I have a 1995 Subaru legacy wagon, 176K miles. The reverse went out about 10 months ago; all the other gears shift fine and it runs great. Do I have a bad transmission or could it possibly be some kind of switch or solenoid? I have searched the net for hours and keep coming up empty.
View 1 RepliesMy 1995 Legacy is slipping in reverse while backing up an incline. On level ground it seems fine. I Changed the fluid, but it's still doing it. Forward gears seem fine. It's an automatic transmission.
View 1 RepliesReverse stopped working after it's been driven for a while. It works when it's cold. I'm actually hoping this was caused by my stupidity (though it may have nothing to do with the problem). A while ago I wanted to change my oil, but opened the auto transmission plug instead. I decided to put new trans. fluid in it. I thought I would add trans fluid until I could see it on the dip stick. After the problem with reverse started I tried to again read dip stick but can't tell where the level is, so I decided to drain trans. fluid to measure it. Owner's Manual calls for 8.8 qts. Drained fluid measured only about 4 qts. I added more. Now it looks like dipstick shows it ~2 inches above the full/hot mark. Questions:
1) Would fluid level affect reverse and not forward (with which there is no problem)?
2) Is method of draining trans. fluid & measuring it a valid way of telling how much is in it, i.e. would all... or most... fluid drain out so the 8.8 qts. in the owner's manual should be added back in?
3) Am I misreading the dipstick? I've tried letting it set for 4 or 5 days, but still fluid seems to smear high on the dipstick.
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesMy 1994 Subaru Legacy has been running unbelievably smoothly for the 7 years that I have had it. It has just over 160,000 miles on it, and our mechanic suggested that we change the timing belt as preventative maintenance. Since that incredible investment (worth over 50% of the car's value), I have had one problem after another. Once running, the car runs very well, but getting it started is another story. It takes several tries to start, it shakes back and forth, it makes horrible noises, and once the engine finally turns over, it is hesitant to engage the gears. The mechanic thought it may be the cam sensors, so he replaced them. That made absolutely no difference. What could be wrong with this car that was perfectly find until the timing belt was changed?
View 4 RepliesMy mother in law gave her 1995 Subaru to us last year. She told me not to use the parking brake because the wheels seize up and to drive it often. We did not need a third car and every third day of not driving it the rear wheels would seize up which would require me (once in the snow) to jack the car up, take off the rear wheels, and tap the drum with a large hammer. Doing this would cause a huge mess because of the rust which fell onto the driveway. So recently I told her that the drums, shoes, and most likely the brake lines needed replacing and I would not pay for that as I didn't need the car anyway. Her response was that If I had driven the car every so often then it would have been fine. At which point I raised the safety issue with the braking and so forth which she flat out rejected saying it was fine when she drove it. Now I'm being blamed for the problems with her old neglected car. Should I just have the thing towed away or try and get it fixed?
View 18 RepliesOk. I replace my alternator on my 1995 Subaru Legacy Ls. Everything went great. Last thing I did was to connect the positive cable on the battery. When I did it sparked alittle. Well when I got into the car to start it nothing. Turn the key nothing. The knob on the shifter won't go in to get out of park. Neighbor checked my battery said it was fine. But nothing will come on. Nothing.No lights. I had problems with my ignition before. Do you think my ignition went out? Honestly don't know what to think. Some one told me that these cars have a secondary security system. If it goes on you cannot move the knob on the shifter and when you turn the key on nothing?
View 2 RepliesThe car has 175,000 miles on it and is having issues starting but only sometimes. The starter turns over but the engine doesn't catch. Usually if I open the hood, pretend to know what I'm doing, and wait a bit, it will start within 10 minutes or less (sometimes it takes a few tries.) I hear a click when the starter is going and the engine isn't catching, very much like the click I hear if I'm driving with the AC on and the AC needs to draw power. I've recently had a tune-up including new fuel filter, spark plugs and wires. The mechanic can't figure out what's wrong (doesn't seem to be the battery or the battery terminals). The car even started up FINE at 40 below. I can't really see a pattern to it.
