensor? I have a 2012. If just replacing the intake manifold will solve this issue, I'll probably just buy [URL] .... and replace it myself (assumable that's what I need ).
Tiguan :: CEL Came On - Intake Manifold Sensor
Today I was on my way back home from a weekend trip to see family when the CEL came on. The car was running fine no problems (we had driven 200 miles). Gas mileage was good, good power, no weird noises, engine temp was fine (it was 100 degrees outside). But being how the car has 39k on it and its the most expensive thing I own; I pulled over and had autozone scan it for me. It came up as Intake Manifold Sensor. I have never worked on this car but Im going to at some point, I'll replace it myself if it isn't to hard. I am wondering if it is as simple as replacing the sensor or could there be an underlying issue like a blown intake manifold gasket (like i said the car was running fine though)?
View 6 RepliesFord F-150 (2004-2008) :: 4.6L - Remove Manifold To Replace Gaskets For Crossover?
I have a leak between the metal and the plastic of my water crossover.
Do I need to remove the manifold to replace the gaskets for the crossover and if so looking for a good thread showing how.
Tiguan :: Intake Manifold Failure - CEL Flashing / Rough Idle
Well my 39000 mile run of zero faults ended with a intake manifold failure. The check engine light came on whilst on a Yosemite trip, I checked fluids, etc, car was driving ok, but when I reached my destination I noticed a rough idle. Next time I started it a couple of days later the check engine light was flashing, and it was a rougher idle, so I knew enough not to drive it.
The closest dealer fixed it (no cost to me) under the power-train warranty (nice customer care from Michaels Fresno plus they had the parts in stock).
I learned a couple of things being stranded:
1) Problems happen but they can be accurately diagnosed and fixed.
2) $150 coverage for towing on my insurance policy doesn't get you very far. But I wanted to take it to VW to simplify any warranty work and have it repaired quickly, so I paid quite a bit of overage.
3) Tow trucks don't carry a family of 4, so the logistics of getting a rental car to get my family home wasn't simple.
4) If you have to be stranded, Yosemite valley with the free shuttles, is a pleasant place to be.
5) If you need a reminder just how good a car the Tig is to drive, just try renting a Jeep Compass for few days...
Diags for the record:
GFF found 9 faults: P0170, P0300, P0301, P0302, P0303, P0304, P0507, P068A, P2015. Found arm for intake runner flap came apart causing vacuum leak that caused engine misfires.
Parts
1 x 06J-133-201-AS Manifold
4 x 06J-998-907-B Repair Kit
Ford Super Duty (1999-2016) :: 2002 F250 - Replace The Intake Manifold Gasket?
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesPrius (2010-12) :: Check Engine Light / Code PO0456 - Entire Gas Tank Needs To Be Replaced
2012 Prius Gen III 38,000 miles, check engine light came on. Drove car to dealer and they came up with error code 0456. The explained that a rodent (I live in a rural area) chewed on a hose which is causing a leak like a bad fuel cap.
To solve this problem they recommend that the entire gas tank needs to be replaced. Does this seem reasonable? It seems to me they are saying that the chewed hose can not be replaced.
Tiguan :: 2012 - Way To Replace Speaker?
Having speaker replacement on Tiguans lately? I have a 2012 SE RNS315 without the Dynaudio system and find it to be OK, but the midrange and highs are just lacking at least to my ear.
I dont really want to do a headunit replacement, just replace the speakers in the front and rear doors if possible.
Tiguan :: Lack Of Power Under WOL - Replace Cylinder 4 Coil Pack?
So, we have a CEL and we're experiencing the lack of power under WOL. Feels like the fuel is being shut off. Did a little research and I guess the computer sees the issue and will cut fuel if it recognizes an issue? Could be the reason its showing the "Fuel level too low"?
Vagcom shows as follows:
2 Faults Found:
000772 - Cylinder 4
P0304 - 000 - Misfire Detected - Intermittent - MIL ON
Freeze Frame:
Fault Status: 10100000
[Code] ....
My plan is to replace cylinder 4 coil pack and all the plugs.
Tiguan :: 2011 - Tail Lights Lens Broken / Replace Whole Assembly?
Last night I broke the tail light at the grocery store... I came out and there was a line of carts behind my car that a parking lot attendant was collecting. I added my cart to the end and went to shove them all out of the way, and he yells to me, "I got it! I got it!" so I leave them, get into my car, see him go past with a bunch of carts & back up. What this will run? Can I just replace the lens or do I have to replace the whole assembly? And is this something I can easily enough swap out myself?
View 2 RepliesTiguan :: 2013 - How To Replace Factory Low Beam Projector Style Headlight Bulb
I have searched high and low, and I cannot find how to replace the factory low beam projector style headlight bulb on my wife's 2013 Tiguan SEL. It came with the factory LED style HID lights. There were a ton of videos and how to's for the regular Tiguan headlight replacement, and for aftermarket Ebay LED ones, but I can find anything about how to replace the factory low beam projector bulb, other than "take it to a dealer". My thinking is 'if the dealer can do it, so can I'! There has got to be a way. I can't get the wire bulb retainer loose, or get the bulb out of the headlight housing.
View 2 RepliesPassat (B6) :: Replaced Intake Manifold But P0016 Code Still Remaining
Some technical issues here. Had the intake manifold replaced under extended warranty ('09 2.0 TSI, 115,000km); they cleaned out the carbon as well. There were all sorts of codes it was throwing, despite having new coils and plugs installed.
One more thing to do. I still have Crank Position Sensor code showing. Car runs fine (much better now actually),but I was told if I don't get this last code looked after, one day the car just won't start.
Prius (2001-03) :: Engine Runs Then Stalls / P3191 Code - Oil In Intake Manifold?
Looking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.
View 14 RepliesFord - Windstar :: 1998 - Code P1538 For Intake Manifold Runner Control
I have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?
View 14 RepliesFord 6.7L Power Stroke Diesel :: CEL With Code P2074 - Cracked Intake Manifold?
I was chasing down a P2074 CEL and thought it was a stressed wiring harness connection on the MAF.
Took it to the Ford house and they chased it for 2 days, believing it was the MAF and air filter. They told me that air filter was allowing to much air in. My thoughts was, that is was what MAF is for, to regulate the fuel based on how much air was going in.
I just found out that they are stating that an AFE dry air filter contributed to a cracked intake manifold because the aftermarket air filter made the intake get too hot.
Passat (B6) :: Codes P2015 And P2008, Car Started Idling A Little Off
Last week my wife's passat started idling a little off and then the check engine came on. So I connected my scanner to the car (not VAG-COM) and the two codes that were stored were P2015 and P2008. From what I can find online it has something to do with the flapper motor but the description of each code is:
P2015 - Intake manifold runner position
P2008 - Intake manifold runner control circuit
Sonata I45 (LF 2015+) :: Code P2006 Intake Manifold Runner Control Stuck On Closed
Check Engine Code P2006 intake manifold runner control stuck on closed? Taking it in to have it checked out.
View 10 Replies