On my 2007 Subaru Forester (100k miles) the CEL light is on and my cruise control light is blinking (cruise control does not work in this condition). Computer scan indicated front O2 sensor failed and my mechanic replaced it. No joy. Computer scan reported 0 data from EGR valve--replaced it. No joy.
View 2 RepliesI just bought a 2006 Subaru forester with 130K miles. Recently, the check engine light came and at the same time the cruise control started flashing. I brought it to the mechanic who said I had a bad catalytic converter. The car seems to be running just fine and now a day later the engine light is off.
View 3 RepliesI have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.
View 2 RepliesI have a 2005 Subaru Outback with 179,000 miles on it. My engine and cruise control lights flash on and off....have been doing this for 6 months now....intermittently. My mechanic said the he cleared the computer and to wait and see if it happens again. He said that it might be the catalytic converter. The car runs fine whether or not the lights are flashing.
View 3 RepliesI have a 2006 2.5 limited turbo outback wagon. Recently the engine light came on not flashing..the cruise control light is flashing. I live in a very remote area over a hour away from a dealer ship..and having problems finding someone with a diagnostic tool..Am I damaging my car by driving it still..I did just prior to the lights coming on filled the tank and after checking the cap I realized I did not tighten it as I should have.
View 6 RepliesMy mechanic can't find the problem. Engine light comes on. Along with the flashing cruise control. His diagnostic doesn't show him the exact problem as the voltage changes. He has checked everything related, changed out the bank 2 sensor 1 oxygen sensor, but can't find the problem. I don't know the diagnostic code. But he says that it doesn't give him an exact code. Can only the dealer do this? Car runs fine.
View 10 RepliesAt a bit over 43K miles the check engine light came on with a blinking cruise light. Dealer has confirmed that both secondary injection pumps have failed for reasons unknown. I think this is part of the pollution control system.
View 3 RepliesHad an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 RepliesI bought a 2005 subaru forester xt a cohple months ago and then the CEL went on and the cruise control started blinking. The car also shook horribly. Long story short, and $2,300 later, i got the "head gasket set, water pump, timing kit, oil&filter change, " etc... Fixed. Question is, I am driving to Colorado from Maine in about two weeks. How long do subarus last after such repairs? Think ill get a few years out of it? Or should I sell it and buy a more reliable car before the trip out there.
View 11 RepliesSo I'm driving along with everything fine till I pull into a neighbors driveway to drop off some stuff. As I pull in, the check engine light suddenly comes on and the cruise control light starts blinking. As I have a scangauge II always connected, I put the car in park and check the code. It comes up as P0000. I get on my Droid III and google it - all I see is "null code" so I clear the codes and everything is fine. I figure "that's odd, but whatever". I drive home (about 1000 feet) and park and shut the car off and go inside to mull this over.
I go back out to check out the scangauge again and it requires starting the car to read out the codes. The car won't start. The battery is fine, and in fact it does the "rurrr rurrr rurr" strongly for 10 times before I figure it's not starting. I wait about 30 seconds and try again - same thing. I wait about an hour or two and try again and it starts this time right away, but then stalls right away. Start again and manually give it some gas and it keeps idling weakly. I'm able to back out and drive a short distance and come back without a stall. I let it sit for the weekend (no shops open anyway) and start it monday morning with my AAA card out... and it starts fine and runs fine all day. I basically forget about it.
About a week and a half later, I'm driving along a country highway at 55 Mph, and the same thing happens. Check engine light, cruise control light blinking and the cruise actually cuts out so I'm losing speed suddenly. I run the scangauge again and same code. The car keeps running fine though, I'm able to drive it back (w/out cruise control) the 5 miles home. Nothing out of the ordinary.
I go inside and google this some more, and there's some posts about the Scangauge causing this - but I've been using it for about 4 years w/out this happening. That said, about 2 months ago, there was a recall, and they flashed the ECU with some update so maybe that changed something, but still - worked for months before this happened. I had to get to work etc so I just cleared the code again, and so far 3 days without a recurrence. Currently I'm thinking about waiting to see if it happens again and going to Autozone and have them read the code to see if it really is the Scangauge not reading the code right or whatever...
I have a 2007 subaru outback ll bean addition with 67,000 miles. For the past year and a half my gas pedal has intermittently become unresponsive. The engine is running just fine but the check engine light and cruise control light start blinking and boom-no gas. After turning off the engine, the car won't start until the gas pedal has magically started working again. The dash lights continue to blink for several starts but then stop.
Prior to this problem, I have noticed that sometimes the console lights for the radio and AC blink and sometimes go dark at which point the controls are ineffective. As if this wasn't enough, just yesterday when trying to start the car, the engine was having trouble turning over with a rapid clicking noise. It eventually started but now the seat belt buckle alarm is out of whack and the speedometer displays "ER U1."
engine light and flashing cruise control switch--computer says replace bank one---so I replace with factory catalytic converter----six months later light comes back on with flashing cruise control switch and computer asking me to replace bank one---So I use computer to shut light off----four weeks later light comes back on----called dealer they said "we usually replace both banks"---I found it most painful paying for dealer supplied catalytic converter even when I was under the impression that it would keep light off.---This is my wife's car and she is not really buying the piece of black electrical tape I placed on dash over check engine light.---Am I dealing with a bad oxygen sensor ?