View 3 RepliesI have a '95 Subaru Legacy L Wagon AWD 5-speed manual shift. There a new noise that seems to be coming from the front half of the car. I can't really describe the noise, but it only happens when all three conditions are met. If they are, the noise is continuous.
1.) The car has to be in gear--not neutral. But it doesn't matter which gear. I tried revving the engine in neutral, but nothing happens.
2.) I have to be accelerating on the gas petal. If I let off the gas--even if the engine and vehicle speed haven't yet dropped--there's no noise.
3.) Engine speed needs to be at or above 2,000 RPM. It gets louder at higher engine speeds, but it's pretty much proportional to the "normal" noises at higher speeds.
What might be causing this?
So I have a 95 Legacy sedan, FWD. It's been a kind of problematic car, and the engine was replaced about 5 years ago (I assume with an old unit, but I'm not sure though because though I was in the family I wasn't driving it then). But, it's held up and has continued to be at least roadworthy. But recently, it's developed an issue where the engine will just randomly die while I'm on the road. All/most of the dash indicator lights come on, but if I shift it into neutral and turn the key, it'll come right back up. Occasionally it'll die again almost immediately, but usually it'll be fine for at least a while. And anecdotally, It seems to happen more frequently at lower revs such as idling at a red light (though will occasionally happen while I'm moving), and when the engine is cold - generally once I've driven around for a while, it's not a problem anymore.
View 3 RepliesI have a 1995 Subaru Impreza that I have been nursing along for the past 14 years. Recently, if I drive for a decent length of time (~10 miles), turn the car off to go into a store, and then try to start it up again, it won't start. It turns over fine, but never fully starts. If I let it sit for 20-30 minutes, it will start back up again. The temperature gauge reads normal--between hot and cold. Is there another temperature sensor that might be malfunctioning, telling the car that the engine is too hot to start? Where/what is this called?
View 6 RepliesI have been having trouble with the shift solenoid and the trans going into limp mode. I recently replaced the shift solenoid and I now have the same problem but just when the temp outside is above 90 F or when I sit in traffic or idle for more than 3 or 4 minutes. The same code p0758 comes back up. I was thinking maybe the temp sensor?
View 2 RepliesMy 02 Legacy with 185k suddenly developed a whining noise I believe from the transmission. The noise coincides with engine rpm. The noise lessens when the load is taken off the transmission when at cruising speed. The trans shifts perfect and the fluid doesn't look too bad.
View 2 RepliesI started my Subbie and all the lights just start going crazy on my dash. So I pulled of the road and started freaking out, Never had a hint of a problem. So I pulled in AutoZone and they ran the codes and now I'm being told I have to replace the brain to my transmission WTH? I don't own a DODGE!!! Had 3 different dodges and the tranny went on all. So I wont own one because of transmission problems. Now my Subaru has been parked since it can only get worse. Is this normal? All the error codes are...
P0700 Transaxle Control System (MIL Request)
P2762 Torque Converter Clutch Pressure Control Solenoid Control Circuit Range/Performance
I had the car worked on a while back. They replaced the clutch and the viscous coupling in the transmission. ('03 Subaru Legacy manual transmission) Things seemed fine, then I realized my reverse light was acting like it was going out. Fuses are fine. A while later the car decided the clutch didn't need to respond as smoothly. Then: "Nope, you're funny to think you can drive me. I'm not budging." The car started grinding gears. I have to slam it into gear for it to work so I can drive it home and let it sit. The car will go into gear when off, no problem. New fluid has been put in. Bled. Then some sort of SUPER LUBE was put in and it still grinds. What might be happening? I really don't have the fundage in order to buy a new car at this time. But at the same time I hate feeling like I'm chasing a rabbit down a hole..
