My '96 Suburban 1500 4x4 won't shift into 4 wheel drive. When I push the button for 4 Hi the light just flashes and stays in 2 wheel drive. The switch is good because I can hear it engage when I push the button. There seems to be a small amount of fluid (pinkish color) leaking from the transfer case but I couldn't get a good look at it tonight since it is about 10 degrees in my garage right now.
View 9 RepliesWhen I shift the car to drive it revs up to 3 or 4 rpms but only goes about 10 to 15 mph. It doesn't produce power like it should.
View 1 RepliesWhen I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 RepliesI have a 1988 F150 which is in beautiful shape. My father in law had it since 1989 and had "babied that truck" according to him. So it's running great, has a mere 92,000 miles, is an automatic with 4X4 with manual shifter to put it into 4X4 or Low 4X4. Here's the questions: When driving in rear-wheel drive mode (I never drive it on the street in 4X4 - we don't get snow here in SC) it has developed a hard shift from first to second. It feels like it bumps when shifting. When empty it shifts at about 3200 RPM at average acceleration, which I think is a little high. Does RPM even matter when the shift occurs? Can the tranny be adjusted to shift at a lower RPM? Is my tranny about to go kerplunk? The transmission fluid was a tad low so I topped it off but that didn't seem to work.
View 2 RepliesMy 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 RepliesI recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
Do a 2004 Saturn view front wheel drive transmission will fit in place of an all wheel drive...
View 1 RepliesMy '96 K2500 w/7.4 is running rough.
I've replaced: cap, rotor, fuel pressure reg, injectors (Bosch Design 2's), plugs, wires.
Had it timed today and it still runs rough. Really rough sometimes. I'm getting no codes.
In the morning when the engine is cool, I'm going to pull the pugs and check them, and verify the plug wires are installed correctly.
My front passenger window switch seems to have died. Where is the easiest/cheapest place to get one right away?
1996 1500LT, window works fine when I use the driver door switches.
I know I need to remove the reservoir to replace the pump but I can't get it out. I removed the storage compartment, then the bolt connecting the translucent top portion of the reservoir that connects to the front and the side bolt that connects the reservoir to the side of the truck. It is loose but I still cannot get the reservoir out.
View 1 RepliesMy Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
When turning right, it seems as if my brakes don't want to work. There is somewhat of a grinding sound and what I can only describe as a "shutter" from the pedal. They work great going straight or turning left. I should also mention that the steering locks up when turning sharply, haven't noticed if it's only when turning a certain way. This happens mostly when backing up. Also, the ABS light is on occasionally. I drive a '96 GMC Suburban.
View 7 RepliesMy 2003 Suburban shakes when I drive over 70 mph. I don't know if the tires need realignment?
View 4 Replies[URL].....................
If I accelerate gently and keep the rpm down to about 2500 or less, I get a normal shift from 2 to 3 and I can then accelerate with vigor without any apparent problem.
If I accelerate the way I normally drive, at the 2 to 3 shift point the transmission misses the shift and I have to let off the throttle for a few seconds and wait for 3rd to engage. I usually see no codes, but once in a while P0758 reappears.
Both solenoids A and B have been replaced, as described in the thread referenced above.
More symptoms, and maybe this is a vital clue: the 3 to 4 shift is fine, but I've noticed that lockup takes a while to occur. When locked up, I normally see almost exactly 2000 rpm at 70 mph. I am seeing about 2150 rpm at 70 mph until lockup finally takes place, but I can't say exactly when it does happen---I have to watch the road now and again.
I understand there are a 3-2 solenoid and a pressure control solenoid, but I don't know enough about their purposes to decide that either needs to be replaced.
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 RepliesI have a 1999 GMC Suburban(5.7) with 173k miles. When the outside temperature is above 80 degrees F and I have been driving for about 30 minutes, I get a hard/firm shift from 1st to 2nd. It shifts to the other gears normally. When the temp is below 80 degrees, I can drive all day without any problems. Any clues for what may cause the hard shifting on hot days?
View 2 RepliesI have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI have a 00 Suburban 1500 4wd and when I move the steering wheel the tires do not turn. I looked and a nut is missing from one of the pieces! Not sure what it is called!
View 2 RepliesMy 96 civic stalls when i put in drive sometimes, problem comes go's, was told tps sensor or trans control solenoid ?
View 4 Replies1996 dakota v8 automatic 4x4. tranny rebuilt 3 years ago got stuck in the mud and every since then it is stuck in first. wont shift no matter what i tried to adjust the tv cable and it didn't work at all. don't know much about dodge transmissions iv always worked on 4l60e in chevys. I don't know were to start. Where to start. iv been reading about the governor valve and shift selnoids are there any way to test any of this? first pulls strong and reverse works
View 1 Replies96 Taurus 3.0 liter OHV will not shift out of Park. I tried the workaround in the owners manual where you take the key out, re-insert it, turn it to the OFF position then start car in neutral, but shifter still will not come out of Park. Fuse #5 is fine, and all my brake lights work. Steering wheel is not locked.
View 6 Replies