My car has had a rough idle (no MIL). Scanned for codes and got the following:
P0552 - Power Steering Pressure Sensor - Low
P0553 - Power Steering Pressure Sensor - High
I'm picking up the part at the dealer this afternoon. I printed out a diagram of the component location, and it looks to be easily accessible.
I've been experiencing an annoying intermittent condition on my '07 Sonata (Lambda V6). I wanted to share this in case any of you are experiencing intermittent rough idle complaints in your Sonata (4G) as well. I was finally able to get it into the dealership during the malfunction; in my case, the MIL never lit. Here are the symptoms: ONLY after being fully warmed up, when coming to a full stop, or using just idle speed to, for example, pull into a parking space, or inch up to a stoplight, I would experience a very rough idle (I could hear the engine sputtering with the window down), see the RPM gauge bouncing, and feel the vehicle going "putt-putt-putt" as it tried to keep running under what seemed to be a misfire or too much load. The problem occurred more noticeably with the A/C off but still did occur with it on as well. While exhibiting this problem, acceleration from a stop gave a slight hesitation as well, but once going faster than 1,000RPMs, the problem went away totally. I thought it must have been my imagination until one day, I pulled up in front of a glass window and could see the reflection of my car lurching forward as it struggled to keep idling. Getting it to the dealership while it was behaving badly was the hardest part.
Once I got there, I got a tech to ride with me and finally, after 3 visits to the dealership, someone else witnessed the problem. Up until now, I've been asking people, "Do you feel/hear that?" "Huh?" I digress... The tech immediately said he thought it was a power steering issue and he thought there was an upcoming bulletin on it. I was sure he was wrong, I was thinking it had to be the spark plugs, wires, MAF, or TPS.
After getting the part in for me (Power Steering Sensor Switch) they put it in today and my vehicle is just as new again. It was never a serious issue, but was rather embarrassing to try and show off my Sonata and have it stutter and sputter like that it idle.
This part is complete speculation; maybe a more knowledgeable person can jump in here and correct any logical errors: Apparently, there is a switch in the Power Steering Unit that detects highway speeds versus slower speeds. When vehicle speed is above a certain limit, the power steering pump is either turned off or "turned way down" (so people get the stiffer feel of the wheel at highway speeds). When the vehicle slows down to idle (to be detected by this switch), the vehicle expects the power steering pump will draw full power from the engine and needs to have a slightly higher idle speed to compensate for the load. My switch was malfunctioning; it was not registering to the ECM that the power steering pump was under load when it actually was; the vehicle then did not bump up the idle speed appropriately, and thus, the rough idle and hesitation.
I recently bought a 08 Sonata V6, with 94K mileage. The oil pressure light comes on when the engine is idle (around 700-800 rpm). The seller told me that this problem started a few months ago, but the car has not been used much since then. He also said that he has changed the oil after that, but the problem still persists.
The engine light has shown up more recently, like in a week or two. I took the car to a mechanic and he could not guess what the problem might be. But he gave me the error codes: P0011, and P0051. There are no other obvious symptoms (e.g. oil leakage, low oil level, unusual sound from the engine).
I could not find any thread regarding both of these issues (Oil Pressure, and the error codes) together. Any connection between these two?
So far, I have realized that the oil pressure can be due to a bad sensor, and P0011 has something to do with CVVT, and Oil Control Valve (OCV). But I would like to make sure I don't just waste money by replacing the sensor and OCV.
I've got a troublesome misfire in a 2007 Sonata V6, 70k miles, which I have been trying and failing to track down for a long time.
More than a year ago, the owner of the car complained of rough idle. When this was first mentioned, I looked at the car, she and I talked, and I concluded that she hadn't changed the oil in some 20k miles. ...... Nothing else seemed wrong. I changed the oil, thinking that what she needed was an oil change.
Some time later, I was in the car myself and all of a sudden felt a strong bucking. Must've been a misfire. I recommended taking it to the Hyundai dealer, thinking the so-called 100k mile powertrain warranty would cover whatever it was (it didn't but whatever).