View 4 RepliesHad tranny fluid and filter replaced a couple months ago. It's in a 35 foot motorhome (F53 chassis). The motorhome is within it's GCWR. Climbing a 6% grade at 3,500 rpm, little more than half throttle, like all the other climbs. 80 degrees out. Engine temp was on the letter "R" on the word "NORMAL". All of a sudden my engine redlines as if it popped into neutral. I let off, put it into neutral, and try "D" again. Nothing.
At this point it's uphill so it's naturally slowing down and I try "2". Nothing. Even slower and I try "1". Nothing. Pulling over blocking the right lane on a blind curve on a grade is scary. Had pylon cones out, waving traffic to warn them down a ways, etc.
No fluid on the ground, no slipping prior to this. I have reverse. I see no obvious linkage or electrical/wire issues underneath (from road debris, etc). It's at a shop but I want to know all I can so if they come back with something outrageous I can make a decision. I never pulled the stick, as I was coordinating traffic, highway patrol, a tow truck, etc.
I have a legacy. Notice some slippage between 2nd and 3rd and 3rd and 4th. Also noticing an extreme burning smell when vehicle first gets started (for about 15 min) it's gagging it's so strong and pours in through defrost but can be smelled standing outside car also. Finally I parked in friends garage and notice some dark weird colored fluid on ground when I backed out, I dont know if it's oil or transmission fluid.
View 1 RepliesI have a 2013 Outback that has since new chugged and has had a feeling of not going smoothly through the gears up to around 30 mph (mainly around 20-25 mph). Since it occurs intermittently the first two times into the dealer to fix it they found nothing wrong but on the third time back in they found that Subaru sent it out from the factory with 1/2 quart too much tranny fluid. Dealer drained to the proper level but I am still noticing the same symptoms only not as bad as before. Took it back for fourth time and after they drove it for a total of 10 miles and hooked it up to the computer they said they could find nothing wrong. My question is driving it 10,000 miles with 1/2 qt too much tranny fluid going to have caused damage or possible future damage to seals, etc. When I asked the Service Manager that he responded that I had plenty of warranty left.
View 2 RepliesMy brother-in-law asked me about his 2010 Hyundai Santa Fe. It has an automatic transmission, that's where the problem is. Several times recently it doesn't want to go into reverse or park. Shifts fine, fluid fine, no smell or noises. Vehicle has about 68,000 miles on it.
View 1 RepliesMy 2000 Subaru Outback (75,000 miles) runs well almost all of the time. Every so often, especially when the weather is cold and I have been making many short trips, the transmission will refuse to engage into any of the forward gears (Auto-Trans). It will do reverse, no trouble, but not the forward ones. It does not do this with any sort of regularity or consistency. I have had it checked by my mechanic and he said that although it did this it sounded fine and was not shifting roughly. Thinking it might be a fluid pressure problem, he put in fluid additive to soften the seals and this worked for about a week, then back to square one. I saw enough notes posted on other forums by other Subaru owners to know that this might be an issue with this year's model--maybe some sort of quirk that I hope can be fixed without a new trans.
View 5 RepliesI have a 04 Explorer 4.0 4x4 with 130,000 mi. It all started about 3 months ago. The truck would neutral out while driving. After changing tranny fluid and filter, along with rear speed sensor the problem returned after driving 3-4 miles. After digging deeper I found the transfer case was bone dry and fried inside. Replaced the TC and check fluid level again. Back out of garage and drove the vehicle approx. 2 miles. Stopped to grab a coffee and left truck running. Returned to find I had no reverse or drive. This is after driving it to where I was. Towed truck back home.
I noticed the vehicle would start in gear. Replaced neutral safety switch ( grooves properly aligned ). Started truck, reverse lights come on when in reverse.. The problem now is when I put vehicle into R,N,D,3,2,1, the truck does one thing... REVERSE. All gears put truck into reverse, no forward movement at all. I attempted to replace safety switch a couple of weeks ago but was unable to remove the nut holding the lever on. 2 days I spent on that nut. Now I'm wondering if I did something inside the tranny when I was wrenching on that nut for 2 days?