In my 97 Ford Taurus the turn signals and hazards are not working. I changed the fuses, but still no luck. Someone mentioned that there might be another fuse box under the hood (besides the maxi fuse box). Also someone mentioned the blinker fluid being low.
View 14 RepliesI used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 RepliesI've driven home from a tree nursery with a utility trailer - hazards on at about 60kph. Took me about twenty minutes to get home. It's a pretty warm day so AC was on. I turned the hazards off to signal turns and then put it back on when it was straight road.
After disconnecting the trailer and later driving to pick up the kids, I noticed the turn signals wouldn't blink but the hazards would still work. The AC would not respond, nor would any of the climate control buttons. The heated seat controls are dead and also the 12V DC outlet next to the seat switches seems to be dead. However, the airbag compressor control still functions normally, the diff lock button still works fine, the headlights and hi-beams still work as well.
I took a few minutes when I reached the first school to check through the fuse box under the hood but there wasn't anything obvious. I'm also considering just removing the negative on the battery to reset the computer. Then, there' s the window thing....
I drive a 98 Ford Contour Sport. When I was driving today, I signaled a left turn, and the signal began working erratically. This also happened with a right turn, and, since I deliver sandwiches, happened when I turned my hazards on. Throughout the day it got worse, and eventually stopped working. I'm willing to bet that it's a wiring issue since all of my fuses are fine.
View 5 RepliesWell, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 Replies2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
I recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?
View 14 RepliesI have had this problem for a while now, but can't seem to figure it out. I'm sure it's an electrical issue, but I'm not that great with electrical. My turn signals don't click when I push the handle in either direction. The turn signals come on and stay on but don't blink like they should. I checked the lights in the front and back and they just stay on but don't blink. Also my hazards don't blink. They just stay on and don't make clicking noise either. My horn doesn't work and my door doesn't ding with the key still in the ignition but in the off position. I don't know of it's all related or different issues.
View 10 RepliesI have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 RepliesDad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 Replies2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesEvery time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
The back turn signals on my 93 ford taurus wont work but the front ones do. i checked the fuses and the bulbs and everything was good. the brake lights work and the head lights but no turn signals. same with the hazard lights. front ones work but no back ones. what should i try?
View 1 RepliesWell now I have to replace the multi function switch due to moving my steering wheel and the headlights sometimes working and turning signals not working. I saw a great video on youtube about changing a Multi Function Switch and it shows where the air bag needs to be removed. I was hoping that since my truck is an older 1997 F250 LD I wouldn't have to remove the airbag. Is there a way to do this w/out messing with the airbag on the 1997?
View 1 RepliesComing back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 RepliesA month ago, I needed my horn. No workie. Blown fuse. Yesterday, drove all morning, everything fine. Parked, came back to car, no signal lights on either side, no emergency flasher. Pulled fuse covers, no blown fuses. Restarted car, signals working again. Another change also: Ever since I found out how to view total consumption, miles since fillup, etc on the MFI, I have been unable to change it to current stats. I've pushed the roller wheel over and over again, held it in, etc. Now that this electrical gremlin has reared its ugly head, my trip computer has, on its own, reverted to current readings.
View 4 RepliesSo I get to explore my first repair with this new to me car. Yesterday morning, turn signals works fine. That afternoon, the stalk apparently stopped working, which I have heard of. Interestingly though:
-the brights and cruise work
-the hazards work (my improvised indication that I'm turning )
-the stalk had been replaced once before by the PO.
Did this thing eat another stalk, or are there some other things I should check first?
I just noticed this driving home tonight and I have no idea when they stopped working. I have a few guesses.
1 : I installed puddle lamps and either didn't plug something in OR when they were coded something went wrong.
2 : I have colored side markers with no bulbs and they are somehow connected.