Sonata NF (2006-10) :: Rotational Grinding Noise When Accelerating Through Hard Left Or Right Turns
Nov 17, 2013
I have a 2007 Sonata 3.3 V6 GLS (CDN model) with 102k km (63K miles). Recently, I am noticing a rotational metal-like grinding noise from the front left wheel / engine area when engaging in hard right and left turns - usually a long looped highway on-ramp or sharp 90 degree turns. The interesting thing is this only happens when I am accelerating through the turns - when I left off the gas and cruise I don't hear it anymore.
On the side, I am also getting a single clunk noise when shifting from Park to Drive and vice versa from the same area (front left wheel) - not sure if this is related (i.e. if this is all related to a failing CV joint or wheel bearing).
View 2 Replies
Advertisement
My 04 gli makes a rubbing noise when accelerating thru hard left turns.. but weird enough i can take the same turn at the same speed in neutral and have no noise at all. I changed both front wheel bearings and cant seem to find the answer. I brought it to vw and they checked the whole suspension struts springs cv's tie rods ect. and they all checked out good they said. the car used to have a exhaust and i just recently put it back to stock, could the exhaust make the noise perhaps?
View 1 Replies
Tonight while driving and accelerating fairly hard we began to hear a noise. The car sat parked for roughly 5 hours and then we began to drive it home (apx. 12-15 miles). About halfway through the drive the power steering went out and the battery light came on. The battery light would turn off and the drivers seatbelt light would come on even while it was buckled. These two lights alternated being on and off 2 times each. We heard something that sounded like a rock got kicked up into a wheel well. After getting the car home with no power steering we noticed the car had begun to run very hot. almost all the way up the gauge.
View 4 Replies
I just got the car back from repairs, there was a loud grinding noise coming from the left side of the engine. It turned out the whole rack and pinion setup was pouring out fluids and needed to be completely replaced also while it was in there they checked out an oil leak which ended up being the front valve cover and replaced a dead O2 sensor. The car has 99,300 miles
View 6 Replies
I have a 2006 Prius (150K miles) with a noise coming from the drivers left wheel. It is a hollow metallic squeak that only occurs while the vehicle is moving. It sounds like the wheel is making brief contact with something metallic at the same point on every rotation. The pitch of the squeak increases with the speed of wheel rotation. It does so while rolling, with breaks and without. The noise gets louder when turning right, and softer when turning left, though it begins to get louder again when the wheel is turned hard all the way left.
View 1 Replies
I have a 2007 Hyundai sonata and I'm having a strange problem with my car. It doesn't happen alot but whenever I make certain turns the entire front end grinds and stops moving. It usually happens after being parked at an angle then pulling out.
View 1 Replies
I have an 08 AWD GS350 ...
For the last few months, it has been squeaking whenever I make hard left turns, (into parking spaces etc, usually low speed). I thought it was the brakes, but just replaced all 4 pads and all 4 rotors. So that officially eliminates that.
The car doesn't have any unusual vibration, tracks straight, so I don't think its a wheel bearing or anything. I jacked the car up and tried to shake the tire/wheel to see if there was any play but don't see anything.
View 3 Replies
06 sonata v6 standard 16in tires. I do all my maintenance, but i am stumped. A sound that is best described as a rattle crossed with a metal object (bolt/nut) rolling down a rail. Strange i know. Checked for rubbing, nothing. Made sure all bolts and nuts were correctly tight. Does it whether braking or not during any speed. May be dropped object, but neither I or a mechanic could repeat during Right hand turn. I have changed my front pads and dbl checked that is not the cause ( was doing it before change anyway) my fear is I'm missing something and am fearful of a mechanical failure.
View 9 Replies
Ok in the last couple weeks I noticed when I am going left in a curve a grinding screeching sound from what sounds like my left front. It only does it when I am in a curve going left. It wont do it going right or just even turning a corner left just a slight turn.
View 2 Replies
I've got about 88k miles on my 2008 Impreza 2.5i manual. The last 30k miles on it have been rather rough (~60 miles a day stop-and-go highway traffic). Somewhere around 80k I developed a leak in my clutch hydrolic line that lead to a clutch replacement around 82k miles (I had a few leaks simultaneously so diagnosis of the clutch line took longer than optimum). I also had new break pads installed around the same time, tires rebalanced, alignment, and one new ball joint on the front driver-side wheel. Anyways, after this work I had a noise develop that I've had checked out twice and has yet to be diagnosed.
I am getting a grinding noise that occurs with both front breaks but at different, specific, reproducible points in the tire/rotor/etc rotation. It also only occurs with mild break pressure (most noticeable during a gradual, easy deceleration). The frequency changes with speed, so I know it is rotation point specific. Heavy break pressure does not generate the noise. The noise is also the most noticeable after the car has been at rest for a number of hours, and lessens the longer I've been driving continuously (but never goes away completely). I have not noticed much change as a result of moisture, and I live in Colorado so our humidity is at a minimum. I've also had my rotors checked to make sure they aren't warped, and I've been assured that my break system looks good and clean.
