The middle sliding seat has jammed and I cannot get it back into the regular sitting position. I don't see any obvious obstructions, but there are a couple of springs not attached, and I may be missing a connecting rod.
Any pictures of how a "normal" mechanism should look like?
Any trick? I folded down the larger (driver's side) middle seat to get a large payload in...now it won't pop back up...no matter how much lever pushing and seat-yanking I do. It's a 2001 Limited.
View 14 RepliesThe headrest of back seat will bend over when fold down the seat. But one of the headrests can't go back to original up position. The dealer has adjusted the cable but this just temporarily fixed the problem. The problem is back again. I will go back to dealer but can they really fix it? Should I ask for a replacement of the whole seat?
View 1 RepliesMy driver seat has started moving on its own, sliding back and reclining. 1 have a 2008 Azera, 45,000 mi
View 4 RepliesI have a '10 IV and my drivers seat clicks in the middle of my back. It seems that it may be the top of the lumbar cushion going bad.
View 10 RepliesI am having a problem with my rental passat, its a 2013 with 860miles and the seat lever that makes the seat recline broke and now the seat wont return to normal sitting position, its laid out almost flat. How to fix this? I am guessing there is a wire in there somewhere that will release it ...
View 1 RepliesI folded my back seat down, now it will not lock into the up position! I inspected the locking mechanism and it doesn't appear to have anything wedge in there.
View 4 RepliesOn my LS 600 HL- there are two buttons on the rear door handle. One is C and other is M.
One lights up, when pressed. What is the function of each?
I would prefer to leave the back seats in reclined position permanently but I find that they go back to erect position often (I didn't particularly test this function). What is the function of the C and M buttons?
I have a 2012 2-door R with sunroof and navigation. Almost from the very beginning the driver's seat had a problem. It would not hold the position of the back. It would slowly keep going back. Over a couple of days of driving (less than 2 hours per day) I would have to adjust the back about a 1/4 turn of the wheel to get it back to the original position. I have taken it back to the dealer twice for this and they could not find anything obvious.
They said that they would need to take the seat apart in order to figure it out. According to them I am the first one with this issue they have heard of. I am debating if I should keep adjusting it every couple of days, or take the chance and let them take it apart, hoping that there will be no collateral damage in the process. How easy/difficult it is to get to the guts of the seat?
I have a 2000 Regular Cab Work Truck with non power split bench seat. The passenger side back will not hook in the up position.
Before diving into it. Is the mechanism broken or is it something I can fix if I tear it apart? There is nothing stuck under or behind that I can tell.
Does the memory seat function remembers the back position (angle)? Or does it just remember the height and forward/backward position of the seat? The back angle position is not remembered in my 2014 Avalon Limited but I am not sure whether I should report this as a problem or whether that is just the design.
View 2 RepliesI've just bought a 2005 XC90 and one of the rear (3rd row) seats is jammed in the uprigh position and will not fold down. The problem is that the lever does not release the base of the seat to slide back.
I have tried poking my fingers in and have examined the side that is working to see how the mechanism works. It would appear that the catches at each side that hold the base of the seat in position do not swivel around enough when the lever is lifted up. I have tried lifting the lever as far as I dare but I'm worried that if I try any harder something will break.
The setup is:
MK IV .:R32 with 99,000 miles
Stage 2 clutch with 16.5 lbs. single mass flywheel
The clutch, flywheel & throw-out bearing all have about 20,000 miles on them
For some strange reason it looks like my driver's side axle keeps sliding out from it's position in the differential. This 1st happened after I did a dyno run about 6,000 miles ago. I lost half of my transmission fluid cause the axle shaft back out about a half inch. I guess the spindle stopped the shaft from backing out all the way. It appears to have happen again. What holds this axle in position? What keeps the axle from backing off like this?
My shop said the bearing/seal looked new and in good condition. Besides, it's a $15 part. We believed that the axle just snapped into position but after 4 nights at the drag strip it appears to be leaking again.
CV joints look good. Axle looks good. Transmission and differential all look good. Dog gone axle just keeps sliding out. Did the dyno runs damage something?