View 5 RepliesMy 2010 Subaru Outback recently surprised the hell out of me by simultaneously turning on the brake warning light, the traction control light, the check engine light and (just for a bonus!) disabled my cruise control while flashing the cruise control light. I pulled over, quickly surmising that all of those systems could not have failed at 70 MPH without instantaneous death to either me or the vehicle. Both apparently still being alive, I tried turning the car on an off to reset the lights. No go. Subaru was not going to miss this chance to get me to the dealership! (who I had avoided to this point!) As I was far away from home and the car being very healthy, it seemed, I decided to drive on. I proceeded to put a couple of hundred more miles on the car before I got back to town.
My car had 39,000 miles on it, 3,000 miles beyond the warranty end. I learned that I have an error code of P0171, "Fuel Trim Malfunction (Air/Fuel too lean)". So I guess I'm wondering about a few things...why would this sensor set off every light on my dashboard and disable my cruise control? Seems a bit overblown for running a bit lean. My gut tells me Subaru has a sensor/software problem they are not owning up to. I'm a big fan of conspiracy theories and this really smells like one...
Second, jeez, I'm only 3K miles over warranty, don't you think they'd cut me some slack. I mean I love my Subaru, or did anyway, until this happened. Now it's just another POS car that breaks for no apparent reason...
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
My 2005 Subaru Legacy 2.5i - the engine light is on and the cruise control light is blinking. This happened once before and it went away after I recapped the fuel cap. However, this time it did not work. The car is running ok.
View 4 RepliesI'm on a road trip and was taking off this morning when my CEL, vehicle dynamics control light came on steadily, with a flashing brake light. It's Sunday and no repair shops are open and I need to drive from CO to S. Cal today. Is it safe to travel? From what I've seen, it could be a problem with the gas cap or ABS is disabled. Haven't had cruise control light come on (yet), but haven't tried driving anywhere.
View 4 RepliesMy car horn starts honking and the lights start flashing, spontaneously. The neighbors are going to kill me if I don't die of sleep deprivation first. The problem started a few minutes after 6 a.m. yesterday, and stopped when I turned the car on I left the car running in the driveway (illegally) and then cut it off after about 30 minutes, and all was quiet until around 8:45 a.m., when it started again. The only way I can get it to stop is to press the UNLOCK button on the car's remote; but that doesn't make it quit for good, sometimes only makes it quit for a few seconds.
Anyway, I drove the car to work and it was nice and quiet all day. (I went by the mechanic's on the way to work and had to set an appt. for Monday but I don't think I can stand it until then. This morning the honking/flashing began at 1:52 a.m. I pushed the remote. It stopped until 2:08. It kind of went like that until I finally started up the car. It is now emitting carbon and I am a zombie. What can I disable or override until a mechanic can take care of this? Is it a mechanical problem? A goofed-up sensor? Is this tied to a computer chip problem?
Sometimes when the AC is on automatic control it will kick out of auto control into manual control and the fan will speed up. All this happens without touching anything. Dealer said it's working fine.
View 1 RepliesMy Keyless remote control is "DEAD" however my system is somehow engaged. In order to start my 99 Subaru Forester I need to reach under my dashand hold in the emergency override button. Car starts fine every time. Is it difficult to unwire this keyless system? I'm not going to keep this car much longer. Will probably replace car before end of 2013. Easy fix or keep driving as is? Any possible problems if I keep starting car with button release?
View 2 RepliesMy Tire pressure indicator light starts FLASHING after driving for 15-30 minutes. It does not stay on but continues to flash every 3 seconds. I stop to check tire pressure and my tires are fine. After a couple weeks of this, I took it to the Subaru Service who checked the tire pressure indicators and it said all 4 of them were bad. They reset them versus replacing them and 20 minutes after I left the subaru service center, the flashing started again.
Subaru says that it is unusual for all 4 to be back at the same exact time and recalibrating them should have fixed it. Now they would like to replace each of them for about $150 parts&labor EACH. That seems crazy. Is there something else wrong? Something else they can fix? Is this a legitimate repair? My subaru is the Limited LL Bean version, 6 cylinder, has 60K miles on it and is in top condition. Had new tires put on 10,000 miles ago.
I have to press Cancel before I can get my cruise control to work. I had a problem about a year ago where my cruise control wasn't working, and found out that a blown brake light fuse was the problem. Now I turn my CC on and the "Cruise" light comes on, I then press the set button, and nothing. I then press the cancel button and then the set button and then the "Set" light comes on.
View 2 Replies