We drove it to the dealer. The dealer firstly informed us that the CEL had burned out, so we had missed some codes. The dealer further us the car needed new plugs and replacement of both upstream O2 sensors. Here was what the mechanic wrote:
"BETWEEN 35-40 PUT CRUISE ON AND WILL FEEL. CHECK AND ADVISE COMES AND GOES. MULTIPLE CODES STORED IN SYSTEM. ... P0300 RANDOM MISFIRE (ACTIVE), P0140 O2 SENSOR CIRCUIT NO ACTIVITY, P0154 O2 BS S1 NO ACTIVITY. WATCHED O2 VALUES AND FOUND ERRATIC READINGS. FOUND TSB 10-FL-012 SUGGESTING REPLACEMENT OF BOTH UPSTREAM O2 SENSORS. RECOMMEND COMPLETE SYSTEM TUNE UP FOR RANDOM MISFIRE. HOWEVER MISFIRE COULD BE RELATED TO O2 ACTIVITY.
So the owner went to a different mechanic and had the plugs, upstream O2 sensors, and one of the downstream sensors replaced. All OEM, I believe. ($$$!) (O2 sensor parts 39210-3C100, -3C200, and -3C400) Dunno why the downstream one was replaced, not my doing.
Following this, there was no real improvement. No codes either. The problem comes and goes, so maybe I thought it was fixed, but it has come back. Sometimes, it can be felt just slightly when the car starts cold. Other times, it can be felt just barely when driving at a consistent speed. Sometimes, the problem becomes really bad and jerks the car around. Other times, nothing.
What to check next? Coil packs? Intake manifold gasket? She never gets "top tier gasoline," but I would be skeptical that that's the problem. These are the top three suggestions I've heard.
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
I have a 06 sonata 3.3L v6. I have been having misfire problems and lack of power under 2000 rpms and at idle when I am either a stop or just warming the car. What is happening I feel it shake and feel the misfire but after it gets up after 2000 rpm at highway speeds its completely fine. It struggles getting up to speed if i press on the accelerator. I have changed the spark plugs and all the ignition coils maybe about 2 months ago, I have also have changed the camshaft position sensor for the rear bank. I believe that it could be the crankshaft position sensor but I want to make sure....
Obd2 codes: p300,301, 303, p0012, p0011, p0014,
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesIt's an 04 F250 with the 6.0, and has been there about five months now. The backstory I have been given is that it drove in running rough, gave crank position sensor codes, and the CPS was replaced. That was the last time it ran. Since then, it has had the CPS replaced five times, the FICM rebuilt then replaced three times, the engine harness replaced, and spent some time at Ford. It would only show about 30rpm while cranking. The engineer came and looked at it, said it must be the tone ring on the crank and that's it.
Here's where it's at for me: Cranking RPM peaked out at 57, but the fan rpm was about 180 while cranking and it sounded like it was cranking pretty quick. I disconnected the glow plug module, had another guy crank it while I gave it a quick shot of starting fluid, which it caught and started to run on. It sounded like it was running on fuel for a second, then shut back off and now cranks unevenly.
According to the owner this thing has seen lots of starting fluid in the course of diagnosing it, and there were no odd noises before it shut down so I suspect stuck valves from sitting so long. It did give me a whole bunch of codes which I will post tomorrow, including injector #4 high. I tried to do a buzz test but just got a message saying "unknown code, please wait" and then nothing.
I know it's on the steering column but is it down near the floor or on the engine compartment side?
View 4 RepliesFinally had a good scan done on my truck at the mechanics. The reoccurring codes were P0478 and P0470. It looks like a bad exhaust pressure control sensor. Looks like an easy fix.
View 14 RepliesI think I've tracked my power steering leak to some type of sensor on the pressure line, close to where it connects to the steering box:
I assume this is a pressure sensor? I got no CEL or anything like that when the fluid had leaked down to the level that the pump started whining pretty badly though. As far as I can tell by looking at pictures, the parts store replacement pressure lines do not have this sensor, or any provision to connect a sensor to it: Advance Auto Parts: Power Steering Pressure Hose by Powercraft - Part 71878
I may just put a replacement line on there and leave the sensor plug hanging and see what happens...
I have a 2006 Hyundia Sonata. I idles really bad like you pulled 5 of the six plug wires off when you put it in gear. Once you start moving a couple miles an hour it is fine. It is also perfect in park or neutral, not a hint of a problem. Put it in drive or reverse and it almost stalls.