ALSO, on night two I did 4 strong passes back to back. Some with wheel slip and others hooked up solid. That night I developed THE HAMSTER WHEEL. Thought it was just a heat shield but I hear a noise that can only be explained by HAMSTER WHEEL. It only seems to happen when driving slow and on then off the clutch. Is it the dust shield? Is my rear main seal damaged? Or is it my timing chains on the way out. It only sounds funny at slow speeds with clutch movement. Too hard to trouble shoot alone.
My wife tried to close the hatchback door on our 2010 Prius I, something was in the way, she forced it and now I can't get the door to unlock. I tried the manual door release which is small metal lever on the lock assembly (as covered in the user manual); however, the lock won't release the striker. I've unbolted the lock assembly to see if the striker was jammed in the lock mechanism. I can now rock the lock assembly back and forth and I don't see any foreign objects in the locking mechanism, but still cannot open the lock. How to manually open the lock mechanism (is there somewhere I can apply pressure to force the mechanism to open and release the striker)? Again, the metal lever discussed in the user guide does not work.
View 3 RepliesI put the rear seats all the way down to haul some gear, and when I went to raise the rear passenger seat back up, I found it would not go back up. The middle shoulder belt is stuck in position. I removed the plastic clip, unbolted the metal frame, tried to jiggle what I could with a screwdriver, to no avail. I used to use this belt for the kid seat, so perhaps keeping it in position for so long did something to the linkage.
The car has 80k on it, 2000 Passat V6
I have a 99 1.8t and my sunroof motor is dead when i try to manually shut it, it just keeps sliding back . How to properly shut it manually if it's raining outside.
View 9 RepliesNot sure what's up with my car at the moment guys, but it seems. Whenever I go above about 55mph it feels as if the car is sliding back and forth. Its most noticeable at about 65mph where you can see the speedometer nudge backwards and forwards maybe 2/3mph at a time. I'm not sure if the engine is doing this but it does feel like it stops the starts then stop and starts etc. I'd say its also more noticeable in cruise control also. Car is an automatic 2.0L engine ...
View 2 RepliesQuite awhile ago my key started to randomly get stuck in the middle ignition position but it was happening very rarely and some gentle jiggling was letting me take it out easily. Well a few days ago that went from very rarely to each and every time I start the car.
Now its a tossup whenever I go somewhere whether the key will pop out like it should or I'll have to fiddle with it for anywhere up to ten minutes.
The car never has a problem starting, its only when I have arrived somewhere and need to take the key out that is an issue. I've managed to remove it every time so far but it has taken a fair amount of WD-40, jiggling the bejeezus out of the key and steering wheel and plenty of patience.
See my sig for truck.
I have 3 kids in the crewcab. 2 are in booster seats, and 1 still riding in a Britax. The 2 in booster seats can buckle their own seat belts in the wife's Odyssey. But they cannot buckle their own in the truck because as they try to push the 2 pieces together, the short 'female' end slides down between the seat and seatback. So I have to buckle them. Every time.
Anything to prevent the female end from sliding down? I'm thinking maybe putting a ~4" long 1-2" diameter piece of tubing around the belts. Something like that.
I had a question regarding the rear sunshade. Currently my sun shade is stuck in the middle position and it is very annoying and also is reducing my visibility in my rear view mirror because the bar is in the middle of my view. I took it to my local dealer and they said just to put it in the lower position would cost $800-1000. Does this seem fair ? I didn't break it, and why should I have to pay for something that is a malfunctioning part. The worst part is my rear view mirror is also turning black in the inside of the mirror also reducing my visibility ?
View 11 RepliesIs it ok to install a convertible car seat, in forward facing position, in the middle of the rear seat?
I only ask because i noticed the LATCH tethers at the bottom on the left and right side, but not a pair in the middle. However, there is oddly 3 top anchors on the backside of the back seat. So the middle anchor is making me wondering whether it's ok to use the LATCH anchors in the middle position.
If it matters, we have a Britax Marathon 70. My wife wants us to drive an SUV for our trip and I want to use the prius... The huge SUV has LATCH anchors in the middle position as well as the side positions (i.e. for a total of 6 anchors, or 3 pairs, in the SUV vs. the 4 anchors or 2 pairs that I see in the prius).