View 4 Replies
I drive a 2003 Hyundai Sonata. I currently have a slight grinding noise (or maybe more of a low growling) when I make left turns. This happened in the not-so-distant past and it was an issue with the power steering hoses (one had rusted through), so we (and by "we," I mean my fantastic father) changed it out. I thought this time it may just be low power steering fluid, but after checking it, I can say it's not low. I'd think if a hose was the culprit again, the fluid would be low. What we should look into?
View 1 Replies
I just did the brakes on all four wheels of my 06. I replaced the rotors and pads all the way around with Powerstop parts. I got them from RockAuto.COM as a complete set. The rotors were made in China generic looking things and the pads were Powerstop Evolution Ceramic Disc Brake pads.
Anyhow, I drove around to bed the brakes after getting them installed and now the passenger front tire as a small "rotational squeal" when you are lightly braking.
Oh, one more thing, I'll admit this up front. I did not put any grease on the back of the pads. This was mostly due to I wasn't sure exactly where or how much grease to use.
View 3 Replies
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
View 3 Replies
Back in January I had my right front wheel bearing and u-joint go out, so I replaced them both. At the time I didn't realize my outer stub axle shaft was wore so I just put it back in. After a little driving the right side started to "thump" and "pop" when I would make hard left turns driving around town.
I replaced the outer front stub axle shaft and seal again because the old one was worn down. This eliminated any play in the u-joint. After a bit of driving the thumping and popping noise came back.
I decided to dig into it today so I pulled it all apart. When everything is apart it turns easily, no issue at all. When I assembled the wheel bearing, torqued it to 55 ft/lbs and installed and "locked" the hub I noticed something peculiar. I can barely turn the whole assembly by hand. I have to put a good amount of force to get the whole assembly to turn at all. When I walk to the driver side with all the same parts there i can turn the wheel bearing and locked axle shaft with one finger on the studs.
I have been in this thing 5 times and can not figure out what the heck is wrong. I can't figure out why this stupid axle shaft and wheel bearing are so hard to turn, together or separately, and I can't figure out how to get my front end to stop that thumping and popping.
View 6 Replies
My wife has a 2002 Hyundai Elantra that has a rotational noise coming from the left rear wheel. We just got it back from the shop where they replaced the left front wheel bearing and rear brakes/rotors, and the right/rear wheel bearing was replaced about a year ago. It's a thumping noise that speeds up proportionally to the speed of the car. Normally I'd expect a bad tire or warped rotor, but the tires are relatively new and we didn't notice the problem before we took it to the shop last week (though it's possible we weren't hearing it over the wheel bearing noise they fixed). Is it possible we got a bad rotor, or the shop did something wrong? Or could this be something new entirely (which would be entirely typical for this car).
View 1 Replies
This auto has 143,000 miles on it. I recenty noticed a creaking noise from the left front when accelerating from a dead stop. The shop I have used for 15 years said that the motor mounts are deteriorating and should be replaced. I trust the guy but would like to avoid the $1,400 repair. There are no symptoms other than the ocassional noise.
What is the downside of ignoring his recommendation? What other symptoms can I expect if I delay the repair? Can this be a serious safety issue? I plan to keep the car for another two years unless I bite the dust first or the engine falls out.
View 1 Replies
I have a 2007 Honda Pilot. 65K Miles.
Several months ago, when turning left, regardless of speed, my wife starting hearing a noise. It is not a knocking or harsh grinding noise, but a low grumble (I don't have a great word for it). It's definitely rotational, it doesn't get any louder as speed increases, but it obviously happens more often. It seems to come from the right side of the car, I originally thought it was from the wheel, but just now I had it jacked up and had a neighbor who works on cars look at it with me and now I'm not so sure.
When I described the problem to him, he first thought it was a CV joint, or possibly ball bearing. After a few minutes looking under the hood, he quickly ruled those out. Boots were in great condition, and he remarked that everything seems to be very solid around the wheel.
I thought that noise was a result of weight shift to the right side of the vehicle when making right-hand turns, but we had the car up on two jacks stands placed on the jack braces, turned the car on and gave it some gas with the wheels turned left, and you can definitely hear the noise with zero weight on the wheels or axles. When you straighten the wheel, the noise subsides.
View 12 Replies
I have a problem! I have only had my 07 gs awd for less than 2 months. I noticed this morning when I turn my wheel all the way to the left or right it makes a grinding or like metal on metal noise. My brakes were done only a year ago, and this noise only happens when I'm turned all the way to the right or left.
View 11 Replies
Over the last couple of days, my 2009 Sonata V6 has developed what I best can describe as a rattling noise near the engine when I am accelerating the vehicle (noise changes based on throttle input). I only hear the noise with the car in drive, if I shift into Neutral or when I am in Park I don't hear the noise when I rev the engine.
View 6 Replies
I have a 2009 sonata with 33k miles, the last few days i hear a rattle noise while accelerating, the noise disappears while driving at more than 40mph...
View 6 Replies
Just put on eibachs and car is randomly making a grinding noise when slowly accelerating or braking.. Also noticing a fairly loud clicking noise when going in reverse. The noise isn't consistent and seems to happen more right after startup. I haven't gotten the alignment done yet and was wondering if this could be the problem. Will try and post a video soon.
View 8 Replies
