Subaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
Jun 15, 2011
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
View 1 Replies
Advertisement
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
View 2 Replies
I bought (in November 2012) a 2009 Subaru Impreza. On a couple of occasions, when I put the car in Drive, it started going in reverse (in a flat parking lot). Each time, I put the car back in Park, turned the ignition off, started up again and it seemed fine - till yesterday. I was in a parking lot again, tried putting the car in drive and it went in reverse! A few times in a row, till I got so close to the vehicle behind me that I had to call roadside assistance... What's going on??
View 4 Replies
My subaru pulls very hard to the right, so hard that I can not go any faster than second gear (It feels to un-safe) I hear a like metal on metal kind of noise, almost like a ding or a bell sound. It wobbles very bad also. It feels like my tire is about to fall off! I tried to wiggle or move the tires to see if they would move and they did not (Advise from a mechanically inclined friend) I was driving on a muddy road when it happened, and I bottomed out at least once. When you look under the car you can see exposed metal, it is dirty under their obviously and the metal that we saw was not dirty so maybe something slipped out of place or fell off? The bar that connects to the wheel has a rubber protectant thing against it or covering it and that is where the exposed metal was.
View 2 Replies
I have an Elantra 2012 sedan GL and last year i tried installing HID's. It worked for a whole but then it stopped after. I learned that it wasn't getting enough power so then yesterday I bought a wiring kit to be able to wire my HID to tap to the battery to get more power. Everything was fine till I got to work but when I had to leave work., there was an issue. Whenever i switch the gear from park to drive or reverse or neutral. My car seems to jerk. And when I'm driving and it changes gears, it also jerks. Kind of the same thing how if your driving a manual car and you change gears wrong. This happens when my lights are off. But when i turn them on it then stops. And when i turn it back of it doesn't do it anymore.
View 5 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
I have a 2005 Hyundai Elantra with approx 155,000 miles on it(I don't know if that matters). The car started ok at first. When I put it into reverse, I noticed that it was really hard to move the gear shift(which it's normally really easy). I put it back in park and let it sit for a minute thinking it just had to warm up a bit more.
When I tried it again, it was still hard to shift, but this time when it got into gear I heard a loud clunk. This scared me, so I put it back in park and turned off the car. Now it won't start. All of my lights(headlights, dashboard lights, radio) come on, but the engine won't turn over.
I don't know if any of the following is relevant but I'm putting it out here anyway just in case it is: The battery is only a year old(and since all my lights came on, I don't think it's dead)I had an oil change on Saturday. The belts were replaced a few months ago. My check engine light is on because of an O2 sensor.
View 5 Replies
Recently purchased this Monte Carlo SS with a bad engine. Picked up a really good engine and it sounds great. Backed the car out of the garage, and when I shifted into drive, the car would hardly move. It felt like it was starting out in high gear. Had code P1860 (Trans converter clutch) set. Car has 150K on it. Suspected bad trans. Just had the trans rebuilt by AAMCO to the tune of $1100.00. Still have the exact same problem. The car will go in reverse just fine, but it won't hardly move forward. The old engine pushed a lot of antifreeze and oil through the exhaust. When I started the new engine, it smoked like a smoke stack for about 20 minutes, but then quit smoking. What am I missing? The trans is full of oil, and all connections are fine.
The Monte Carlo is a 2000, not a 2001.
View 6 Replies
This morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
View 9 Replies
I have a 2001 Lincoln Town Car that has an intermittent vibration that can be felt when seating in the car and you move the gear shift lever to D for drive. The car has 141,000 miles. It is an automatic transmission. The vibration cannot be felt when touching the steering wheel. What could be causing the vibration?
View 3 Replies
I have a 08 Subaru 2.5i Impreza and until now I thought this was a fluke but it is happening more frequently this week.When I park my car I engage the the parking brake and put the shifter into first gear, turn the car off ... etc... When I go back to the car I depress the clutch, start the car, apply the brake and disengage the parking brake. I then proceed to shift to reverse to back out of my parking spot, here is where the problem lays. More often then not the car shifts to reverse and I am on my way but every so often the shifter refuses to go into reverse until I release and depress the clutch pedal. After that it drops into reverse and away I go.
View 4 Replies
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
View 2 Replies
I have a 09' 4cyl automatic engine with 54k.
About 30min ago when when I parked the shifter would not move past neutral into reverse and go into park. I can go from D into neutral or the next slot over for manual shifting. Naturally this causes a problem as you can't take the key out of the ignition if its not in park.
I took a screw driver and popped open the cap for the shift release button and used that to move it into park. Turned car off, back on, etc etc seemed fine. So when I tried moving it into reverse and it wouldn't budge. It instead would make a electronic click or snap coming form the steering column but more back toward the engine. Like more into the dash area but back in it. It would make this noise every time I attempted to move it but it wasn't a continuous sound. Just once with each jerk to the side to move it out of park.
So the car works fine except for this. I used it with the screw driver/shift release to unlock it and it drives fine. Goes into reverse and back in park but if I move it into neutral or drive it will not go back into reverse or park.
View 1 Replies
My 1998 1.5 auto revs and thumps when engaging gears when cold, have read in other forums about similar probs and some say a sensor problem?. Transmission has been replaced bout 10,000km ago by previous owner maybe didn't need to be but not sure. Seems ok later in day when hot, has had fluid changed with recent service
View 3 Replies
My Subaru want to stall when it shifts from a higher to a lower gear when driving up a grade/hill. Also does the same thing when pulling out from a stop sign or traffic light. You need to pump the accelerator to get it going.
View 1 Replies
Sometimes my car, a 2000 Subaru Outback Wagon with 115k miles, when stopped in drive will slip into neutral. It is an automatic and is still in drive when this happens. It does not happen on a consistent basis. It seems to happen more often when it is either wet outside or after it has rained. However, it does happen when the sun is shining brightly too. Sometimes when I am driving, there does feel as though there is a delay when I press on the gas almost as though it needed to kick itself into gear. Any thoughts on what this might be and why this is happening? It has been happening since last fall.
View 5 Replies
This morning my 2011 Camry LE won't start. Based on looking at car manual I think the 'Engine Immobilizer System' is still engaged and perhaps not recognizing my key, neither of them since I tried the spare as well. The instrument panel stays black and I can not turn the key or even move the gear shift into Neutral.
Any way to fix this without calling for a tow? So.... found out the problem! The steering wheel was angled slightly. With key in the ignition we jerked the steering wheel slightly and it released the ignition and was able to start.
View 3 Replies
I recently had my Subaru Impreza (2011) brought in for repairs to replace the brake pads and rotors. Upon driving home from the repair shop, I noticed that it was a lot harder to pull up on my parking brake than before when I parked.
My question is: is this a sign of something I should go back to the mechanic about? Is there such thing as the parking brakes being on TOO tight? I just wanted to be sure.
View 2 Replies
My 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
View 4 Replies
Vehicle was repaired after front end collision and I get no codes found on scanner, had some bad connectors which I replaced and codes went away. I don't get ready light and the dash lights do not cycle off (ABS, SRS, Check engine, Etc. Etc.) The car will shift into neutral but not drive or reverse. Has new Aux battery and Hybrid battery is showing two bars. What to check ?
View 6 Replies
I am experiencing a slight vibration with in drive or reverse but not when it is in neutral. I change the spark plugs and checked the PCV. I have the latest model already and I replace the gasket in the PVC. There is no errors in VAGCOM.. What could be causing that? Mounts???
View 4 Replies