View 13 RepliesWell, it's looking sort of depressing for my '06 Sonata! I had an oil change done yesterday and now I'm getting a Low Oil Pressure Light on idle under 1,000 rpm's. Today the check engine light came on and it's code P0021.
I also experience very noisy "bearing" type noise upon start-up which happens for about 10 seconds or so. This has been going on for a month or so.
During my online research it's appearing that I may be suffering from the dreaded Timing Chain Tensioner I've read a lot about.
I'm aware of the TSB (10-EM-006) and have a copy of it if needed.
My question is this...my Sonata has 151,000 miles on it, well beyond the 100k warranty period. Will Hyundai repair my issue as a warranty item under that TSB?
2007 Sonata V6 with 72K miles.
The car has developed a rough idle while in gear (i.e. when stopped at a stop light) and park (i.e. after I start the car).
It's starting to get a little annoying since I'm used to a very smooth idle.
I think this issue started within the last 2-3k miles.
Plugs were allegedly changed at 30k. A full tuneup was done at that time.
Wires are still original.
In idle and driving the car sounds rough as if a pulley was loose, after checking no pulley was loose but problem still persists. Tried turning wheel left n right n noise didn't go away or get worse its a constant noise, what it may be? Crankshaft pulley? Idler pulley?
View 2 Replies2007 Sonata V6. He's spent many hours and a good chunk of change at the dealership trying to get it fixed and nothing has worked yet. They honestly have no clue whats wrong which kinda scares me.
First off here is his problem. Occasionally when he starts the car it will idle very rough and struggles to accelerate to 30-40mph. When this happens he pulls over and shuts the car off for a few minutes then it will run fine again. When all of this happens there is no CEL or any light at all that flashes or comes on the dash.
Here is a list of things that have been replaced
Fuel pump
Throttle position sensor
Crank sensor
Plugs, wires and coil pack
I have 114,00 miles on my car. Plugs changed and decarbonization done at 99,000 as well as ECM reprogram or update ($99). Anyway, when my car sits overnight and starts it is getting a rough high idle until I feather the pedal or give it a minute or 2 and it is fine. It is warm now in the 70's and this just started. I had it to the dealer for oil change and they looked at it. There are no codes, they recommended changing the plugs and doing a decarb again. So I told them if I need plugs there is something wrong, Iridium OEM were installed.
Anyway, they suggested changing the throttle body since it has new sensors. I have have the TPS replaced before when engine was surging. They told me there are 2 sensors and one could be bad in throttle body. I don't get it, I use Hyundai air filter now and change every 15,000 miles and get oil changes regularly and they use Quaker State Synthetic blend. I am wondering if maybe I have a faulty PCV? I don't think that has been changed. Don't even know what the interval is. Previously I was told there was none, but I disagree.
What would cause me to get carbon build up like they keep telling me? I don't want trial and error and throw parts and money at it since there are no codes. I was going to drive it til it throws a code. I do highway driving in suburban area, mostly 65 mph. The car runs good, still the intermittent hard downshift when slowing down but nothing like before the tranny was replaced.
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
I head out to work this morning and truck drive fine. I do not get on it. I cruised on the highway for 12 miles at 70 mph. I get to a traffic light and then it begins to idle rough and my fuel pressure gauge reads 0. I replace both filters over a month ago and did the blue spring upgrade at the same time. I've put over 2000 miles on the truck since then without issues until this morning. Also the fuel pump was replaced by the dealer a year ago in July. No check engine codes. Where do I start looking?
View 13 RepliesI am checking my car parameters at idle. I was comparing the values of intake manifold pressure and vacuum. When I press accelerator or give gas means throttle plate opening my manifold pressure decreases and vacuum increases, I hear when throttle plate open more air come inside so manifold pressure must be increases and vacuum decreases. Am I right? if so which part will be culprit of this action?
View 3 Replies2006 Sonata V6 with 98K miles. The car has developed a rough idle, sputter/lurch while in gear, but not park or neutral. No CEL/codes. Have already replaced the spark plugs (OE), throttle body/FI cleaned, MAF cleaned, new air filter, coil packs OK... Mechanic said no vac leaks, FI spray pattern good, good fuel pressure, etc. Vibration dampener looks ok, no separation or wobble. Another post mentioned a power steering pressure sensor, which I will have checked, but the mechanic is at a loss.
View 7 Replies